1、 AEROSPACE STANDARD TEE, BULKHEAD ON RUN, STANDARD AND REDUCER, REDUCED BODY, FLARELESS AS4134Copyright 2016 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photoco
2、pying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED1992-11 REVISED2016-05THIRD AN
3、GLE PROJECTION CUSTODIAN: G-3/G-3B REV.C FEDERAL SUPPLY CLASS 4730 AS4134 SHEET 1 OF 4 REV. C PROCUREMENT SPECIFICATION: AS18280, SEE NOTE 4 SAE Technical Standards BoardRules providethat:“This reportis published bySAEto advance the state oftechnicaland engineering sciences. The use of this reportis
4、entirely voluntary, andits applicability andsuitability for any particularuse, includingany patentinfringement arising therefrom,is the sole responsibility of theuser.”SAE reviews eachtechnical reportatleast every fiveyears atwhichtimeitmay berevised,reaffirmed, stabilized,orcancelled. SAE invites y
5、ourwrittencomments andsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS4134C RATIONALE CORRECT TYPOGRAPHICAL ERROR IN TABLE 4. FIGURE 1 - TEE, BULKHEAD ON RUN, REDUCED BODY, FLARELESS AEROSPACE STANDARD AS4134 SHEET
6、 2 OF 4 REV. C TEE, BULKHEAD ON RUN, STANDARD AND REDUCER, REDUCED BODY, FLARELESS TABLE 1 - DIMENSIONS AND WEIGHTS BASIC NO. AS4134 /19/ SIZE CODE H MIN J P .030 LB/EA APPROX REF CRES LB/EA APPROX REF TI 04 .050 .390 .030 .082 .047 05 .050 .453 .159 .109 .061 06 .050 .453 .137 .113 .065 08 .050 .57
7、7 .140 .211 .121 10 .070 .702 .157 .364 .208 12 .080 .890 .166 .531 .305 16 .090 1.140 .174 .732 .421 20 .110 1.390 .071 1.507 .873 24 .130 1.640 - 1.959 1.133 TABLE 2 - FITTING END SIZE CODE TUBE OD T THREAD PER AS8879 CLASS 3A D E 04 .250 .4375-20UNJF .371 .350 05 .313 .5000-20UNJF .371 .412 06 .3
8、75 .5625-18UNJF .379 .453 08 .500 .7500-16UNJF .461 .577 10 .625 .8750-14UNJF .511 .702 12 .750 1.0625-12UNJF .556 .890 16 1.000 1.3125-12UNJ .556 1.140 20 1.250 1.6250-12UNJ .556 1.390 24 1.500 1.8750-12UNJ .556 1.640 TABLE 3 - LEG LENGTH A FORGING SIZE 04 05 06 08 10 12 16 20 24 04 1.523 - - - - -
9、 - - - 05 1.555 1.555 - - - - - - - 06 1.665 1.665 1.711 - - - - - - 08 1.774 1.774 1.820 1.992 - - - - - 10 1.914 1.914 1.960 2.132 2.273 - - - - 12 2.024 2.024 2.070 2.242 2.383 2.492 - - - 16 2.149 2.149 2.195 2.367 2.508 2.617 2.617 - - 20 2.430 2.430 2.476 2.648 2.789 2.898 2.898 2.898 - 24 2.7
10、12 2.712 2.758 2.930 3.071 3.180 3.180 3.180 3.180 AEROSPACE STANDARD AS4134 SHEET 3 OF 4 REV. C TEE, BULKHEAD ON RUN, STANDARD AND REDUCER, REDUCED BODY, FLARELESS TABLE 4 - LEG LENGTH B FORGING SIZE 04 05 06 08 10 12 16 20 24 04 .961 - - - - - - - - 05 1.055 1.055 - - - - - - - 06 1.070 1.070 1.08
11、6 - - - - - - 08 1.227 1.227 1.243 1.336 - - - - - 10 1.352 1.352 1.368 1.461 1.524 - - - - 12 1.414 1.414 1.430 1.523 1.586 1.649 - - - 16 1.507 1.507 1.523 1.616 1.679 1.742 1.742 - - 20 1.788 1.788 1.804 1.897 1.960 2.023 2.023 2.023 - 24 1.976 1.976 1.992 2.085 2.148 2.211 2.211 2.211 2.211 NOTE
12、S: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. /1/ MATERIAL a. CODE LETTER J: TYPE 304 CORROSION RESISTANT STEEL PER AMS5639 b. CODE LETTER T: TYPE 6AL-4V TITANIUM ALLOY PER AMS4928 c. COD
13、E LETTER V: TYPE 15-5PH CORROSION RESISTANT STEEL PER AMS5659 2. HEAT TREATMENT a. MATERIAL CODE LETTER J: NONE b. MATERIAL CODE LETTER T: NONE c. MATERIAL CODE LETTER V: HEAT TREAT TO CONDITION H-1075 PER AMS2759/3 /3/ FINISH a. MATERIAL CODE LETTER J: PASSIVATE PER AMS2700 TYPE 6 OR 7 b. MATERIAL
14、CODE LETTER T: FLUORIDE PHOSPHATE CONVERSION COAT PER AMS2486 c. MATERIAL CODE LETTER V: (1) NO SUFFIX FINISH CODE LETTER: PASSIVATE PER AMS2700 TYPE 2 OR 8 (2) SUFFIX FINISH CODE LETTER “P”; CADMIUM PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2 /4/ PROCUREMENT SPECIFICATION: AS18280 UNLESS SPECIFIED OTH
15、ERWISE ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS18280 FOR THIS STANDARD. SEE http:/www.eAuditN FOR CURRENT QPL ONLINE. /5/ IDENTIFICATION AT
16、 LOCATION SHOWN: MARK PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, OR 15B. a. FOR SIZES 06 (.375 OD TUBE SIZE) AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTERS “AS”, MATERIAL CODE LETTER AND FORGING MANUFACTURERS IDENTIFICATION WHEN MADE FROM FORGING b. FOR SIZES 08 (.500 OD TUBE SIZE
17、) AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER, MATERIAL CODE LETTER AND FORGING MANUFACTURERS IDENTIFICATION WHEN MADE FROM FORGING AEROSPACE STANDARD AS4134 SHEET 4 OF 4 REV. C TEE, BULKHEAD ON RUN, STANDARD AND REDUCER, REDUCED BODY, FLARELESS 6. THIS PART IS INTENDED
18、 FOR USE IN SYSTEMS WITH OPERATING PRESSURES AS FOLLOWS: a. SIZES -04 THROUGH -16 AT 3000 PSI b. SIZES -20 AND -24 AT 1500 PSI NOTE: OPERATING PRESSURES HAVE BEEN CHANGED FROM 4000 PSI AND 2000 PSI TO 3000 PSI AND 1500 PSI TO COMPLY WITH AS18280 SYSTEM PRESSURE REQUIREMENTS. USERS OF THIS STANDARD F
19、OR 4000 PSI SYSTEM APPLICATIONS ARE ADVISED TO CONTROL SOURCE APPROVAL BY STANDARD PAGE SUPPLEMENT OR SIMILAR MEANS. /7/ FOR SHOULDER DIAMETER ON BULKHEAD REDUCERS: a. USE “S” DIAMETER (OF AS4377) FOR SMALLER BULKHEAD END SIZE ON ONE STEP REDUCTIONS (E.G., 08 FORGING TO 06 BULKHEAD END, USE “S” FOR
20、06 BULKHEAD AS SHOULDER DIAMETER) b. USE “J” OF FORGING FOR TWO STEP OR GREATER REDUCTIONS (E.G., 08 FORGING TO 04 BULKHEAD END, USE “J” DIAMETER FOR 08 FORGING AS SHOULDER DIAMETER) 8. WHEN MACHINED FROM BAR OR OVERSIZED FORGING, THE CENTER BODY SECTION SHALL CONFORM TO AS1376, TABLE 2. /9/ RADIUS
21、APPLICABLE TO TITANIUM PARTS ONLY. 10. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 11. THIS PART IS A REDUCED BODY VERSION OF MS21912 IF NONREDUCER, OR AS1003 IF REDUCER. /12/ SPECIFY END SIZES IN THIS ORDER: BULKHEAD END FIRST (PORT #1), OPPOSITE END SECOND (PORT #2), SIDE PORT THIRD (PORT
22、 #3). 13. LARGEST END DETERMINES FORGING SIZE. /14/ APPLICABLE ONLY TO REDUCERS AND SIZE 04 AND 05 NONREDUCERS. 15. INTERPRETATION OF DRAWING PER ARP4296. 16. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES R
23、a. 17. DIMENSIONS AND TOLERANCING: ANSI Y14.5M-1982 18. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS .5q. /19/ EXAMPLE OF PART NUMBER: 20. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN
24、 LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICAT
25、IONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 21. INVENTORIED PARTS CONFORMING TO THE PREVIOUS LETTER CHANGE MAY BE USED TO DEPLETION. SIZE CODE, TUBE SIZE OF PORT #3 IN .062 INCH INCREMENTS /12/ SIZE CODE, TUBE SIZE OF PORT #2 IN .062 INCH INCREMENTS /12/ SIZE CODE, TUBE SIZE OF PORT #1 IN .062 INCH INCREMENTS /12/
