1、AEROSPACE STANDARD INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE I, CLASS 1, COMPOSITION C AS81969/18Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, elect
2、ronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 201
3、3-10THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5120 AS81969/18SHEET 1 OF 2PROCUREMENT SPECIFICATION: AS81969SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirel
4、y voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites y
5、ourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81969/18RATIONALE AS81969/18 PERMITS THE CANCELLATION AND SUPERSESSION OF MIL-I-81969/18 WITH THIS DOCUMENT. IT INCLUDES ENGINEERING POSITION LE
6、TTERS, MILITARY SPECIFICATION AMENDMENTS, AND MINOR TECHNICAL CHANGES REQUIRED TO REFLECT THE APPROVED QUALIFIED TOOLS. GOVERNMENT DOCUMENTATION REFERENCES ARE REMOVED. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF
7、AS81969. FIGURE 1 - INSTALLING TOOL AEROSPACE STANDARD AS81969/18SHEET 2 OF 2INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE I, CLASS 1, COMPOSITION C REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF AS81969. 1. CONFIGURATION: a. TOOL CONFIG
8、URATION SHALL BE IN ACCORDANCE WITH FIGURE 1. b. DIMENSIONING AND TOLERANCES IN ACCORDANCE WITH ANSI Y14.5M. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCE IS .05. c. HANDLE CONFIGURATION OPTIONAL WITHIN DIMENSIONS SHOWN. d. EACH TOOL SHALL BE FURNISHED WITH A PROBE PROTECTIVE CAP.
9、THE CAP DESIGN AND MATERIAL IS OPTIONAL (SEE APPLICATION NOTE). 2. IDENTIFICATION MARKING: EACH TOOL SHALL BE LEGIBLY AND PERMANENTLY MARKED ON TOOL HANDLE IN ACCORDANCE WITH MIL-STD-130 (LOCATION OPTIONAL). MARKING SHALL INCLUDE MANUFACTURER NAME OR SYMBOL, MANUFACTURER PART NUMBER, AND SAE PART ID
10、ENTIFICATION NUMBER (PIN). SUPPLIER SYMBOL, IF USED, SHALL BE IN ACCORDANCE WITH AIR1351. 3. MATERIALS: HANDLE SHALL BE PLASTIC OR ALUMINUM PROBES SHALL BE STAINLESS STEEL 4. SAE PART IDENTIFICATION NUMBER (PIN): M81969 /18 -01 I I I I I I_ DASH NUMBER (-01 or -02) I I_ DETAIL SPECIFICATION NUMBER I
11、 BASIC SPECIFICATION NUMBER APPLICATION NOTES: 1. TOOLS SHALL BE USED TO INSTALL CONTACTS IN CONNECTORS SPECIFIED IN TABLE 1. TABLE 1 - TOOL APPLICATION PART NUMBER M81969/18 CONTACT SIZE CONNECTOR -01 16 & 20 MIL-DTL-28748 -02 22 2. TOOL SUPERSEDING PART NUMBERS ARE SHOWN TABLE 2. AS81969/18 DETAI
12、L SPECIFICATION SUPERSEDES MIL-I-81969/18A DETAIL SPECIFICATION. PART NUMBERS REMAIN UNCHANGED. TABLE 2 - TOOL PART NUMBER SUPERSESSION PART NUMBER M81969/18 SUPERSEDED PART NUMBERS -01 N/A -02 MS178053. THE PROTECTIVE CAP (SEE FIGURE 1) MINIMIZES DAMAGE TO THE TIP AND IMPROVES PERSONNEL SAFETY. IF
13、LOST, CONTACT THE SUPPLIER FOR REPLACEMENT. SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
