1、AEROSPACE STANDARD FITTING, TEE, STANDARD AND REDUCER, BULKHEAD ON RUN, INTERNAL ON SIDE, FLARED, 37 SPHERICAL AS6098Copyright 2011 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electron
2、ic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2011-0
3、5THIRD ANGLE PROJECTION CUSTODIAN: SAE G-3/G-3B FEDERAL SUPPLY CLASS 4730 AS6098SHEET 1 OF 5PROCUREMENT SPECIFICATION: /4/ AS6076SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely v
4、oluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomme
5、nts andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS6098RATIONALE THIS SAE AEROSPACE STANDARD (AS) ESTABLISHES THE REQUIREMENTS FOR A BULKHEAD TEE FITTING WITH 37 DEGREES SPHERICAL FLARED TUBE. FIGURE 1 - FITTIN
6、G, TEE, BULKHEAD END PORT #3 SHOWN AS NON-REDUCER FIGURE 2 - FITTING, TEE, BULKHEAD END PORT #3 SHOWN AS REDUCER SAME AS FIGURE 1 EXCEPT AS SHOWN AEROSPACE STANDARD AS6098SHEET 2 OF 5FITTING, TEE, STANDARD AND REDUCER, BULKHEAD ON RUN, INTERNAL PORT ON SIDE, FLARED, 37 SPHERICAL TABLE 1 DIMENSIONS A
7、ND WEIGHTS /16/ BASIC NO. AS6098/20/SIZE CODE E/10/F/10/ V W Z/12/LB/EAAPPROX. REF ALUMLB/EAAPPROX. REF CRESLB/EAAPPROX. REF TI02 .648 - .485- .502 .090 .562 .0348 .0998 .0551 03 .711 - .547- .565 .100 .625 .0456 .131 .0722 04 .773 .375 .735- .753 .110 - .0930 .267 .147 05 .773 .375 .735- .753 .120
8、- .0895 .257 .142 06 .836 .375 .860- .878 .120 - .134 .386 .213 08 1.023 .469 1.047-1.065 .150 - .214 .617 .340 10 1.180 .625 1.047-1.065 .170 1.125 .221 .636 .351 12 1.367 .688 1.292-1.317 .185 1.375 .365 1.05 .579 16 1.555 .719 1.605-1.630 .205 1.625 .527 1.51 .835 20 1.742 .781 1.855-1.880 .240 1
9、.938 .759 2.18 1.20 TABLE 2 LEG LENGTH B FORGING SIZE/11/TUBESIZE OF PORT #1 02TUBESIZE OF PORT #1 03TUBESIZE OF PORT #1 04TUBESIZE OF PORT #1 05TUBESIZE OF PORT #1 06TUBESIZE OF PORT #1 08TUBESIZE OF PORT #1 10TUBESIZE OF PORT #1 12TUBESIZE OF PORT #1 16TUBESIZE OF PORT #1 2002 1.491 - - - - - - -
10、- - 03 1.523 1.523 - - - - - - - - 04 1.679 1.679 1.773 - - - - - - - 05 1.679 1.679 1.773 1.773 - - - - - - 06 1.851 1.851 1.945 1.945 2.023 - - - - - 08 1.851 1.851 1.945 1.945 2.023 2.179 - - - - 10 1.929 1.929 2.023 2.023 2.101 2.257 2.398 - - - 12 2.008 2.008 2.102 2.102 2.180 2.336 2.477 2.648
11、 - - 16 2.227 2.227 2.321 2.321 2.399 2.555 2.696 2.867 2.867 - 20 2.367 2.367 2.461 2.461 2.539 2.695 2.836 3.007 3.007 3.054 TABLE 3 LEG LENGTH D FORGING SIZE/11/TUBESIZE OF PORT #2 02TUBESIZE OF PORT #2 03TUBESIZE OF PORT #2 04TUBESIZE OF PORT #2 05TUBESIZE OF PORT #2 06TUBESIZE OF PORT #2 08TUBE
12、SIZE OF PORT #2 10TUBESIZE OF PORT #2 12TUBESIZE OF PORT #2 16TUBESIZE OF PORT #2 2002 .929 - - - - - - - - - 03 .961 .992 - - - - - - - - 04 1.109 1.140 1.211 - - - - - - - 05 1.109 1.140 1.211 1.211 - - - - - - 06 1.165 1.196 1.267 1.267 1.273 - - - - - 08 1.232 1.283 1.354 1.354 1.360 1.461 - - -
13、 - 10 1.338 1.369 1.440 1.440 1.446 1.547 1.648 - - - 12 1.420 1.451 1.522 1.522 1.528 1.629 1.730 1.836 - - 16 1.623 1.654 1.725 1.725 1.731 1.832 1.933 2.039 2.086 - 20 1.763 1.794 1.865 1.865 1.871 1.972 2.073 2.179 2.226 2.273 AEROSPACE STANDARD AS6098SHEET 3 OF 5FITTING, TEE, STANDARD AND REDUC
14、ER, BULKHEAD ON RUN, INTERNAL PORT ON SIDE, FLARED, 37 SPHERICAL TABLE 4 G /13/ FORGING SIZE/11/TUBESIZE OF PORT #3 02TUBESIZE OF PORT #3 03TUBESIZE OF PORT #3 04TUBESIZE OF PORT #3 05TUBESIZE OF PORT #3 06TUBESIZE OF PORT #3 08TUBESIZE OF PORT #3 10TUBESIZE OF PORT #3 12TUBESIZE OF PORT #3 1603 - -
15、 - - - - - - - 04 .594 .656 - - - - - - - 05 .594 .656 - - - - - - - 06 .594 .656 .719 .781 - - - - - 08 .594 .656 .719 .781 .844 - - - - 10 .594 .656 .719 .781 .844 - - - - 12 .594 .656 .719 .781 .844 1.062 - - - 16 .594 .656 .719 .781 .844 1.062 1.188 1.438 - 20 .594 .656 .719 .781 .844 1.062 1.18
16、8 1.438 1.688 TABLE 5 TUBE SIZE AND CORRESPONDING THREAD PORT SIZE(NOMINAL TUBESIZE)T THREAD PER AS8879 CLASS 3A 02 .125 .3125-24 UNJF 03 .188 .3750-24 UNJF04 .250 .4375-20 UNJF 05 .312 .5000-20 UNJF 06 .375 .5625-18 UNJF08 .500 .7500-16 UNJF 10 .625 .8750-14 UNJF 12 .750 1.0625-12 UNJ16 1.000 1.312
17、5-12 UNJ 20 1.250 1.6250-12 UNJ NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. /1/ MATERIAL: a. CODE LETTER F - TYPE 4130 CARBON STEEL FORGING OR BAR PER AMS-S-6758 OR AMS6370; OR TYPE 4140
18、PER AMS6382. b. CODE LETTER J - TYPE 304 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AMS5639. c. CODE LETTER K - TYPE 316 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AMS5648. d. CODE LETTER R - TYPE 321 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AM
19、S5645. e. CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY FORGING OR BAR PER AMS4928. f. CODE LETTER W - TYPE 7075-T73 ALUMINUM ALLOY FORGING PER AMS4141; OR TYPE 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9; OR TYPE 7075-T7351 ALUMINUM ALLOY BAR PER AMS4124. AEROSPACE STANDARD AS6098SHEET 4 OF 5FITTIN
20、G, TEE, STANDARD AND REDUCER, BULKHEAD ON RUN, INTERNAL PORT ON SIDE, FLARED, 37 SPHERICAL 2. HEAT TREATMENT: a. MATERIAL CODE LETTER F- HARDNESS SHALL BE 92 HRC PER PROCUREMENT SPECIFICATION. b. OTHER MATERIAL CODE LETTERS - NONE. 3. FINISH: a. MATERIAL CODE LETTER F - CADMIUM PLATE PER AMS-QQ-P-41
21、6, TYPE II, CLASS 2, DYE BLACK. b. MATERIAL CODE LETTERS J, K, AND R - PASSIVATE PER AMS2700, TYPE 6 OR 7. c. MATERIAL CODE LETTER T - FLUORIDE PHOSPHATE CONVERSION COAT PER AMS2486 OR ANODIZE PER AMS2488 TYPE 2. d. MATERIAL CODE LETTER W: 1. ANODIZE PER AMS2472 OR MIL-A-8625, TYPE II, CLASS 2, DYE
22、BROWN, DUPLEX SEAL PER PROCUREMENT SPECIFICATION. 2. W CODE PARTS TO BE COATED WITH HIGH PURITY ALUMINUM ONLY WILL HAVE THE FINISH CODE LETTER “V” AFTER THE SIZE CODE IN THE PART NUMBER. HIGH PURITY ALUMINUM COAT PER PROCUREMENT SPECIFICATION. /4/ PROCUREMENT SPECIFICATION: AS6076 EXCEPT AS SPECIFIE
23、D ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE NATIONAL AEROSPACE AND DEFENSE CONTRACTORS ACCREDITATION PROGRAM (NADCAP) QUALIFIED MANUFACTURER LIST (QML) FOR THIS PRODUCT TYPE. THE QML IS AVAILABLE AT ./5/ IDENTIFICATION
24、AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D, OR METHOD 7A3, 15A3, OR 15B. a. FOR SIZE 06 AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTER “AS” AND MATERIAL CODE LETTER. b. FOR SIZE 08 AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER, AND MATERIAL CODE LETTE
25、R. 6. INTENDED USE: THIS PART IS DESIGNED FOR USE IN TUBING CONNECTION SYSTEMS WITH MAXIMUM OPERATING PRESSURES AS FOLLOWS: a. SIZES 02 THROUGH 16 IN LOW ALLOY STEEL, CORROSION RESISTANT STEEL AND TITANIUM ALLOY AT 3000 PSI. b. SIZES 02 THROUGH 12 IN ALUMINUM ALLOY AT 3000 PSI. c. SIZE 16 IN ALUMINU
26、M ALLOY AND SIZE 20 IN ALL MATERIALS AT 1500 PSI. 7. FOR REDUCER CONFIGURATIONS, THE PRESSURE RATING IS DETERMINED BY THE LARGEST PORT. 8. THE NON-REDUCER CONFIGURATION WITHOUT A SUFFIX PART NUMBER CODE IS THE FUNCTIONAL EQUIVALENT OF AN783 AND MS24388 FOR THE CORRESPONDING FORGING SIZE AND IS INTEN
27、DED TO BE SUITABLE AS A REPLACEMENT STANDARD. 9. WHEN MACHINING FROM BAR STOCK OR OVERSIZED FORGING, THE CENTER BODY DIMENSIONS SHALL CONFORM TO AS1376, TABLE 11. /10/ DIMENSIONS “E” AND “F” ARE DETERMINED BY THE FORGING SIZE. /11/ THE DIMENSIONS IN THE TABLE ARE FOR FINAL MACHINED PARTS. THE FORGIN
28、G SIZE IS DETERMINED AS THE SIZE NECESSARY TO MAKE THE LARGEST FITTING END. /12/ THE .125 MINIMUM DIMENSION APPLIES ONLY WHEN “Z” IS SPECIFIED. WHEN “Z” IS NOT SPECIFIED, USE “V” DIMENSION. /13/ WHEN “G” DIMENSION IS NOT SPECIFIED, USE “V” DIMENSION. /14/ WEIGHTS ARE FOR NON-REDUCERS ONLY. REDUCER F
29、ITTINGS WILL HAVE LOWER WEIGHTS. AEROSPACE STANDARD AS6098SHEET 5 OF 5FITTING, TEE, STANDARD AND REDUCER, BULKHEAD ON RUN, INTERNAL PORT ON SIDE, FLARED, 37 SPHERICAL 15. INTERPRETATION OF DRAWING PER ARP4296. 16. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWI
30、SE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. FORGED SURFACES MAY BE 250 in Ra. 17. BREAK ALL SHARP EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 18. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 19. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR
31、DIMENSIONS 0 DEGREES 30. /20/ EXAMPLE OF PART NUMBER: AS6098 J 10 10 10 VTHE FINISH CODE LETTER “V” WILL BE PLACED HERE ONLY FOR MATERIAL CODE “W” PARTS THAT ARE TO BE COATED WITH HIGH PURITY ALUMINUMMATERIAL CODE LETTER /1/ SIZE CODE, TUBE SIZE OF PORT#2 IN .062 INCREMENTS SIZE CODE, TUBE SIZE OF PORT#1 IN .062 INCREMENTS BASIC PART NUMBER SIZE CODE, TUBE SIZE OF PORT #3 IN .062 INCREMENTS
