1、 AEROSPACE STANDARD REMOVAL TOOLS, CONNECTOR, ELECTRICAL CONTACT, (FORK TYPE, WRAPPOST/CRIMP REMOVABLE) TYPE II, CLASS 1, COMPOSITION C AS81969/11Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any f
2、orm or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: ht
3、tp:/www.sae.org ISSUED 2015-06THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5120AS81969/11 SHEET 1 OF 3 PROCUREMENT SPECIFICATION: AS81969SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. The
4、use ofthisreport is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, or
5、cancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81969/11 RATIONALE THIS DETAIL SPECIFICATION SHEET IS REQUIRED TO ALLOW THE CANCELLATION AND SUPERSESSION OF MIL-I-81969
6、/11 WITH THIS DOCUMENT, TO IMPROVE DRAWING LEGIBILITY, TO INCORPORATE AMENDMENT 1, TO REMOVE THE PATENT NOTICE SINCE THE PATENT HAS EXPIRED, TO UPDATE QUALIFICATION INFORMATION, AND TO UPDATE REFERENCES. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THI
7、S DOCUMENT AND THE LATEST ISSUE OF AS81969. FIGURE 1 - REMOVAL TOOL CONFIGURATIONS/DIMENSIONS AEROSPACE STANDARD AS81969/11 SHEET 2 OF 3 REMOVAL TOOLS, CONNECTOR, ELECTRICAL CONTACT, (FORK TYPE, WRAPPOST/CRIMP REMOVABLE) TYPE II, CLASS 1, COMPOSITION C TABLE 1 - METRIC EQUIVALENTS INCHES MILLIMETERS
8、 INCHES MILLIMETERS INCHES MILLIMETERS .001 0.03 .120 3.05 1.125 28.58 .002 0.05 .250 6.35 1.140 28.96 .020 0.51 .450 11.43 1.5 38.10 .030 0.76 .580 14.73 6.200 157.48.066 1.68 .625 15.88 REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81969. 1. DESIGN: THE TO
9、OL SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1. DIMENSIONS ARE IN INCHES. METRIC EQUIVALENTS IN TABLE 1 ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MILLIMETERS. UNLESS OTHERWISE SPECIFIED, TOLERANCE IS .015 INCH (0.38 MILLIMETERS). 2. COMPONENTS: THE PROBE AND PLUNGER SHA
10、LL BE PERMANENTLY ATTACHED TO THE BODY OF THE TOOL, THEREFORE THE TOOL IS NON-REPAIRABLE. THE CLIP RELEASE PRONGS SHALL MAINTAIN ALIGNMENT IN ORDER TO PREVENT DAMAGE TO THE CONNECTOR CONTACT CAVITY. THE PLUNGER SHALL SELF-RETURN TO THE UNUSED POSITION. 3. MATERIAL AND FINISHES: HANDLE AND INSERT - A
11、LUMINUM ALLOY, PLASTIC IN ACCORDANCE WITH ASTM D5948, ASTM D4673, OR AN ALTERNATE MATERIAL APPROVED BY THE QUALIFYING ACTIVITY. BLADE - 1090 STEEL, SPRING TEMPERED, STEEL SAE 4130, AMS5643, AMS6370, 400 SERIES STAINLESS STEEL OR 300 MARGING STEEL OR SUITABLE MATERIAL, HEAT TREATED TO ROCKWELL C35-45
12、 PLATING - FOR NON-CORROSION RESISTANT STEELS, COAT WITH ELECTROLESS NICKEL TO THE REQUIREMENTS OF AMS2404, CLASS I (THICKNESS .0002 TO .0005). HYDROGEN RELIEF FOR 4 HOURS 1 HOUR AT 375 F 25 F, WITHIN 24 HOURS AFTER COATING, TREAT BY IMMERSION IN A SOLUTION IN ACCORDANCE WITH MIL-DTL-5541 TO ENHANC
13、E RESISTANCE TO CORROSION AND TARNISH OR NICKEL PLATING (ELECTRODEPOSITED) IN ACCORDANCE WITH AMS-QQ-N-290, CLASS 2, THICKNESS .0002 TO .0005). 4. PART NUMBER/MARKING: M81969/11-01 EACH TOOL SHALL BE LEGIBLY AND PERMANENTLY MARKED ON THE HANDLE WITH THE MANUFACTURERS IDENTIFICATION AND PART NUMBER I
14、N ACCORDANCE WITH MIL-STD-130. MANUFACTURER SYMBOL, IF USED, SHALL BE IN ACCORDANCE WITH AIR1351. 5. QUALIFICATION: QUALIFICATION SHALL BE IN ACCORDANCE WITH AS81969 WITH THE FOLLOWING EXCEPTIONS: PLUNGER FORCE - 5 POUNDS MAXIMUM ROTATION - NOT APPLICABLE THRUST - NOT APPLICABLE IMPACT STRENGTH - NO
15、T APPLICABLE PLUNGER FORCE - NOT APPLICABLE ALTERNATIVE QUALIFICATION REQUIREMENTS SUCH AS CERTIFICATION, FIRST ARTICLE OR QC TESTING MAY BE IMPOSED BY THE QUALIFYING ACTIVITY (QA). THE QA SHALL SUBMIT A WRITTEN REQUEST TO THE AE-8C2 COMMITTEE FOR REVIEW AND APPROVAL OF THE ALTERNATIVE QUALIFICATION
16、 TESTING PROGRAM PRIOR TO IMPLEMENTATION OF THE REQUIREMENT. APPLICATION NOTES: 1. THIS TOOL SHALL BE USED TO REMOVE CONTACTS SPECIFIED IN MIL-DTL-28731/1 THROUGH /6 AND /9 THROUGH /18. 2. THIS DOCUMENT SUPERSEDES MIL-I-81969/11B DATED 25 JANUARY 1985, MIL-I-81969/11B AMENDMENT 1 DATED 27 FEBRUARY 1
17、997, AND MIL-C-28731/22B DATED 12 MAY 1977. AEROSPACE STANDARD AS81969/11 SHEET 3 OF 3 REMOVAL TOOLS, CONNECTOR, ELECTRICAL CONTACT, (FORK TYPE, WRAPPOST/CRIMP REMOVABLE) TYPE II, CLASS 1, COMPOSITION C SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE
18、 USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
