1、AEROSPACE STANDARD CONNECTOR, PLUG, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING,CRIMP TYPE CONTACTS; AND ACCESSORIES (CLASS A, F, AND E - SERIES 2)AS81511/6Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a
2、 retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email:
3、CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2014-10THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 FEDERAL SUPPLY CLASS 5935AS81511/6SHEET 1 OF 3PROCUREMENT SPECIFICATION: AS81511SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of
4、 technicalandengineering sciences. Theuse ofthisreportis entirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, is thesole responsibilityoftheuser.”SAE reviews eachtechnicalreport at least every five years at which time itma
5、y berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81511/6RATIONALE THIS DETAIL SPECIFICATION SHEET IS WRITTEN TO PERMIT THE CANCELLA
6、TION AND SUPERSESSION OF MIL-C-81511/6 WITH THIS DOCUMENT. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. FIGURE 1 - CONNECTOR PLUG AEROSPACE STANDARD AS81511/6SHEET 2 OF 3CONNECTOR, PLUG, ELECTRICAL, CIRCUL
7、AR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, CRIMP TYPE CONTACTS; AND ACCESSORIES (CLASS A, F, AND E - SERIES 2)TABLE 1 - FIGURE 1 METRIC EQUIVALENTS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS .005 0.13 .235 5.97 1.035 26.29 .015 0.38 .240 6.10 1.100 27.94TABLE 2 - FIGURE
8、 1 DIMENSIONS SHELLSIZEADEFTHREADKAPBSCBPBSCCP BSCDP BSCJJ 8.3815(9.69).3755(9.54) .430(10.92) .424(10.77) .422(10.72) .407(10.34)1/2-28UNEF-2A.850(21.59) .830(21.08)128 - - - .382(9.70).373(9.47) 10.5065(12.87) .5005(12.71) .555(14.10) .549(13.94) .548(13.92) .533(13.54)5/8-28UN-2A .975(24.77) .955
9、24.26)105 140 215 265 .507(12.88) .498(12.65)14.7565(19.22) .7505(19.06) .805(20.45) .799(20.29) .798(20.27) .783(19.89)7/8-28UN-2A 1.225(31.12) 1.205(30.61)105 140 215 265 .757(19.23) .746(18.95)16.8825(22.42) .8765(22.26) .930(23.63) .924(23.47) .924(23.47) .909(23.09)1-28UN-2A 1.350(34.29) 1.330
10、33.78)105 140 215 265 .883(22.43) .872(22.15)181.0065(25.571.0005(25.41) 1.055(26.80) 1.049(26.64) 1.048(26.62) 1.033(26.24)1 1/8-28UN-2A1.475(37.47) 1.455(36.96)105 140 215 265 1.007(25.58) .996(25.30)REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. 1.
11、 DESIGN: CONNECTORS SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE 2. DIMENSIONS ARE IN INCHES AND ARE AFTER PLATING. METRIC EQUIVALENTS ARE GIVEN FOR INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MM. UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE .016 INCHES. THE NORMAL MATING KEYWAY POSITIO
12、N IS SHOWN IN FIGURE 1. FOR ALTERNATE KEYWAY POSITIONS, SEE AS81511 FIGURE 4. CONNECTORS ARE SERIES 2, CLASSES ARE A, F, AND E. CONTACTS ARE CRIMP TYPE REMOVABLE, STYLE P AND S. 2. FOR INSERT ARRANGEMENTS, SEE AS81511, APPENDIX A. 3. PART NUMBER: THE CONNECTOR PART NUMBER WILL CONSIST OF THE LETTER
13、M, THE BASIC SPECIFICATION NUMBER/APPLICABLE SPECIFICATION SHEET, AND THE APPLICABLE ALPHA-NUMERIC CHARACTERS ON THE CONNECTOR SHELL. THE PART NUMBER SHALL BE FORMULATED AS IN THE FOLLOWING EXAMPLE: M81511/06ED01P1. M81511/06 E D 01 P 1 BASIC PART NUMBERCLASSSHELL SIZE INSERT ARRANGEMENT CONTACT DES
14、IGNATOR KEY POSITIONS AEROSPACE STANDARD AS81511/6SHEET 3 OF 3CONNECTOR, PLUG, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, CRIMP TYPE CONTACTS; AND ACCESSORIES (CLASS A, F, AND E - SERIES 2)4. SHELL POLARIZATION: 1 THROUGH 6 KEY POSITION. 5. INSERTION AND REMOVAL TOO
15、LS: AS81969/2 INSERTION TOOL, AS81969/3 REMOVAL TOOL. 6. MATING CONNECTOR: THIS PLUG MATES DIRECTLY WITH AS81511/1, /3, AND /5 RECEPTACLES. 7. CONNECTOR WEIGHT: THE CONNECTOR REFERENCE WEIGHTS ARE LISTED IN TABLE 3. TABLE 3 - CONNECTOR WEIGHT SHELL SIZE WEIGHT (REFERENCE - POUNDS) 1/ 18 (CODE F) .08
16、0 16 (CODE E) .067 14 (CODE D) .056 10 (CODE B) .035 8 (CODE A) .027 1/ CONTACTS NOT INCLUDED IN WEIGHT. APPLICATION NOTES: 1. FOR SHELL SIZES 20, 22, AND 24, USE AS81511/26 CONNECTORS. 2. AS81511 CONNECTORS AND ACCESSORIES ARE NOT RECOMMENDED FOR NEW DESIGN. SPECIFICATION NOTES: NOTICE THIS DOCUMEN
17、T REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
