1、AEROSPACE STANDARD CONNECTOR, RECEPTACLE, JAM NUT MOUNT, ELECTRICAL,CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, CRIMP TYPE CONTACTS; ANDACCESSORIES (CLASS A, F, AND E - SERIES 2)AS81511/3Copyright 2014 SAE International All rights reserved. No part of this publication may be rep
2、roduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax:
3、724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2014-10THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 FEDERAL SUPPLY CLASS 5935AS81511/3SHEET 1 OF 4PROCUREMENT SPECIFICATION: AS81511SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE t
4、oadvance thestate of technicalandengineering sciences. Theuse ofthisreportis entirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, is thesole responsibilityoftheuser.”SAE reviews eachtechnicalreport at least every five year
5、s at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81511/3RATIONALE THIS DETAIL SPECIFICATION SHEET IS WRITTEN TO
6、 PERMIT THE CANCELLATION AND SUPERSESSION OF MIL-C-81511/3 WITH THIS DOCUMENT. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. FIGURE 1 - CONNECTOR RECEPTACLE, JAM NUT MOUNT AEROSPACE STANDARD AS81511/3SHEET
7、2 OF 4CONNECTOR, RECEPTACLE, JAM NUT MOUNT, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, CRIMP TYPE CONTACTS; AND ACCESSORIES (CLASS A, F, AND E - SERIES 2)FIGURE 1A - CONNECTOR RECEPTACLE TABLE 1 - FIGURE 1 METRIC EQUIVALENTS INCHES MILLIMETERS INCHES MILLIMETERS INC
8、HES MILLIMETERS INCHES MILLIMETERS .003 0.08 .067 1.70 .200 5.08 .778 19.76 .005 0.13 .073 1.85 .230 5.84 1.275 32.39.006 0.15 .090 2.29 .482 12.24 1.340 34.04 .015 0.38 .094 2.39 .502 12.75 1.400 35.56.020 0.51 .125 3.18 .770 19.56 TABLE 2 FIGURE 1 DIMENSIONS SHELLSIZEBDEFTHREADGACROSS FLATS KLACRO
9、SS FLAT LL NTHREADP8 .553(14.05) .547(13.89) .430(10.92).424(10.77) .422(10.72).407(10.34) 1/2-28UNEF-2A.989(25.12) .969(24.61) 1.072(27.23) 1.052(26.72).598(15.19) .590(14.99) .610(15.49) .600(15.24) 5/8-20UN-2A .640(16.26).630(16.00)10.678(17.22) .672(17.07) .555(14.10).549(13.94) .548(13.92).533(
10、13.54) 5/8-28UN-2A 1.114(28.30) 1.094(27.79) 1.197(30.40) 1.177(29.90).723(18.36) .715(18.16) .735(18.67) .725(18.42) 3/4-20UNEF-2A.765(19.43) .755(19.18)14.928(23.57) .922(23.42) .805(20.45).799(20.29) .798(20.27).783(19.89) 7/8-28UN-2A 1.401(35.59) 1.381(35.08) 1.510(38.35) 1.490(37.85).973(24.71)
11、 .965(24.51) .985(25.02) .975(24.77) 1-20UNEF-2A1.015(25.78) 1.005(25.53)161.054(26.77) 1.048(26.62) .930(23.63).924(23.47) .924(23.47).909(23.09) 1-28UN-2A 1.526(38.76) 1.506(38.25) 1.635(41.53) 1.615(41.02)1.098(27.89) 1.090(27.69) 1.110(28.19) 1.100(27.94) 1 1/8-20UN-2A1.140(28.96)1.130(28.70)181
12、178(29.92) 1.172(29.77) 1.055(26.80)1.049(26.64) 1.048(26.62)1.033(26.24) 1 1/8-28UN-2A 1.651(41.94) 1.631(41.43) 1.745(44.32) 1.725(43.82)1.222(31.04) 1.214(30.84) 1.235(31.37) 1.225(31.12) 1 1/4-20UN-2A1.265(32.13) 1.255(31.88)AEROSPACE STANDARD AS81511/3SHEET 3 OF 4CONNECTOR, RECEPTACLE, JAM NUT
13、 MOUNT, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, CRIMP TYPE CONTACTS; AND ACCESSORIES (CLASS A, F, AND E - SERIES 2)TABLE 2A - FIGURE 1 DIMENSIONS (CONTINUED) SHELLSIZEARBSCBRBSCCR BSCDR BSCPANELO-RING EE BSC POSITION 1 2 3 4 5 6 8 128 - - - AS3582-018 40 40 40 40
14、 40 40 10 105 140 215 265 AS3582-020 60 46 46 60 89 60 14 105 140 215 265 AS3582-024 60 46 46 60 89 60 16 105 140 215 265 AS3582-026 50 50 50 50 50 50 18 105 140 215 265 AS3582-028 50 50 50 50 50 50 REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DCOUMENT AND THE LATEST ISSUE OF AS81511. 1. DES
15、IGN: CONNECTORS SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE 2. DIMENSIONS ARE IN INCHES AND ARE AFTER PLATING. METRIC EQUIVALENTS ARE GIVEN FOR INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MM. UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE .016 INCHES. THE NORMAL MATING KEYWAY POSITION IS
16、 SHOWN IN FIGURES 1 AND 1A. FOR ALTERNATE KEYWAY POSITIONS, SEE AS81511 FIGURE 4. THE .200 MAX. DIMENSION IN FIGURE 1A IS THE DISTANCE FROM THE FRONT OF THE SHELL TO THE POINT AT WHICH A GAGE PIN, HAVING THE SAME BASIC DIAMETER AS THE PLUG SHELL, ENGAGES THE SPRING MEMBER. CONNECTORS ARE SERIES 2, C
17、LASSES ARE A, F, AND E. CONTACTS ARE CRIMP TYPE REMOVABLE, STYLE P AND S. 2. FOR INSERT ARRANGEMENTS, SEE AS81511, APPENDIX A. 3. PART NUMBER: THE CONNECTOR PART NUMBER WILL CONSIST OF THE LETTER M, THE BASIC SPECIFICATION NUMBER/APPLICABLE SPECIFICATION SHEET, AND THE APPLICABLE ALPHA-NUMERIC CHARA
18、CTERS ON THE CONNECTOR SHELL. THE PART NUMBER SHALL BE FORMULATED AS IN THE FOLLOWING EXAMPLE: M81511/03ED01P1.M81511/03 E D 01 P 1 BASIC PART NUMBERCLASSSHELL SIZE INSERT ARRANGEMENT CONTACT DESIGNATOR KEY POSITIONS 4. SHELL POLARIZATION: 1 THROUGH 6 KEY POSITION. 5. INSERTION AND REMOVAL TOOLS: AS
19、81969/2 INSERTION TOOL, AS81969/3 REMOVAL TOOL. 6. MATING CONNECTOR: THIS RECEPTACLE MATES DIRECTLY WITH AN AS81511/6 PLUG. 7. CONNECTOR WEIGHT: THE CONNECTOR REFERENCE WEIGHTS ARE LISTED IN TABLE 3. 8. SLOTTED NUT: THE SLOTTED NUT SHALL CONFORM TO AS81511/20. AEROSPACE STANDARD AS81511/3SHEET 4 OF
20、4CONNECTOR, RECEPTACLE, JAM NUT MOUNT, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, CRIMP TYPE CONTACTS; AND ACCESSORIES (CLASS A, F, AND E - SERIES 2)TABLE 3 - CONNECTOR WEIGHT SHELL SIZE WEIGHT (REFERENCE - POUNDS) 1/ 18 (CODE F) .090 16 (CODE E) .078 14 (CODE D) .0
21、63 10 (CODE B) .040 8 (CODE A) .030 1/ CONTACTS NOT INCLUDED IN WEIGHT. APPLICATION NOTES: 1. AS81511 CONNECTORS AND ACCESSORIES ARE NOT RECOMMENDED FOR NEW DESIGN. 2. FOR SHELL SIZES 20, 22, AND 24, USE AS81511/23 CONNECTORS. SPECIFICATION NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAIN
22、S CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
