1、 AEROSPACE STANDARD PIN AND PLUG, EXPANSION SET OF PARTS, AL ALLOY 2024-T4 AND 2024-T351, LONG; STD AND .010OVERSIZE DIAMETERS (UNS A92024) AS3589Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any f
2、orm or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: ht
3、tp:/www.sae.org ISSUED 1996-06REVISED 2010-03 REAFFIRMED 2015-04THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.B FEDERAL SUPPLY CLASS 5340AS3589 SHEET 1 OF 2 REV. B PROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of tech
4、nicalandengineering sciences. Theuse ofthisreport is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay ber
5、evised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit bhttp:/www.sae.org/technical/standards/AS3589B RATIONALE AS3589B HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW PO
6、LICY. FIGURE 1 - AS3122 PIN FIGURE 2 - AS3121 PLUG TABLE 1 - PART NUMBERS AEROSPACE STANDARD PART NUMBER /3/ MANUFACTURERSPART NUMBER /3/ PIN PART NUMBER PLUG PART NUMBER APPROX MASS LB/100 AS3589-03 PLGA1561010A AS3122-03 AS3121-03 .043 AS3589-04 PLGA1871010A AS3122-04 AS3121-04 .067 AS3589-05 PLGA
7、2181010A AS3122-05 AS3121-05 .103 AS3589-06 PLGA2501010A AS3122-06 AS3121-06 .168 AS3589-07 PLGA2811010A AS3122-07 AS3121-07 .211 AS3589-08 PLGA3431010A AS3122-08 AS3121-08 .399 AS3589-09 PLGA4061010A AS3122-09 AS3121-09 .635 AS3589-10 PLGA4681010A AS3122-10 AS3121-10 .960 AS3589-11 PLGA5311010A AS3
8、122-11 AS3121-11 1.380 AS3589-12 PLGA6561010A AS3122-12 AS3121-12 2.357 AS3589-53 PLGA1661010A AS3122-03 AS3121-53 (a) .049 AS3589-54 PLGA1971010A AS3122-04 AS3121-54 (a) .073 AS3589-55 PLGA2281010A AS3122-05 AS3121-55 (a) .113 AS3589-56 PLGA2601010A AS3122-06 AS3121-56 (a) .180 AS3589-57 PLGA291101
9、0A AS3122-07 AS3121-57 (a) .229 AS3589-58 PLGA3531010A AS3122-08 AS3121-58 (a) .422 AS3589-59 PLGA4161010A AS3122-09 AS3121-59 (a) .665 AS3589-60 PLGA4781010A AS3122-10 AS3121-60 (a) 1.001 AS3589-61 PLGA5411010A AS3122-11 AS3121-61 (a) 1.435 AS3589-62 PLGA6661010A AS3122-12 AS3121-62 (a) 2.430 (a) D
10、ESIGNATES .010 OVERSIZED PLUG. AEROSPACE STANDARD AS3589 SHEET 2 OF 2 REV. B PIN AND PLUG, EXPANSION SET OF PARTS, AL ALLOY 2024-T4 AND 2024-T351, LONG; STD AND .010 OVERSIZE DIAMETERS (UNS A92024) NOTES: 1. MATERIAL: DASH NUMBERS 03 THROUGH 08 AND 53 THROUGH 58 - AL ALLOY 2024 - T4 PER AMS4120 REF.
11、 DASH NUMBERS 09 THROUGH 12 AND 59 THROUGH 62 - AL ALLOY 2024 - T351 PER AMS4120 REF. 2. FINISH: a. PLUG: ANODIZE PER MIL-A-8625, SEE AS3121 REF. b. PIN: CHEMICAL CONVERSION COATING MIL-DTL-5541, SEE AS3122 REF. /3/ MARK PART NUMBER AND MANUFACTURERS PART NUMBER ON PACKAGE. MARK AS3589-( ) PART NUMB
12、ER AND MANUFACTURERS IDENTIFICATION ON PACKAGE IN ACCORDANCE WITH AS478, METHOD 37. 4. SEE AIR3276 FOR HOLE PREPARATION AND AIR3277 FOR INSTALLATION PROCEDURE. 5. PIN AND PLUG EXPANSION SET OF PARTS SHALL CONTAIN A PIN SIZE FROM AS3122 AND A PLUG SIZE FROM AS3121 AS SPECIFIED WITH THE CORRESPONDING
13、DASH NUMBER IN TABLE 1. 6. AS, AIR AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. MIL IS AN US GOVERNMENT PUBLICATION. 7. A CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS I
14、SSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. APPROVED SOURCE OF SUPPLY: THE LEE CO
15、WESTBROOK, CT FEDERAL SUPPLY CODE FOR MANUFACTURERS NO 92555. ONLY THE ITEM DESCRIBED ON THIS DRAWING WHEN PROCURED FROM THE VENDOR LISTED HEREON IS APPROVED FOR USE IN THE APPLICATIONS SPECIFYING THIS AEROSPACE STANDARD IDENTIFICATION NUMBER. A SUBSTITUTE ITEM SHALL NOT BE USED WITHOUT PRIOR TESTING AND APPROVAL BY THE DESIGN ACTIVITY RESPONSIBLE FOR THE APPLICATION. IDENTIFICATION OF THE APPROVED SOURCE HEREON IS NOT TO BE CONSTRUED AS A GUARANTEE OF PRESENT OR CONTINUED AVAILABILITY AS A SOURCE OF SUPPLY FOR THE ITEM DESCRIBED ON THE DRAWING.
