1、AEROSPACE STANDARD CONNECTORS, RECEPTACLE, ELECTRICAL, JAM NUT MOUNTING, REAR RELEASE CRIMP CONTACT, AN TYPE AS34541Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electroni
2、c, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1998-01
3、REAFFIRMED 2003-11 REVISED 2014-05THIRD ANGLE PROJECTION CUSTODIAN: AE-8C1 REV.BFEDERAL SUPPLY CLASS 5935 AS34541SHEET 1 OF 4REV. BPROCUREMENT SPECIFICATION: AS50151SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineeringsciences.
4、The useofthis reportisentirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized,
5、 orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS34541BRATIONALE REVISION IS REQUIRED TO CORRECT DIMENSION “N” FOR SIZE 28. THIS DIMENSION WAS INCORRECTLY LISTED ON T
6、HE AS CONVERSION FROM THE MS DOCUMENT. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS50151. FIGURE 1 - CONNECTOR CONFIGURATION (CLASSES L,U, & W ENVIRONMENT RESISTANT) AEROSPACE STANDARD AS34541SHEET 2 OF 4REV. BC
7、ONNECTORS, RECEPTACLE, ELECTRICAL, JAM NUT MOUNTING, REAR RELEASE CRIMP CONTACT, AN TYPE TABLE 1 - DIMENSIONS SIZEL MAX. M.005 N+.000.005 S.005 SS.005 U.010 SIZE16 & 12 CONTACTSSIZE8 , 4, & 0 CONTACTS8S 2.031 N/A.720.500 1.187 1.272 .687 10S .625 1.312 1.397 .812 10SL .625 1.312 1.397 .812 12S .750
8、1.437 1.522 .937 12 2.125 .970 .750 1.437 1.522 .937 14S 2.031 .720 .870 1.562 1.647 1.125 14 2.125 .970 .870 1.562 1.647 1.125 16S 2.031 .720 1.000 1.687 1.772 1.250 16 2.125 2.500 .970 1.000 1.687 1.772 1.250 18 1.125 1.812 1.897 1.375 20 1.250 1.937 2.022 1.500 22 1.375 2.156 2.241 1.625 24 1.500
9、 2.281 2.366 1.750 28 1.750 2.531 2.616 2.000 32 2.000 2.781 2.866 2.375 36 2.250 3.031 3.116 2.625 40 2.500 3.281 3.366 2.875 44 2.750 3.656 3.741 3.125 48 3.000 3.906 3.991 3.375 TABLE 1 - DIMENSIONS (CONTINUED) SIZEO+.015.000 Z.005 DD .008 O RING PROJECT O RING SIZEA R.P 568 NO. 8S .505 .323 .020
10、020 10S .630 .385 -022 10SL .630 .385 -022 12S .755 .448 -024 12 .755 .448 -024 14S .880 .510 -026 14 .880 .510 -026 16S 1.005 .573 -028 16 1.005 .573 -028 18 1.130 .635 -029 20 1.255 .698 -030 22 1.380 .760 .026-132 24 1.505 .823 -134 28 1.755 .948 -138 32 2.005 1.073 -14236 2.255 1.198 -148 40 2.
11、505 1.323 -15044 2.755 1.448 -152 48 3.005 1.573 -153AEROSPACE STANDARD AS34541SHEET 3 OF 4REV. BCONNECTORS, RECEPTACLE, ELECTRICAL, JAM NUT MOUNTING, REAR RELEASE CRIMP CONTACT, AN TYPE REQUIREMENTS: ALL COMPLETE REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS50151. 1. DESIGN
12、 CONNECTORS SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE 1. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: DECIMALS .016. DIMENSIONS AND TOLERANCING SHALL BE IN ACCORDANCE WITH ANSI/ASME Y14.5M-1994. AS50151 FRONT AND REAR RELEASE CRIMP CONTACT CONNECTORS AND SOLDER CO
13、NTACT CONNECTORS ARE INTERMATEABLE. UNLESS OTHERWISE SHOWN, CORRESPONDING FEATURES OF PIN AND SOCKET CONTACT CONNECTORS ARE IDENTICAL. 2. FOR INSERT ARRANGEMENTS SEE MIL-STD-1651. 3. THE PART NUMBERS SHALL BE AS SHOWN IN THE EXAMPLE BELOW: NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS
14、 CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. SPECIFICATION NOTES: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOU
15、S ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. BASIC PART NO. CLASS L,U,W MATERIAL
16、 DESIGNATOR S-STAINLESS STEEL. LEAVE BLANK FOR ALUMINUM ALLOY, WROUGHT ALUMINUM AND FERROUS ALLOY SHELLSIZEINSERTARRANGEMENT CONTACT DESIGNATOR ALTERNATE INSERT POSITION W, X, Y OR Z. LEAVE BLANK FOR NORMAL POSITION MS3454 L 28 21 P XAEROSPACE STANDARD AS34541SHEET 4 OF 4REV. BCONNECTORS, RECEPTACLE
17、 ELECTRICAL, JAM NUT MOUNTING, REAR RELEASE CRIMP CONTACT, AN TYPE APPLICATION NOTES: 1. AS34541 CLASS K IS CANCELLED AFTER 5 APRIL 1972. CLASS U IS NOT RECOMMENDED FOR NEW DESIGN AND IS NO LONGER RECOMMENDED FOR USE, EXCEPT FOR REPLACEMENT PURPOSES. CLASS L IS RECOMMENDED FOR NEW DESIGN. 2. AS34541 SUPERSEDES MS3454.
