1、AEROSPACE STANDARD O-RING, MOLDED FROM AMS7379 RUBBER FOR USE WITH AS5202 PORTS AS6203Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, r
2、ecording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2013-04THIRD ANGLE PROJECTION CUSTODI
3、AN: A-6/A-6C FEDERAL SUPPLY CLASS 5331 AS6203SHEET 1 OF 3PROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitab
4、ility forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE value
5、s your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS6203RATIONALETHIS STANDARD ESTABLISHES THE DIMENSIONAL AND VISUAL QUALITY REQUIREMENTS, LOT REQUIREMENTS AND PACKAGING AND LABELING REQUIREMENTS FOR BOSS O-RINGS MOLDED FROM AMS7379 RUBBER
6、 FOR USE WITH AS5202 PORTS. IT SHALL BE USED FOR PROCUREMENT PURPOSES. AASECTION W DA-A2X .005 MAX2X .003 MAXNOTE: DIMENSION AND TOLERANCING PER ASME Y14.5 FIGURE 1 - BOSS O-RING DIMENSIONS FOR TABLE 1 WIDTH (W) AND INSIDE DIAMETER (D) TABLE 1 - TUBE SIZES AND O-RING GASKETS FOR AS5202 PORTS PARTNUM
7、BER TUBEOUTSIDEDIAMETERD W APPROX. MASSINCH MM (INCH) (MM) INCH MM LB/100 KG/100 AS6203-901 .094 2.388 .190/.180 4.826/4.572 .059/.053 1.499/1.346 .008 0.003 AS6203-902 .125 3.175 .244/.234 6.198/5.944 .067/.061 1.702/1.549 .010 0.005 AS6203-903 .188 4.775 .306/.296 7.772/7.518 .067/.061 1.702/1.549
8、 .012 0.005 AS6203-904 .250 6.350 .356/.346 9.042/8.788 .075/.069 1.905/1.753 .015 0.007 AS6203-905 .312 7.925 .419/.409 10.643/10.389 .075/.069 1.905/1.753 .017 0.008 .AS6203-906 .375 9.525 .473/.463 12.014/11.760 .081/.075 2.057/1.905 .020 0.009 AS6203-907 .438 11.125 .537/.523 13.640/13.284 .085/
9、.079 2.159/2.007 .023 0.010 AS6203-908 .500 12.700 .653/.635 16.586/16.129 .090/.084 2.286/2.134 .027 0.012 AS6203-909 .562 14.275 .715/.697 18.161/17.704 .100/.094 2.540/2.388 .033 0.015 AS6203-910 .625 15.875 .764/.746 19.406/18.948 .100/.094 2.540/2.388 .034 0.016 AS6203-911 .688 17.475 .872/.854
10、 22.149/21.692 .120/.112 3.048/2.845 .048 0.022 AS6203-912 .750 19.050 .933/.915 23.698/23.241 .120/.112 3.048/2.845 .050 0.023 AS6203-913 .812 20.625 .996/.976 25.298/24.790 .120/.112 3.048/2.845 .051 0.023 AS6203-914 .875 22.225 1.057/1.037 26.848/26.340 .120/.112 3.048/2.845 .053 0.024 AS6203-916
11、 1.000 25.400 1.181/1.161 29.997/29.489 .120/.112 3.048/2.845 .056 0.025 AS6203-918 1.125 28.575 1.367/1.343 34.722/34.112 .120/.112 3.048/2.845 .061 0.028 AS6203-920 1.250 31.750 1.489/1.461 37.821/37.109 .122/.114 3.099/2.896 .065 0.030 AS6203-924 1.500 38.100 1.734/1.706 44.044/43.332 .122/.114 3
12、.099/2.896 .071 0.032 AS6203-928 1.750 44.450 2.108/2.072 53.543/52.629 .122/.114 3.099/2.896 .081 0.037 AS6203-932 2.000 50.800 2.355/2.319 59.817/58.903 .122/.114 3.099/2.896 .087 0.040 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking pe
13、rmitted without license from IHS-,-,-AEROSPACE STANDARD AS6203SHEET 2 OF 3O-RING, MOLDED FROM AMS7379 RUBBER FOR USE WITH AS5202 PORTS APPLICATION: 1. THESE O-RINGS, USED AS SEALS FOR AS5202 PORTS IN AEROSPACE APPLICATIONS, HAVE RESISTANCE TO A VARIETY OF GAS TURBINE ENGINE OILS, INCLUDING HIGH THER
14、MAL STABILITY (HTS) OILS, FUELS, AND HYDRAULIC FLUIDS, BUT USAGE IS NOT LIMITED TO SUCH APPLICATIONS. EACH APPLICATION SHOULD BE CONSIDERED SEPARATELY. THESE O-RINGS HAVE A TYPICAL SERVICE TEMPERATURE RANGE OF -60 TO +400 F (-51 TO +204 C) IN AIR. APPLICABLE REFERENCES: 1. SAE PUBLICATIONS AVAILABLE
15、 FROM SAE INTERNATIONAL, 400 COMMONWEALTH DRIVE, WARRENDALE, PA 15096-0001, TEL: 877-606-7323 (INSIDE USA AND CANADA) OR 724-776-4970 (OUTSIDE USA), www.sae.org.AMS2817 PACKAGING AND IDENTIFICATION, PREFORMED PACKINGS AMS7379 RUBBER: FLUOROCARBON ELASTOMER (FKM) 70 TO 80 HARDNESS, LOW TEMPERATURE SE
16、ALING Tg -40 F (-40 C) FOR ELASTOMERIC SEALS IN AIRCRAFT ENGINE OIL, FUEL AND HYDRAULIC SYSTEMS ARP5316 STORAGE OF ELASTOMER SEALS AND SEAL ASSEMBLIES WHICH INCLUDE AN ELASTOMER ELEMENT PRIOR TO HARDWARE ASSEMBLY 2. ASQ PUBLICATIONS AVAILABLE FROM AMERICAN SOCIETY OF QUALITY, 600 NORTH PLANKINTON AV
17、ENUE, MILWAUKEE, WI 53203, TEL: NORTH AMERICA: 800-248-1946 (UNITED STATES AND CANADA ONLY), MEXICO: 001-800-514-1564, ALL OTHER LOCATIONS: +1-414-272-8575, www.asq.org.ANSI/ASQ Z1.4 SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES 3. ASME AND ISO PUBLICATIONS AVAILABLE FROM AMERICAN NATI
18、ONAL STANDARDS INSTITUTE, 25 WEST 43RD STREET, NEW YORK, NY 10036-8002, TEL: 212-642-4900, www.ansi.org.Y 14.5 DIMENSIONING AND TOLERANCING ISO 3601-1 FLUID POWER SYSTEMS - O-RINGS - PART 1: INSIDE DIAMETERS, CROSS-SECTIONS, TOLERANCES AND DESIGNATION CODES ISO 3601-3 FLUID POWER SYSTEMS - O-RINGS -
19、 PART 3: QUALITY ACCEPTANCE CRITERIA REQUIREMENTS: 1. MATERIAL: THE MATERIAL SHALL BE IN ACCORDANCE WITH AMS7379. 2. DIMENSIONAL AND VISUAL INSPECTION: PRIOR TO INSPECTION, MOLD FLASH SHALL BE REMOVED FROM THE O-RINGS IN SUCH A MANNER THAT THEY CONFORM TO THE REQUIREMENTS SPECIFIED HEREIN. FOR END O
20、F PROCESS INSPECTION, EACH INDIVIDUAL O-RING (100%) SHALL BE MANUALLY INSPECTED ACCORDING TO ISO 3601-3, GRADE CS REQUIREMENTS UNDER 1X MAGNIFICATION. THE ENTIRE O-RING SURFACE SHALL BE INSPECTED. 3. FOR FINAL INSPECTION, THE SAMPLE SIZE SHALL BE IN ACCORDANCE WITH ANSI/ASQ Z1.4 SINGLE SAMPLING PLAN
21、 INSPECTION LEVEL II WITH AN AQL 1.0 EXCEPT THAT THE ACCEPTANCE NUMBER SHALL BE ZERO. THE SAMPLE UNIT SHALL BE ONE O-RING. INSPECTION SHALL BE ACCORDING TO ISO 3601-3, GRADE CS REQUIREMENTS UNDER 2X MAGNIFICATION. THE ENTIRE O-RING SURFACE SHALL BE MANUALLY INSPECTED. THE PROCEDURES OUTLINED IN ANNE
22、X B OF ISO 3601-1 SHALL BE FOLLOWED FOR DIMENSIONAL INSPECTION. IF THE PURCHASER REQUIRES A DIFFERENT SAMPLING PLAN OR VISUAL INSPECTION CRITERIA, MANUFACTURER SHALL BE INFORMED PRIOR TO TIME OF ORDER. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or
23、 networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS6203SHEET 3 OF 3O-RING, MOLDED FROM AMS7379 RUBBER FOR USE WITH AS5202 PORTS 4. THE MANUFACTURER OF THE O-RINGS SHALL BE RESPONSIBLE FOR THE REQUIRED INSPECTIONS. PURCHASER RESERVES THE RIGHT TO SAMPLE AND PERFORM ANY CONFIRMATO
24、RY INSPECTION DEEMED NECESSARY TO ENSURE THAT THE O-RINGS CONFORM TO THE SPECIFIED REQUIREMENTS. 5 LOT ACCEPTANCE: THE REQUIREMENTS ARE LISTED IN AMS7379. THE LOT CERTIFICATION REPORT SHALL BE FURNISHED TO THE PURCHASER WHEN THE PRODUCT IS SHIPPED. THE MANUFACTURER OF THE O-RINGS SHALL BE RESPONSIBL
25、E FOR THE LOT ACCEPTANCE TESTS. PURCHASER RESERVES THE RIGHT TO SAMPLE AND PERFORM ANY CONFIRMATORY INSPECTION DEEMED NECESSARY TO ENSURE THAT THE O-RINGS CONFORM TO THE SPECIFIED REQUIREMENTS 6. IDENTIFICATION AND PACKAGING: AMS2817 WITH THE FOLLOWING EXCEPTIONS: IF REQUIRED BY PURCHASER: NATIONAL
26、STOCK NUMBER IF REQUIRED BY PURCHASER: SHELF LIFE REQUIREMENTS OF ARP5316 IF REQUIRED BY PURCHASER: NUMBER OF O-RINGS PER PACKAGE7. PURCHASE DOCUMENTS SHOULD SPECIFY NOT LESS THAN THE FOLLOWING: PART NUMBER OF O-RING PER AS6203 QUANTITY OF O-RINGS DESIRED SPECIAL PACKAGING AND LABELING, IF REQUIRED
27、8. DO NOT USE UNASSIGNED PART NUMBERS. SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DO
28、CUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
