1、 AEROSPACE STANDARD CONNECTOR, RECEPTACLE, JAM NUT MOUNT, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, INDIVIDUAL RELEASE, CRIMP TYPE CONTACTS (CLASS A, F, AND W - SERIES 3) AS81511/49Copyright 2015 SAE International All rights reserved. No part of this publication ma
2、y be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside US
3、A) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2014-10REVISED 2015-04THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.A FEDERAL SUPPLY CLASS 5935AS81511/49 SHEET 1 OF 4 REV. A PROCUREMENT SPECIFICATION: AS81511SAE Technical Standards Board Rules provide
4、 that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews each
5、technicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81511/49A RATIONALE LI
6、MITED SCOPE REVISION IS REQUIRED TO CORRECT FIGURE 1, THE LABELS FOR DIMENSION G AND K WERE OMITTED DURING THE AS CONVERSION, THE FIGURE 1 DRAWING NEEDS TO BE CORRECTED TO ADD THE DIMENSION G AND K LABELS. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF T
7、HIS DOCUMENT AND THE LATEST ISSUE OF AS81511. FIGURE 1 - CONNECTOR RECEPTACLE, JAM NUT MOUNT (SERIES 3) AEROSPACE STANDARD AS81511/49 SHEET 2 OF 4 REV. A CONNECTOR, RECEPTACLE, JAM NUT MOUNT, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, INDIVIDUAL RELEASE, CRIMP TYPE
8、CONTACTS (CLASS A, F, AND W - SERIES 3) FIGURE 1 - CONNECTOR RECEPTACLE, JAM NUT MOUNT (SERIES 3) (CONTINUED) TABLE 1 - FIGURE 1 METRIC EQUIVALENTS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS .003 0.08 .067 1.70 .125 3.18 .906 23.01 .005 0.13 .073 1.85 .230 5.84 1.298
9、 32.97.006 0.15 .090 2.29 .578 14.68 1.318 33.48 .015 0.38 .094 2.39 .602 15.29 1.327 33.71.020 0.51 .100 2.54 .894 22.71 1.347 34.21 AEROSPACE STANDARD AS81511/49 SHEET 3 OF 4 REV. A CONNECTOR, RECEPTACLE, JAM NUT MOUNT, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, I
10、NDIVIDUAL RELEASE, CRIMP TYPE CONTACTS (CLASS A, F, AND W - SERIES 3) TABLE 2 - FIGURE 1 DIMENSIONS/CONFIGURATION SHELL SIZE B D F THREAD G ACROSS FLATS K L ACROSS FLAT N THREAD P LL 8 .553 (14.05) .547 (13.89) .430 (10.92) .424 (10.77) 1/2-28UNEF-2A.989 (25.12) .969 (24.61) 1.072 (27.23) 1.052 (26.
11、72) .598 (15.19) .590 (14.99) 5/8-20UN-2A .640 (16.26) .630 (16.00) .610 (15.49) .600 (15.24)10 .678 (17.22) .672 (17.07) .555 (14.10) .549 (13.94) 5/8-28UN-2A 1.114 (28.30) 1.094 (27.79) 1.197 (30.40) 1.177 (29.90) .723 (18.36) .715 (18.16) 3/4-20UNEF-2A .765 (19.43) .755 (19.18) .735 (18.67) .725
12、(18.42)14 .928 (23.57) .922 (23.42) .805 (20.45) .799 (20.29) 7/8-28UN-2A 1.401 (35.59) 1.381 (35.08) 1.510 (38.35) 1.490 (37.85) .973 (24.71) .965 (24.51) 1-20UNEF-2A 1.015 (25.78) 1.005 (25.53) .985 (25.02) .975 (24.77)16 1.054 (26.77) 1.048 (26.62) .930 (23.63) .924 (23.47) 1-28UN-2A 1.526 (38.76
13、) 1.506 (38.25) 1.635 (41.53) 1.615 (41.02) 1.098 (27.89) 1.090 (27.69) 1 1/8-20UN-2A 1.140 (28.96) 1.130 (28.70) 1.110 (28.19) 1.100 (27.94)18 1.178 (29.92) 1.172 (29.77) 1.055 (26.80) 1.049 (26.64) 1 1/8-28UN-2A 1.651 (41.94) 1.631 (41.43) 1.745 (44.32) 1.725 (43.82) 1.222 (31.04) 1.214 (30.84) 1
14、1/4-20UN-2A 1.265 (32.13) 1.255 (31.88) 1.235 (31.37) 1.225 (31.12)20 1.303 (33.10) 1.297 (32.94) 1.180 (29.97) 1.174 (29.82) 1 1/4-28UN-2A 1.776 (45.11) 1.756 (44.60) 1.870 (47.50) 1.850 (46.99) 1.347 (34.21) 1.339 (34.01) 1 3/8-20UN-2A 1.390 (35.31) 1.380 (35.05) 1.360 (34.54) 1.350 (34.29)22 1.42
15、8 (36.27) 1.422 (36.12) 1.305 (33.15) 1.299 (32.99) 1 3/8-28UN-2A 1.901 (48.29) 1.881 (47.78) 1.995 (50.67) 1.975 (50.17) 1.472 (37.39) 1.464 (37.19) 1 1/2-20UN-2A 1.515 (38.48) 1.505 (38.23) 1.485 (37.72) 1.475 (37.47)24 1.553 (39.45) 1.547 (39.29) 1.430 (36.32) 1.424 (36.17) 1 1/2-28UN-2A 2.026 (5
16、1.46) 2.006 (50.95) 2.120 (53.85) 2.100 (53.34) 1.597 (40.56) 1.589 (40.36) 1 5/8-20UN-2A 1.640 (41.66) 1.630 (41.40) 1.610 (40.89) 1.600 (40.64)TABLE 2A - FIGURE 1 DIMENSIONS/CONFIGURATION SHELL SIZE AR BSC BR BSC CR BSC DR BSC PANEL O-RING EE BSC POSITION 1 2 3 4 5 6 8 105 140 215 265 AS3582-018 6
17、0 46 43 60 89 43 10 95 141 208 236 AS3582-020 53 87 51 77 87 87 14 95 141 208 236 AS3582-024 53 87 51 77 87 87 16 80 142 196 293 AS3582-026 98 98 98 98 98 98 18 80 142 196 293 AS3582-028 98 98 98 98 98 98 20 80 142 196 293 AS3582-029 98 98 98 98 98 98 22 80 142 196 293 AS3582-030 98 98 98 98 98 98 2
18、4 80 142 196 293 AS3582-031 98 98 98 98 98 98 AEROSPACE STANDARD AS81511/49 SHEET 4 OF 4 REV. A CONNECTOR, RECEPTACLE, JAM NUT MOUNT, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, INDIVIDUAL RELEASE, CRIMP TYPE CONTACTS (CLASS A, F, AND W - SERIES 3) REQUIREMENTS: ALL
19、REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. 1. DESIGN: CONNECTORS SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE 2. DIMENSIONS ARE IN INCHES AND APPLY AFTER PLATING. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MM.
20、 UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE .016 INCHES. NORMAL MATING KEYWAY POSITION SHOWN IN FIGURE 1. FOR ALTERNATE KEYWAY POSITIONS, SEE AS81511, FIGURE 8. COLOR BANDS SHALL BE BLUE IN COLOR, .125 MAX. WIDTH AND SHALL BE VISIBLE WHEN MOUNTED. INSERT PROTRUSION FOR INSERTS CONTAINING SIZE 12 CON
21、TACTS SHALL BE .070/.020. SLOTTED NUT SHALL CONFORM TO AS81511/20. 2. FOR INSERT ARRANGEMENTS, SEE AS81511, APPENDIX A. 3. PART NUMBER: THE CONNECTOR PART NUMBER WILL CONSIST OF THE LETTER M, THE BASIC SPECIFICATION NUMBER/APPLICABLE SPECIFICATION SHEET, AND THE APPLICABLE ALPHA-NUMERIC CHARACTERS O
22、N THE CONNECTOR SHELL. THE PART NUMBER SHALL BE FORMULATED AS IN THE FOLLOWING EXAMPLE: M81511/49FD01P1. M81511/49 F D 01 P 1 BASIC PART NUMBER CLASS SHELL SIZE INSERT ARRANGEMENT CONTACT DESIGNATOR KEY POSITIONS 4. SHELL POLARIZATION: 1 THROUGH 6 KEY POSITION. 5. INSERTION AND REMOVAL TOOLS: AS8196
23、9/16 INSERTION/REMOVAL TOOL. 6. MATING CONNECTOR: THIS RECEPTACLE MATES DIRECTLY WITH AS81511/26 PLUG. APPLICATION NOTES: 1. AS81511 CONNECTORS AND ACCESSORIES ARE NOT RECOMMENDED FOR NEW DESIGN. SPECIFICATION NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL
24、. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
