1、 AEROSPACE STANDARD CUTTING TOOL, ELECTRICAL, WIRE CUTTING WITH GRIPPING TEETH, HAND ACTUATED, TYPE I, WIRE SIZES 26 THROUGH 10 A6Copyright 2016 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any me
2、ans, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org
3、ISSUED2012-12REVISED2016-04THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 REV.A FEDERAL SUPPLY CLASS 5970 A6 SHEET 1 OF 2 REV. A PROCUREMENT SPECIFICATION: AS6173 6$(7HFKQLFDO6WDQGDUGV%RDUG5XOHVSURYLGHWKDW7KLVUHSRUWLVSXEOLVKHGE6$(WRDGYDQFHWKHVWDWHRIWHFKQLFDODQGHQJLneering sciences. The useof this rep
4、ort is entirely voluntary, and its applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,LVWKHVROHUHVSRQVLELOLWRIWKHXVHUSAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed, stabilized, or cancelled. SAE in
5、vites your written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS6173/2A RATIONALE REVISION NEEDED TO CORRECT FIGURE 1 DIMENSIONS. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED
6、 HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS6173. FIGURE 1 - BASIC WIRE CUTTER TOOL AEROSPACE STANDARD $6 SHEET 2 OF 2 REV. A CUTTING TOOL, ELECTRICAL, WIRE CUTTING WITH GRIPPING TEETH, HAND ACTUATED, TYPE I, WIRE SIZES 26 THROUGH 10 REQUIREMENTS: 1. DESIGN: OUTLINE CONFIGURATIO
7、N OPTIONAL WITHIN MAXIMUM DIMENSIONS SHOWN FOR A CLOSED HANDLE POSITION. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE .005 (0.13 MM) FOR THREE PLACE DECIMALS AND .01 (0.25 MM) FOR TWO PLACE DECIMALS. 2. MATERIALS: JAWS: 50 POINT CARBON MIN. ALLOY STEEL; HEAT TREAT ROCKWELL C4
8、3-54. CUTTER SURFACES: SHALL HAVE A MINIMUM HEAT TREAT OF ROCKWELL C53-C58. HANDLES: S 40 POINT CARBON MIN. ALLOY STEEL GRIPS: PLASTIC, RUBBER (COLOR - YELLOW). 3. FINISH: JAW - BLACK OXIDE HANDLES - BLACK OXIDE 4. TOOL ASSEMBLY WEIGHT: COMPLETE ASSEMBLY HANDLES, GRIPS, AND JAWS SHALL NOT WEIGH IN E
9、XCESS OF 1.0 POUNDS (0.45 KG). 5. PART NUMBER: M6173/2-01 DESIGNATES THE ENTIRE ASSEMBLY INCLUDING THE HANDLE, GRIPS, AND JAWS. 6. TOOL OPERATIONAL CHARACTERISTICS: A SPRING SHALL BE PROVIDED TO FULLY OPEN THE JAWS AND HANDLES WHEN THE LOCK IS NOT ENGAGED. A MAXIMUM FORCE OF 35 POUNDS SHALL BE REQUI
10、RED TO CLOSE THE CUTTER NOT INCLUDING THE FORCE TO CUT INDIVIDUAL WIRES. 7. CUTTER COMPRESSION FORCE: REQUIRED. 8. CUTTING PERFORMANCE CHARACTERISTICS: REQUIRED. 9. SHOCK CHARACTERISTICS: REQUIRED 10. HUMIDITY CHARACTERISTICS: REQUIRED 11. LIFE CHARACTERISTICS: REQUIRED (CUTTING CYCLES SHALL BE 5000
11、) 12. WORKMANSHIP: REQUIRED APPLICATION NOTES: 1. THIS WIRE CUTTER IS DESIGNED TO BE USED FOR CUTTING AIRCRAFT WIRING SUCH AS AS22759 WITH TIN, NICKEL, AND SILVER COATED CONDUCTORS OF COPPER, AND HIGH STRENGTH OR ULTRA HIGH STRENGTH COPPER ALLOY. SPECIFICATION NOTES: 1. REVISION INDICATOR: A CHANGE
12、BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS IS AN SAE INTERNATIONAL PUBLICATION.
