1、 AEROSPACE STANDARD CONNECTORS, ELECTRICAL, RECTANGULAR, PLUG, CRIMP CONTACTS (SINGLE INSERT, TYPE II, CLASS 1, (-65 C TO +125 C), SERIES 2, SHELL DESIGNATOR A) AS81659/29Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system
2、 or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesa
3、e.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2004-05REVISED 2017-06THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.B FEDERAL SUPPLY CLASS 5935 AS81659 /29 SHEET 1 OF 3 REV. B PROCUREMENT SPECIFICATION: AS81659 SAE Technical Standards Board Rules provide that: “This report is published by SAEtoad
4、vance thestate of technicaland engineering sciences. The useof this report is entirely voluntary, and its applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,is thesole responsibility of theuser.” SAE reviews eachtechnical reportatleast every fiveyea
5、rs at whichtime it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS81659/29B RATIONALE REVISION IS REQUIRED TO UPDATE THE CONNECTOR INSE
6、RT AND INSTALLING/REMOVAL TOOL REFERENCES. FIGURE 1 CONNECTOR SUGGESTED PANEL CUTOUT/RECOMMENDED MATED POSITION INCHES MM INCHES MM INCHES MM INCHES MM INCHES MM .006 .047 .060 .115 .117 .118 .122 .125 .15 1.19 1.52 2.92 2.97 3.00 3.10 3.18 .133 .178 .198 .281 .297 .521 .541 3.38 4.52 5.03 7.14 7.54
7、 13.23 13.74 .550 .7185 .720 .885 .897 .928 .948 13.97 18.25 18.29 22.48 22.78 23.57 24.08 1.000 1.175 1.367 1.387 1.427 1.430 1.437 1.447 25.40 29.84 34.72 35.23 36.25 36.32 36.50 36.75 1.541 1.720 1.730 1.985 2.015 2.032 2.062 2.320 39.14 43.69 43.94 50.42 51.18 51.61 52.37 58.93 AEROSPACE STANDAR
8、D AS81659/29 SHEET 2 OF 3 REV. B CONNECTORS, ELECTRICAL, RECTANGULAR, PLUG, CRIMP CONTACTS (SINGLE INSERT, TYPE II, CLASS 1, (-65 C TO +125 C), SERIES 2, SHELL DESIGNATOR A) FIGURE 2 CONNECTOR CONFIGURATIONS AND DIMENSIONS AEROSPACE STANDARD AS81659/29 SHEET 3 OF 3 REV. B CONNECTORS, ELECTRICAL, REC
9、TANGULAR, PLUG, CRIMP CONTACTS (SINGLE INSERT, TYPE II, CLASS 1, (-65 C TO +125 C), SERIES 2, SHELL DESIGNATOR A) FIGURE 2 CONNECTOR CONFIGURATIONS AND DIMENSIONS (CONTINUED) REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81659. 1. DESIGN: CONNECTOR ACCESSORI
10、ES SHALL BE DESIGNED IN ACCORDANCE WITH FIGURES 1 AND 2. DIMENSIONS ARE IN INCHES AND APPLY AFTER PLATING. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED UPON 1 INCH = 25.4 MM. NORMAL (01) POLARIZATION POSITION SHOWN, FOR ALTERNATE POSITIONS SEE AS81659. FOR LOCATION OF DATU
11、MS G AND H, REFER TO AS81659 FIGURE 4. 2. INSERT ARRANGEMENTS SHALL BE IN ACCORDANCE WITH AS31571. 3. CONTACTS SHALL BE IN ACCORDANCE WITH AS39029/11 OR AS39029/12 AS APPLICABLE. 4. INSTALLING AND REMOVAL TOOLS SHALL BE IN ACCORDANCE WITH AS81969/1 OR AS81969/14. SPECIFICATION NOTES 1. REVISION INDI
12、CATOR: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
