1、Copyright 2003 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, orotherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT
2、ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA)Fax: 724-776-0790 Email: custsvcsae.org SAE WEB ADDRESS: http:/www.sae.orgSAE Technical Standards Board Rules providethat: “This report is published by SAE to advancethe state oftechnical and engineering sciences.Theuse
3、ofthis reportisentirelyvoluntary, andits applicabilityand suitabilityfor any particularuse,including any patentinfringement arising therefrom,isthe sole responsibility of the user.”SAE reviews each technical reportatleastevery five years atwhich timeitmay bereaffirmed,revised, or cancelled.SAE invit
4、es yourwritten comments and suggestions.SHEET 1 OF 3AS5165REV.ATHIRD ANGLE PROJECTIONAEROSPACE STANDARDAS5165REV.AISSUED 2000-07 REVISED 2003-08FITTING, CONNECTOR, MULTIPLEFLUID PRESSURE LINE, TEECUSTODIAN: SAE G-3/G-3B PROCUREMENT SPECIFICATION: /4/ AS4875/1FEDERAL SUPPLY CLASS 4730FIGURE 1 - FITTI
5、NG, CONNECTOR, TEECopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-FITTING, CONNECTOR, MULTIPLEFLUID PRESSURE LINE, TEEAEROSPACE STANDARDAS5165SHEET 2 OF 3AS5165REV.AREV. ANOTES:/1/ MATERIAL:a. DASH AS
6、CODE LETTER - TYPE 4130 CARBON STEEL FORGING OR BAR PER AMS-S-6758 OR AMS 6370; OR TYPE 4140 PER AMS 6382. /2/b. CODE LETTER D - TYPE 2014-T6 ALUMINUM ALLOY FORGING PER AMS 4133; OR TYPE 2024-T6 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6 OR TYPE 2024-T851 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6 OR AMS 4339
7、. /2/c. CODE LETTER J - TYPE 304 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AMS 5639.d. CODE LETTER K - TYPE 316 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AMS 5648.e. CODE LETTER R - TYPE 321 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AMS 5645.f
8、. CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY FORGING OR BAR PER AMS 4928.g. CODE LETTER W - TYPE 7075-T73 ALUMINUM ALLOY FORGING PER AMS 4141; OR TYPE 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9; OR TYPE 7075-T7351 ALUMINUM ALLOY BAR PER AMS 4124. /2/2/ HEAT TREATMENT:a. DASH AS CODE LETTER - SEE
9、 HARDNESS REQUIREMENT PER PROCUREMENT SPECIFICATION.b. CODE LETTERS D AND W - SEE ELECTRICAL CONDUCTIVITY AND HARDNESS REQUIREMENT PER PROCUREMENT SPECIFICATION.c. OTHER CODE LETTERS - NONE.TABLE 1A - DIMENSIONSBASIC NO.AS5165/13/SIZE CODE(NOMINALTUBESIZE)T THREADPERAS8879CLASS 3AA.023C.005D.005 EF.
10、00104 .250 .4375-20 UNJF 1.148 .692 .474 .562 .43905 .312 .5000-20 UNJF 1.148 .755 .536 .625 .50106 .375 .5625-18 UNJF 1.273 .817 .599 .750 .56408 .500 .7500-16 UNJF 1.460 1.005 .786 .937 .75110 .625 .8750-14 UNJF 1.680 1.130 .911 1.125 .87612 .750 1.0625-12 UNJ 2.023 1.318 1.099 1.375 1.06316 1.000
11、 1.3125-12 UNJ 2.398 1.568 1.349 1.687 1.313TABLE 1B - DIMENSIONS AND WEIGHTSBASIC NO.AS5165/13/SIZE CODE GH.010 K VLB/EAAPPROX.REFALLB/EAAPPROX.REFSTEELLB/EAAPPROX.REFTI04 .437 .750 .375 .797- .815 .0334 .0958 .052805 .437 .750 .500 .797- .815 .0301 .0863 .047606 .500 .875 .500 .985-1.003 .0492 .14
12、1 .077908 .500 1.125 .750 1.173-1.191 .0822 .236 .13010 .625 1.375 .812 1.355-1.380 .130 .374 .20612 .625 1.625 1.000 1.668-1.693 .224 .642 .35416 .812 2.125 1.500 2.042-2.072 .366 1.05 .580Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking
13、permitted without license from IHS-,-FITTING, CONNECTOR, MULTIPLEFLUID PRESSURE LINE, TEEAEROSPACE STANDARDAS5165SHEET 3 OF 3AS5165REV.AREV. A3. FINISH:a. DASH AS CODE LETTER - CADMIUM PLATE PER QQ-P-416, TYPE II, CLASS 2, DYE BLACK AND COAT WITH A LIGHT FILM OF OIL PER PROCUREMENT SPECIFICATION.b.
14、CODE LETTER D - ANODIZE PER AMS 2472 OR MIL-A-8625, TYPE II, CLASS 2, DYE BLUE, DUPLEX SEAL PER PROCUREMENT SPECIFICATION.c. CODE LETTERS J, K, AND R - PASSIVATE PER AMS-QQ-P-35, TYPE VI OR VII.d. CODE LETTER T - ANODIZE PER AMS 2488 OR FLUORIDE PHOSPHATE CONVERSION COAT PER AMS 2486 WITH COLOR PER
15、PROCUREMENT SPECIFICATION.e. CODE LETTER W - ANODIZE PER MIL-A-8625, TYPE II, CLASS 2, DYE BROWN, DUPLEX SEAL PER PROCUREMENT SPECIFICATION./4/ PROCUREMENT SPECIFICATION: AS4875/1 EXCEPT AS SPECIFIED ON THIS STANDARD. USERS OF THIS STANDARD SHALL PROCURE THIS PRODUCT FROM ACCREDITED MANUFACTURER(S)
16、OR ACCREDITED DISTRIBUTOR(S) AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED MANUFACTURERS LIST (QML) FOR THIS TYPE PRODUCT./5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, OR 15B.a. FOR SIZE 06 AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMA
17、RK, LETTERS “AS” AND MATERIAL CODE LETTER.b. FOR SIZE 08 AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER AND MATERIAL CODE LETTER.6. INTENDED USE: THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH MAXIMUM OPERATING PRESSURES AS FOLLOWS:a. SIZES 04 THROUGH 12 IN ALUMINUM ALLOY A
18、ND SIZES 04 THROUGH 16 IN CORROSION RESISTANT STEEL AND TITANIUM ALLOY AT 3000 psi.b. SIZE 16 IN ALUMINUM ALLOY AT 1500 psi.THIS STANDARD IS THE FUNCTIONAL EQUIVALENT OF AN779 AND IS INTENDED TO BE SUITABLE AS A REPLACEMENT STANDARD.7. WHEN MACHINED FROM BAR OR OVERSIZED FORGINGS, THE CENTER BODY SE
19、CTION SHALL CONFORM TO AS1376, TABLE 8.8. INTERPRETATION OF DRAWING PER ARP4296.9. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. FORGED SURFACES MAY BE 250 in Ra.10. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPE
20、CIFIED.11. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994.12. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS 030./13/ EXAMPLE OF PART NUMBER:14. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AR
21、EAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-
