1、AEROSPACE STANDARD ACCESSORY, CAP, PROTECTIVE LOCKING, CONNECTOR, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING AS81511/16Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in
2、 any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRE
3、SS: http:/www.sae.org ISSUED 2014-10THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 FEDERAL SUPPLY CLASS 5935 AS81511/16SHEET 1 OF 2PROCUREMENT SPECIFICATION: AS81511SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences.
4、 Theuse ofthisreportis entirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, is thesole responsibilityoftheuser.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized
5、 orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81511/16RATIONALE THIS DETAIL SPECIFICATION SHEET IS WRITTEN TO PERMIT THE CANCELLATION AND SUPERSESSION OF MIL-C-81
6、511/16 WITH THIS DOCUMENT. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. FIGURE 1 - PROTECTIVE CAP, LOCKING AEROSPACE STANDARD AS81511/16SHEET 2 OF 2ACCESSORY, CAP, PROTECTIVE LOCKING, CONNECTOR, ELECTRICAL
7、 CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING TABLE 1 - FIGURE 1 METRIC EQUIVALENTS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS .005 0.13 .250 6.35 .426 10.82 .010 0.25 .381 9.68 .441 11.20 .185 4.70 .396 10.06 TABLE 2 - FIGURE 1 DIMENSIONS/CONFIGURATION PARTNUMBER S
8、HELLSIZESDIA.TDIA.UDIA.FTHREADAPPROX. WEIGHT (LB) M81511/16-08 8 .552(14.02) .532(13.51) .451(11.46) .443(11.25) .300(7.62).290(7.37) 1/2-28UNEF-2B .0010 M81511/16-10 10 .679(17.25) .659(16.74) .576(14.63) .568(14.43) .425(10.80) .415(10.54) 5/8-28UN-2B .0016 M81511/16-14 14 .925(23.50) .905(22.99)
9、826(20.98) .818(20.78) .675(17.15) .665(16.89) 7/8-28UN-2B .0023 M81511/16-16 16 1.053(26.75) 1.033(26.24) .951(24.16) .943(23.95) .799(20.29) .789(20.04) 1-28UN-2B .0029 M81511/16-18 18 1.179(29.95) 1.159(29.44) 1.075(27.31) 1.067(27.10) .935(23.75) .925(23.50) 1 1/8-28UN-2B .0033 REQUIREMENTS: AL
10、L REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. 1. DESIGN: PROTECTIVE CAPS SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE 2. DIMENSIONS ARE IN INCHES AND APPLY AFTER PLATING. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 1 INCH = 2
11、5.4 MM. UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE .016 INCHES. CAP IS USED WITH CLASS E CONNECTORS WHEN THE REAR ACCESSORY HARDWARE IS NOT EMPLOYED. 2. MATERIAL: MATERIAL SHALL BE 103 NYLON PLASTIC (BLACK). APPLICATION NOTES: 1. AS81511 CONNECTORS AND ACCESSORIES ARE NOT RECOMMENDED FOR NEW DESIGN.
12、 SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
