1、 AEROSPACE STANDARD FITTING, TEE, BULKHEAD ON RUN, SHORT FLARELESS AS4672Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or
2、otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED1992-07REAFFIRMED 2004-07REVISED 2017-08THIRD ANGLE
3、 PROJECTION CUSTODIAN: G-3/G-3B REV.D FEDERAL SUPPLY CLASS 4730 AS4672 SHEET 1 OF 3 REV. D PROCUREMENT SPECIFICATION: AS18280 /4/ SAE Technical Standards Board Rules provide that: “This report is published by SAEtoadvance thestate of technicaland engineering sciences. The useof this report is entire
4、ly voluntary, and its applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,is thesole responsibility of theuser.” SAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed, stabilized, or cancelled. SAE invites
5、 your written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS4672D RATIONALE ADDED CONDUCTIVE HIGH PURITY ALUMINUM COATING FOR ALUMINUM ALLOY FITTINGS. FIGURE 1 FITTING, TEE TABLE 1 DIMENSIONS AND WEIGHTS BASIC NO.
6、 AS4672 /9/ /18/ SIZE CODE (NOMINAL TUBE SIZE) T THREAD PER AS8879 CLASS 3A A B D H J +.005/-.020 LB/EA APPROX REF ALUM LB/EA APPROX REF CRES LB/EA APPROX REF TI 20 1.250 1.5625-12UNJ 1.798 2.686 .517 .122 1.375 .474 1.316 .752 24 1.500 1.8125-12UNJ 1.986 2.968 .614 .154 1.688 .700 1.941 1.109 AEROS
7、PACE STANDARD AS4672 SHEET 2 OF 3 REV. D FITTING, TEE, BULKHEAD ON RUN, SHORT FLARELESS NOTES NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. /1/ MATERIAL a. CODE LETTER T: TYPE 6AL-4V TITANIU
8、M ALLOY FORGING OR BAR PER AMS4928 b. CODE LETTER V: TYPE 15-5PH CORROSION RESISTANT STEEL FORGING OR BAR PER AMS5659 c. CODE LETTER W: TYPE 7075-T73 ALUMINUM ALLOY FORGING PER AMS4141 OR TYPE 7075-T7351 ALUMINUM ALLOY BAR PER AMS4124 2. HEAT TREATMENT a. MATERIAL CODE LETTER T: NONE b. MATERIAL COD
9、E LETTER V: HEAT TREAT TO CONDITION H-1075 PER AMS2759/3 c. MATERIAL CODE LETTER W: NONE /3/ FINISH a. MATERIAL CODE LETTER T - FLUORIDE PHOSPHATE CONVERSION COAT PER AMS2486 b. MATERIAL CODE LETTER V: (1) V CODE PARTS TO BE PASSIVATED ONLY WILL HAVE NO FINISH CODE LETTER AFTER THE SIZE CODE IN THE
10、PART NUMBER. THE FINISH WILL BE: PASSIVATE PER AMS2700 TYPE 2 OR 8. (2) V CODE PARTS TO BE CADMIUM PLATED ONLY WILL HAVE THE FINISH CODE LETTER “P” AFTER THE SIZE CODE IN THE PART NUMBER. THE FINISH WILL BE: CADMIUM PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2. c. MATERIAL CODE LETTER W: (1) W CODE PART
11、S TO BE ANODIZED ONLY WILL HAVE NO FINISH CODE LETTER AFTER THE SIZE CODE IN THE PART NUMBER. THE FINISH WILL BE ANODIZE PER AMS2472 OR PER MIL-A-8625, TYPE II, CLASS 2 DYED BROWN, SIMILAR TO COLOR 10080 OF AMS-STD-595. (2) W CODE PARTS TO BE COATED WITH HIGH PURITY ALUMINUM ONLY WILL HAVE THE FINIS
12、H CODE LETTER “V” AFTER THE SIZE CODE IN THE PART NUMBER. SEE PROCUREMENT SPECIFICATION FOR REQUIREMENTS. /4/ PROCUREMENT SPECIFICATION: AS18280 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMAN
13、CE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS18280 FOR THIS STANDARD. SEE www.eAuditN FOR CURRENT QPL ONLINE. /5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, OR 15B. MANUFACTURERS NAME, TRADEMARK OR CAGE CODE, BASIC PART NUMBER, AND MATERIA
14、L CODE LETTER. 6. INTENDED USE: THIS PART IS DESIGNED FOR USE IN TUBING CONNECTION SYSTEMS WITH OPERATING PRESSURES AS FOLLOWS: a. SIZES -20 AND -24 TITANIUM ALLOY AND CORROSION RESISTANT STEEL AT 3000 PSI b. SIZES -20 AND -24 ALUMINUM ALLOY AT 600 PSI 7. WHEN MACHINED FROM BAR OR OVERSIZED FORGINGS
15、 THE CENTER BODY SECTION SHALL CONFORM TO AS1376 TABLE 10. /8/ RADIUS APPLICABLE FOR TITANIUM PARTS ONLY. /9/ THIS IS A NON-REDUCER FITTING. ALL PORTS OF ANY GIVEN PART WILL BE THE SAME SIZE. FOR REDUCERS USE AS4689. AEROSPACE STANDARD AS4672 SHEET 3 OF 3 REV. D FITTING, TEE, BULKHEAD ON RUN, SHORT
16、FLARELESS /10/ FINISH CODE LETTER “P” SHALL BE PLACED AFTER SIZE CODES ONLY FOR MATERIAL CODE “V” PARTS THAT ARE TO BE CADMIUM PLATED. FINISH CODE LETTER “V” SHALL BE PLACED AFTER SIZE CODES ONLY FOR MATERIAL CODE “W” PARTS. 11. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR
17、THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE
18、 NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 12. INVENTORIED PARTS CONFORMING TO THE PREVIOUS “LETTER CHANGE” MAY BE USED TO DEPLETION. 13. INTERPRETATION OF DRAWING PER AS4296. 14. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UN
19、LESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES Ra. FORGED SURFACES MAY BE 250 MICROINCHES Ra. 15. BREAK EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 16. DIMENSIONING AND TOLERANCING: ANSI Y14.5M-1982. 17. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 5 DEGREES. /18/ EXAMPLE OF PART NUMBER:
