1、 AEROSPACE STANDARD FITTING, ELBOW, 90, EXTERNAL SWAGE, HYDRAULIC AS5009Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or o
2、therwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1997-11REAFFIRMED2015-04THIRD ANGLE PROJECTION CUST
3、ODIAN: G-3/G-3B FEDERAL SUPPLY CLASS 4730AS5009 SHEET 1 OF 2 PROCUREMENT SPECIFICATION: /5/ AS4459SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport is entirelyvoluntary, andits applicability a
4、nd suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SA
5、E values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS5009 RATIONALE AS5009 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. FIGURE 1 - ELBOW, 90, EXTERNAL SWAGETABLE 1 - DIMENSIONS AND WEIGHTSBASIC NO.AS5009/14/SIZE
6、 CODENOMINALTUBESIZEA+.030.000B.015C+.000.003D+.030.000 EF+.030.000 GV/2/ AALB/EAMAXCRESLB/EAMAXTILB/EAMAXAL03 .188 .860 .325 .275 .860 .182/.187 .715 .195/ .198 .170/.220 .13 .0140 .00800 .0050004 .250 1.050 .390 .338 1.050 .244/.249 .915 .257/ .260 .190/.240 .22 .0250 .0140 .0090005 .312 1.120 .46
7、5 .413 1.120 .303/.308 .955 .319/ .322 .200/.250 .22 .0330 .0190 .011006 .375 1.190 .545 .480 1.190 .366/.371 .990 .382/ .385 .220/.270 .22 .048 .0270 .016008 .500 1.755 .705 .655 1.755 .482/.489 1.493 .508/ .511 .410/.435 .50 .116 .0660 .040010 .625 1.860 .861 .787 1.860 .606/.614 1.533 .633/ .636
8、410/.435 .50 .167 .0950 .057012 .750 1.990 1.036 .929 1.990 .731/.739 1.603 .758/ .761 .365/.390 .50 .234 .134 .081016 1.000 2.344 1.380 1.257 2.344 .981/.989 1.748 1.008/1.011 .325/.350 .50 .541 .307 .185AEROSPACE STANDARD AS5009 SHEET 2 OF 2 FITTING, ELBOW, 90, EXTERNAL SWAGE, HYDRAULIC NOTES:/1/
9、 MATERIAL:a. CODE LETTER “”: 21-6-9 CRES BAR PER AMS 5656b. CODE LETTER “E”: COMMERCIALLY PURE TITANIUM BAR PER AMS 4921c. CODE LETTER “D”: 6061T6 ALUMINUM ALLOY PER AMS 4150/2/ FINISH:a. MATERIAL CODE “”: PASSIVATE PER QQ-P-35 TYPE VII, PTFE COAT (COLOR GREEN) BORE DIAMETER TO “V” DEPTH, OVERSPRAY
10、ON “Y” PERMISSIBLE.b. MATERIAL CODE “E”: PTFE COAT (COLOR BLACK) EXTERIOR SURFACES AND BORE DIAMETER TO “V” DEPTH UNLESS OTHERWISE SPECIFIED, SEE NOTE /14/. AA TO BE FREE OF PTFE COATING.c. MATERIAL CODE “D”: CHEMICAL FILM FINISH ENTIRE PART (INCLUDING INTERNAL DIAS) PER MIL-C-5541, CLASS 1A, PTFE C
11、OAT (GREEN) EXTERNAL SURFACE AND BORE DIAMETER TO “V” DEPTH.3. LIQUID PENETRANT INSPECT PER ASTM E 1417 TYPE 1 SENSITIVITY 2. LINEAR INDICATIONS PROHIBITED, ROUNDED INDICATIONS ACCEPTABLE./4/ FILL OUTER GROOVE FOR CRES AND TITANIUM WITH SILICONE. FILL ALL GROOVES FOR ALUMINUM WITH SILICONE ELASTOMER
12、/5/ THIS PART SHALL BE QUALIFIED TO THE PROCUREMENT SPECIFICATION IN A COMPLETE ASSEMBLY. USERS OF THIS STANDARD ARE ADVISED TO CONTROL SOURCE APPROVAL(S) BY STANDARD PAGE SUPPLEMENT SHEET OR SIMILAR MEANS.6. SPECIFIC DIMENSIONS AND TOLERANCES NOT DEFINED ON THIS STANDARD SHALL BE SPECIFIED AND CON
13、TROLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO ENSURE COMPLIANCE WITH THE PROCUREMENT SPECIFICATION./7/ IDENTIFICATION: PARTS SHALL BE IDENTIFIED IN THE AREA SHOWN PER AS4459.8. INTENDED USE: PER AS4459.9. INTERPRETATION OF DRAWING PER ARP4296.10. SURFACE TEXTURE: SYMBOLS PER ANSI Y
14、14.36; REQUIREMENTS PER ANSI/ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 m Ra.11. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED.12. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994.13. DIMENSIONS IN INCHES; UNLESS OTHERWISE SPECIFIED, TOLERANCES: DIMENSIONS LINEAR .010,ANGULAR 2./14/
