1、AEROSPACE STANDARD TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, WIRE IN-LINE JUNCTIONS, DOUBLE, SERIES I AS81714/12Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any
2、 means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.o
3、rg ISSUED 1998-07REAFFIRMED 2004-11 REVISED 2010-10THIRD ANGLE PROJECTION CUSTODIAN: AE-8C2 REV.AFEDERAL SUPPLY CLASS 5940 AS81714/12SHEET 1 OF 2REV. APROCUREMENT SPECIFICATION: AS81714SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicaland
4、engineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffi
5、rmed, revised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81714/12ARATIONALE INCORPORATE AS81714/12-A1 AND UPDATE REFERENCES. FIGURE 1 DOUBLE WIRE IN-LINE JUNCTI
6、ON BOX Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS81714/12SHEET 2 OF 2REV. ATERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, WIRE IN-LINE JUNCTIONS, DOUBLE, SE
7、RIES I TABLE 1 IN-LINE JUNCTIONS PART NUMBER 1/TYPE IN-LINE JUNCTION CONSISTS OF INSTALLING/ REMOVAL TOOL SEE NOTE 2 BODY CONTACTS AMAXBMAXC.01 LMAXPART NUMBER M81714/12-22*-* 1OR 2.400 .275 .13 1.552 M39029/1-100 M81969/14-01 M81714/12-20*-* .400 .275 .13 1.552 M39029/1-101 M81969/14-10M81969/14-11
8、 M81714/12-16*-* .500 .300 .18 1.922 M39029/1-102 M81969/14-03M81714/12-12*-* .620 .370 .25 1.922 M39029/1-103 M81969/14-04 1/ SEE NOTE 6. INCH mm INCH mm .130 3.30 .400 10.2 .180 4.57 .500 12.7 .250 6.35 .620 15.7 .275 6.99 1.552 39.42 .300 7.62 1.922 48.82 .370 9.40 NOTES: 1. DIMENSIONS ARE IN INC
9、HES. 2. TOOL FOR CONTACT INSERTING/REMOVAL SHALL BE APPROPRIATE SIZE M81969/14 AND SHALL BE ORDERED SEPARATELY (SEE TABLE 1). 3. METRIC EQUIVALENTS (TO THE NEAREST .01 MM) ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED UPON 1 INCH = 25.4 MM. 4. INTERNATIONAL INTEREST, SEE SPECIFICATION AS81714
10、 5. THE PART NUMBER CONSISTS OF THE LETTER M, SPECIFICATION SHEET NUMBER, COMPONENT SIZE, CLASS, AND TYPE DESIGNATOR. PART NUMBER EXAMPLE: M81714/12-12D-2 SIZE 12, CLASS D, TYPE 2 WIRE IN-LINE JUNCTION. 6. CLASSES A, B AND C COMPONENTS ARE INACTIVE FOR NEW DESIGN. ONLY CLASS D COMPONENTS SHALL BE U
11、SED FOR DIRECT GOVERNMENT ACQUISITION. 7. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES
12、 A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
