1、AEROSPACE STANDARD CONNECTOR, RECEPTACLE, FLANGE MOUNT, ELECTRICAL,CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, CRIMP TYPE CONTACTS, CLASS A, F, AND E (SERIES 1)AS81511/21Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored i
2、n a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Emai
3、l: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2014-10THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 FEDERAL SUPPLY CLASS 5935 AS81511/21SHEET 1 OF 3PROCUREMENT SPECIFICATION: AS81511SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thesta
4、te of technicalandengineering sciences. Theuse ofthisreportis entirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, is thesole responsibilityoftheuser.”SAE reviews eachtechnicalreport at least every five years at which time
5、 itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81511/21RATIONALE THIS DETAIL SPECIFICATION SHEET IS WRITTEN TO PERMIT THE CA
6、NCELLATION AND SUPERSESSION OF MIL-C-81511/21 WITH THIS DOCUMENT. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. FIGURE 1 - CONNECTOR RECEPTACLE, FLANGE MOUNT AEROSPACE STANDARD AS81511/21SHEET 2 OF 3CONNECT
7、OR, RECEPTACLE, FLANGE MOUNT, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, CRIMP TYPE CONTACTS, CLASS A, F, AND E (SERIES 1)TABLE 1 - FIGURE 1 METRIC EQUIVALENTS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS .003 0.08 .067 1.70 .126 3.20
8、1.406 35.71 .005 0.13 .073 1.85 .143 3.63 1.436 36.47.006 0.15 .075 1.91 .153 3.89 1.471 37.36 .010 0.25 .090 2.29 .200 5.08 1.531 38.89.015 0.38 .094 2.39 .230 5.84 .016 0.41 .116 2.95 .894 22.71 .065 1.65 .125 3.18 .906 23.01 TABLE 2 - FIGURE 1 DIMENSIONS/CONFIGURATION SHELLSIZEBDEFTHREAD G H PARB
9、SCBRBSCCR BSCDR BSCFF RAD. EE BSC POSITION 1234568.553(14.05).547(13.89) .430(10.92).424(10.77) .422(10.72).407(10.34)1/2-28UNEF-2A.820(20.83) .804(20.42).599(15.21) .589(14.96).640(16.26).630(16.00)105 140 215 265 .120(3.05).100(2.54) 60 46 43 60 89 4310.678(17.22).672(17.07) .555(14.10).549(13.94)
10、 .548(13.92).533(13.54)5/8-28UN-2A .945(24.00) .929(23.60).724(18.39) .714(18.14).765(19.43).755(19.18)95 141 208 236 .120(3.05).100(2.54) 53 87 51 77 87 8714.928(23.57).922(23.42) .805(20.45).799(20.29) .798(20.27).783(19.89)7/8-28UN-2A 1.133(31.95) 1.117(28.37).911(23.14) .901(22.89)1.015(25.78)1.
11、005(25.53)95 141 208 236 .120(3.05).100(2.54) 53 87 51 77 87 87161.054(26.77)1.048(26.62) .930(23.63).924(23.47) .924(23.47).909(23.09)1-28UN-2A 1.258(31.95) 1.242(31.55).974(24.74) .964(24.49)1.140(28.96)1.130(28.70)80 142 196 293 .150(3.81).130(3.30) 98 98 98 98 98 98181.178(29.92)1.172(29.77) 1.0
12、55(26.80)1.049(26.64) 1.048(26.62)1.033(26.24)1 1/8-28UN-2A 1.351 (34.32) (1.335(33.91)1.067(27.10) 1.057(26.85)1.265(32.13)1.255(31.88)80 142 196 293 .150(3.81).130(3.30) 98 98 98 98 98 98201.303(36.27)1.297(32.94) 1.180(29.97)1.174(29.82) 1.173(29.79)1.158(29.41)1 1/8-28UN-2A 1.475(37.47) 1.459(37
13、06)1.161(29.49) 1.151(29.24)1.390(35.31)1.380(35.05)80 142 196 293 98 98 98 98 98 98221.428(36.27)1.422(36.12) 1.305(33.15)1.299(32.99) 1.298(32.97)1.283(32.59)1 3/8-28UN-2A 1.570(39.88) 1.554(39.47)1.255(31.88) 1.245(31.62)1.515(38.48)1.505(38.23)80 142 196 293 98 98 98 98 98 98241.553(39.45)1.547
14、39.29) 1.430(36.32)1.424(36.17) 1.423(36.14)1.408(35.76)1 1/2-28UN-2A 1.711(43.46) 1.695(43.05)1.380(35.05) 1.370(34.80)1.640(41.66)1.630(41.40)80 142 196 293 98 98 98 98 98 98REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. 1. DESIGN: CONNECTORS SHALL
15、BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE 1. DIMENSIONS ARE IN INCHES AND APPLY AFTER PLATING. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MM. UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE .016 INCHES. NORMAL MATING KEYWAY POSITION SHOWN. FOR ALTERNA
16、TE KEYWAY POSITIONS, SEE AS81511, FIGURE 8. 2. FOR INSERT ARRANGEMENTS, SEE AS81511, APPENDIX A. AEROSPACE STANDARD AS81511/21SHEET 3 OF 3CONNECTOR, RECEPTACLE, FLANGE MOUNT, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, CRIMP TYPE CONTACTS, CLASS A, F, AND E (SERIES 1
17、)3. PART NUMBER: THE CONNECTOR PART NUMBER WILL CONSIST OF THE LETTER M, THE BASIC SPECIFICATION NUMBER/APPLICABLE SPECIFICATION SHEET, AND THE APPLICABLE ALPHA-NUMERIC CHARACTERS ON THE CONNECTOR SHELL. THE PART NUMBER SHALL BE FORMULATED AS IN THE FOLLOWING EXAMPLE: M81511/21ED01P1. 4. SHELL POLAR
18、IZATION: 1 THROUGH 6 KEY POSITION. 5. INSERTION AND REMOVAL TOOLS: AS81969/2 INSERTION TOOL, AS81969/3 REMOVAL TOOL. 6. MATING CONNECTOR: THIS RECEPTACLE MATES DIRECTLY WITH AN AS81511/26 PLUG. 7. CONNECTOR WEIGHT: THE CONNECTOR REFERENCE WEIGHTS ARE LISTED IN TABLE 3. TABLE 3 - CONNECTOR WEIGHTSHEL
19、L SIZE WEIGHT (REFERENCE - POUNDS) 1/ 24 (CODE J) .122 22 (CODE H) .109 20 (CODE G) .095 18 (CODE F) .080 16 (CODE E) .067 14 (CODE D) .056 10 (CODE B) .035 8 (CODE A) .027 1/ REMOVABLE CRIMP CONTACTS NOT INCLUDED IN WEIGHT APPLICATION NOTES: 1. AS81511 CONNECTORS AND ACCESSORIES ARE NOT RECOMMENDED
20、 FOR NEW DESIGN. SPECIFICATION NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE
21、TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
