1、AEROSPACE STANDARD CONNECTOR, RECEPTACLE, FLANGE MOUNT, ELECTRICAL,CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, INDIVIDUAL RELEASE, CRIMPTYPE CONTACTS (CLASS A, F, AND E - SERIES 3)AS81511/41Copyright 2014 SAE International All rights reserved. No part of this publication may be
2、reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fa
3、x: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2014-10THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 FEDERAL SUPPLY CLASS 5935AS81511/41SHEET 1 OF 3PROCUREMENT SPECIFICATION: AS81511SAE Technical Standards Board Rules provide that: “This report ispublishedby S
4、AE toadvance thestate of technicalandengineering sciences. Theuse ofthisreportis entirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, is thesole responsibilityoftheuser.”SAE reviews eachtechnicalreport at least every five
5、years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81511/41RATIONALE THIS DETAIL SPECIFICATION SHEET IS WRITT
6、EN TO PERMIT THE CANCELLATION AND SUPERSESSION OF MIL-C-81511/41 WITH THIS DOCUMENT. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF SAE AS81511. FIGURE 1 - CONNECTOR RECEPTACLE AEROSPACE STANDARD AS81511/4
7、1SHEET 2 OF 3CONNECTOR, RECEPTACLE, FLANGE MOUNT, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, INDIVIDUAL RELEASE, CRIMP TYPE CONTACTS (CLASS A, F, AND E - SERIES 3)TABLE 1 - FIGURE 1 METRIC EQUIVALENTS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS INCHES M
8、ILLIMETERS .003 0.08 .065 1.65 .126 3.20 1.298 32.97 .005 0.13 .067 1.70 .143 3.63 1.318 33.48.006 0.15 .073 1.85 .153 3.89 1.327 33.71 .010 0.25 .090 2.29 .200 5.08 1.347 34.21.015 0.38 .094 2.39 .230 5.84 .016 0.41 .116 2.95 .894 22.71 .035 0.89 .125 3.18 .906 23.01 TABLE 2 - FIGURE 1 DIMENSIONS/C
9、ONFIGURATION SHELLSIZEBDFTHREAD G H PARBSCBRBSCCR BSCDR BSCFF RAD. EE BSC POSITION 1 234568.553(14.05).547(13.89) .430(10.92).424(10.77) 1/2-28UNEF-2A .820(20.83) .804(20.42).599(15.21) .589(14.96).640(16.26).630(16.00)105 140 215 265 .120(3.05).100(2.54) 60 46 43 60 89 4310.678(17.22).672(17.07) .5
10、55(14.10).549(13.94) 5/8-28UN-2A .945(24.00) .929(23.60).724(18.39) .714(18.14).765(19.43).755(19.18)95 141 208 236 .120(3.05).100(2.54) 53 87 51 77 87 8714.928(23.57).922(23.42) .805(20.45).799(20.29) 7/8-28UN-2A 1.133(28.78) 1.117(28.37).911(23.14) .901(22.89)1.015(25.78)1.005(25.53)95 141 208 236
11、 .120(3.05).100(2.54) 53 87 51 77 87 87161.054(26.77)1.048(26.62) .930(23.63).924(23.47) 1-28UN-2A 1.258(31.95) 1.242(31.55).974(24.74) .964(24.49)1.140(28.96)1.130(28.70)80 142 196 293 .150(3.81).130(3.30) 98 98 98 98 98 98181.178(29.92)1.172(29.77) 1.055(26.80)1.049(26.64) 1 1/8-28UN-2A 1.351(34.3
12、2) 1.335(33.91)1.067(27.10) 1.057(26.85)1.265(32.13)1.255(31.88)80 142 196 293 .150(3.81).130(3.30) 98 98 98 98 98 98201.303(33.10)1.297(32.94) 1.180(29.97)1.174(29.82) 1 1/4-28UN-2A 1.475(37.47) 1.459(37.06)1.161(29.49) 1.151(29.24)1.390(35.31)1.380(35.05)80 142 196 293 .160(4.07).130(3.30) 98 98 9
13、8 98 98 98221.428(36.27)1.422(36.12) 1.305(33.15)1.299(32.99) 1 3/8-28UN-2A 1.570(39.88) 1.554(39.47)1.255(31.88) 1.245(31.62)1.515(38.48)1.505(38.23)80 142 196 293 .160(4.07).130(3.30) 98 98 98 98 98 98241.553(39.45)1.547(39.29) 1.430(36.32)1.424(36.17) 1 1/2-28UN-2A 1.711(43.46) 1.695(43.05)1.380(
14、35.05) 1.370(34.80)1.640(41.66)1.630(41.40)80 142 196 293 .160(4.07).130(3.30) 98 98 98 98 98 98REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. 1. DESIGN: CONNECTORS SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE 2. DIMENSIONS ARE IN INCHES AND
15、 APPLY AFTER PLATING. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MM. UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE .016 INCHES. NORMAL MATING KEYWAY POSITION SHOWN IN FIGURE 1. FOR ALTERNATE KEYWAY POSITIONS, SEE AS81511, FIGURE 8. 2. FOR INSERT ARRANGEMENT
16、S, SEE AS81511, APPENDIX A. AEROSPACE STANDARD AS81511/41SHEET 3 OF 3CONNECTOR, RECEPTACLE, FLANGE MOUNT, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, INDIVIDUAL RELEASE, CRIMP TYPE CONTACTS (CLASS A, F, AND E - SERIES 3)3. PART NUMBER: THE CONNECTOR PART NUMBER WILL
17、CONSIST OF THE LETTER M, THE BASIC SPECIFICATION NUMBER/APPLICABLE SPECIFICATION SHEET, AND THE APPLICABLE ALPHA-NUMERIC CHARACTERS ON THE CONNECTOR SHELL. THE PART NUMBER SHALL BE FORMULATED AS IN THE FOLLOWING EXAMPLE: M81511/41ED01P1. M81511/41 E D 01 P 1 BASIC PART NUMBERCLASSSHELL SIZE INSERT A
18、RRANGEMENT CONTACT DESIGNATOR KEY POSITIONS 4. SHELL POLARIZATION: 1 THROUGH 6 KEY POSITION. 5. INSERTION AND REMOVAL TOOLS: AS81969/16 INSERTION/REMOVAL TOOL. 6. MATING CONNECTOR: THIS RECEPTACLE MATES DIRECTLY WITH AS81511/26 AND /46 PLUGS. APPLICATION NOTES: 1. AS81511 CONNECTORS AND ACCESSORIES
19、ARE NOT RECOMMENDED FOR NEW DESIGN. SPECIFICATION NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LO
20、CATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
