1、 AEROSPACE STANDARD CONNECTORS, RECEPTACLE, ELECTRIC, CABLE CONNECTING, REAR RELEASE, CRIMP CONTACT, AN TYPE AS34511Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electroni
2、c, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED1998-01R
3、EVISED 2011-12REAFFIRMED 2017-03THIRD ANGLE PROJECTION CUSTODIAN: AE-8C1 REV.A FEDERAL SUPPLY CLASS 5935 AS34511 SHEET 1 OF 3 REV. A PROCUREMENT SPECIFICATION: AS50151 SAE Technical Standards BoardRules providethat:“This reportis publishedby SAE to advance thestateoftechnical andengineering sciences
4、. The useofthis reportisentirely voluntary, and its applicability and suitability forany particularuse, includingany patent infringement arising therefrom, is thesole responsibility of theuser.” SAE reviews eachtechnical reportatleastevery five years at whichtime it may berevised, reaffirmed, stabil
5、ized, or cancelled. SAEinvites your written comments and suggestions. SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS34511A RATIONALE AS34511A HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. THE REQUIREMENTS FOR PROCURI
6、NG THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF SAE AS50151. FIGURE 1 CONNECTOR CONFIGURATION (CLASSES L,U & W EVIRONMENT RESISTANT) AEROSPACE STANDARD AS34511 SHEET 2 OF 3 REV. A CONNECTORS, RECEPTACLE, ELECTRIC, CABLE CONNECTING, REAR RELEASE, CRIM
7、P CONTACT, AN TYPE TABLE 1 - DIMENSIONS REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF AS50151. 1. DESIGN: CONNECTORS SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE 1. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: DECIMALS .016
8、. DIMENSIONS AND TOLERANCING SHALL BE IN ACCORDANCE WITH ANSI/ASME Y14.5M-1994. AS50151 CRIMP CONTACT, FRONT AND REAR RELEASE CONNECTORS AND SOLDER CONTACT CONNECTORS ARE INTERMATEABLE. UNLESS OTHERWISE SHOWN, CORRESPONDING FEATURES OF PIN AND SOCKET CONTACT CONNECTORS ARE IDENTICAL. 2. FOR INSERT A
9、RRANGEMENTS SEE MIL-STD-1651. SIZE K .015 L MAX. M +.031 -.000 N +.000 -.062 R S .031 SIZE 16 & 12 CONTS SIZE 8, 4 & 0 CONTS 8S .083 2.031 N/A .562 .532 .504 .496 .729 10S .656 .629 .621 .854 10SL .629 .621 12S .782 .754 .746 .974 12 2.125 .750 .754 .746 14S 2.031 .562 .906 .879 .871 1.099 14 2.125
10、.750 .879 .871 16S 2.031 .562 1.032 1.005 .996 1.224 16 2.125 2.500 .750 1.005 .996 18 .125 1.156 1.131 1.121 1.349 20 1.282 1.256 1.246 1.474 22 1.406 1.381 1.371 1.599 24 .812 1.532 1.506 1.496 1.715 28 1.782 1.756 1.746 1.974 32 .875 2.032 2.007 1.996 2.224 36 2.282 2.257 2.246 2.474 40 2.532 2.5
11、11 2.496 2.724 44 2.782 2.761 2.746 2.974 48 3.032 3.011 2.996 3.224 AEROSPACE STANDARD AS34511 SHEET 3 OF 3 REV. A CONNECTORS, RECEPTACLE, ELECTRIC, CABLE CONNECTING, REAR RELEASE, CRIMP CONTACT, AN TYPE 3. THE PART NUMBERS SHALL BE AS SHOWN IN THE EXAMPLE BELOW: NOTES: NOTICE THIS DOCUMENT REFEREN
12、CES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. SPECIFICATION NOTES: A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE
13、BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. APPLICATION
14、NOTES: 1. AS34511 CLASS K IS CANCELLED AFTER 9 MARCH 1972. CLASS U IS NOT RECOMMENDED FOR NEW DESIGN AND IS NO LONGER RECOMMENDED FOR USE, EXCEPT FOR REPLACEMENT PURPOSES. CLASS L IS RECOMMENDED FOR NEW DESIGN. 2. AS34511 SUPERSEDES MS3451. BASIC PART NO. CLASS L,U,W MATERIAL DESIGNATOR S-STAINLESS STEEL, LEAVE BLANK FOR ALUMINUM ALLOY, WROUGHT ALUMINUM AND FERROUS ALLOY SHELL SIZE INSERT ARRANGEMENT CONTACT DESIGNATOR ALTERNATE INSERT POSITION W, X, Y OR Z. LEAVE BLANK FOR NORMAL POSITION MS3451 W 28 2 P X
