1、 AEROSPACE STANDARD REMOVAL TOOLS, CONNECTOR, ELECTRICAL CONTACT, TYPE II, CLASS 1, COMPOSITION B AS81969/29Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mecha
2、nical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2015-06THIRD AN
3、GLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5120AS81969/29 SHEET 1 OF 3 PROCUREMENT SPECIFICATION: AS81969SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport is entirelyvoluntary,
4、 andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomm
5、ents andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81969/29 RATIONALE THIS DETAIL SPECIFICATION SHEET IS REQUIRED TO ALLOW THE CANCELLATION AND SUPERSESSION OF MIL-I-81969/29 WITH THIS DOCUMENT, TO IMPROVE DRA
6、WING LEGIBILITY, TO UPDATE QUALIFICATION INFORMATION, TO REMOVE GOVERNMENT JARGON, AND TO UPDATE REFERENCES. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81969. DETAIL X FIGURE 1 - REMOVAL TOOL CONFIGURATIONS/DIM
7、ENSIONS (DASH -02, -03, AND -04) AEROSPACE STANDARD AS81969/29 SHEET 2 OF 3 REMOVAL TOOLS, CONNECTOR, ELECTRICAL CONTACT, TYPE II, CLASS 1, COMPOSITION B FIGURE 2 - REMOVAL TOOL CONFIGURATIONS/DIMENSIONS (DASH -01) TABLE 1 - FIGURE 1 AND 2 CONFIGURATIONS/DIMENSIONS/SUPERSEDING PART NUMBERS DASH NUMB
8、ER WIRE BARREL SIZE COLOR CODE A MAX. B DIA. C DIA. D MAX. F MAX. H K MIN. L MIN. M DIA. SUPERSEDED PART NUMBER -01 16 BLUE .425 (10.80) .195 (4.95) .185 (4.70) .105 (2.67) .100 (2.54) .160 (4.06) 5.000 (127.00).0175 (0.44) .0135 (0.34) 1.100 (27.94) .390 (9.91) .340 (8.64) .320 (8.13) MS3165-16 -02
9、 8 RED .641 (16.28) .420 (10.67) .410 (10.41) .274 (6.96) .271 (6.88) .315 (8.00) 5.000 (127.00) .021 (0.53) .016 (0.41) 1.690 (42.93) .585 (14.86) .575 (14.61) .540 (13.72) MS3165-8 M83723/32-08-03 4 BLUE .875 (22.23) .620 (15.75) .610 (15.49) .385 (9.78) .383 (9.73) .410 (10.41) 5.000 (127.00) .02
10、0 (0.51) .018 (0.46) 1.690 (42.93) .585 (14.86) .745 (18.92) .735 (18.67) MS3165-4 M83723/32-04-04 0 YELLOW 1.219 (30.96) .950 (24.13) .945 (24.00) .581 (14.76) .579 (14.71) .615 (15.62) 5.000 (127.00) .027 (0.69) .020 (0.51) 2.090 (53.09) .785 (19.94) 1.095 (27.81) 1.085 (27.56) MS3165-0 M83723/32-
11、00REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81969. 1. DESIGN: THE TOOL SHALL BE DESIGNED IN ACCORDANCE WITH FIGURES 1 AND 2 AND TABLE 1. DIMENSIONS ARE IN INCHES. METRIC EQUIVALENTS IN TABLE 1 ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 1 INC
12、H = 25.4 MILLIMETERS. UNLESS OTHERWISE SPECIFIED, TOLERANCE IS .005 INCH (0.13 MILLIMETERS). THE SLOT DESIGN SHALL ALLOW ALL APPLICABLE WIRE SIZES TO SNAP IN TOOL FREELY. 2. MATERIAL AND FINISHES: MATERIAL - MOLDED ACETAL, POLYAMIDE, OR APPROVED EQUIVALENT PLATING - NOT APPLICABLE AEROSPACE STANDARD
13、 AS81969/29 SHEET 3 OF 3 REMOVAL TOOLS, CONNECTOR, ELECTRICAL CONTACT, TYPE II, CLASS 1, COMPOSITION B 3. PART NUMBER/MARKING: SEE EXAMPLE BELOW: M81969 /29 -01 BASE SPECIFICATION DETAIL SHEET DASH NUMBER EACH TOOL SHALL BE LEGIBLY AND PERMANENTLY MARKED ON THE HANDLE WITH THE MANUFACTURERS IDENTIFI
14、CATION AND PART NUMBER IN ACCORDANCE WITH MIL-STD-130. MANUFACTURER SYMBOL, IF USED, SHALL BE IN ACCORDANCE WITH AIR1351. 4. QUALIFICATION: QUALIFICATION SHALL BE IN ACCORDANCE WITH AS81969 WITH THE FOLLOWING EXCEPTIONS: PLUNGER FORCE - NOT APPLICABLE ALTERNATIVE QUALIFICATION REQUIREMENTS SUCH AS C
15、ERTIFICATION, FIRST ARTICLE OR QC TESTING MAY BE IMPOSED BY THE QUALIFYING ACTIVITY (QA). THE QA SHALL SUBMIT A WRITTEN REQUEST TO THE AE-8C2 COMMITTEE FOR REVIEW AND APPROVAL OF THE ALTERNATIVE QUALIFICATION TESTING PROGRAM PRIOR TO IMPLEMENTATION OF THE REQUIREMENT. APPLICATION NOTES: 1. THIS TOOL
16、 SHALL BE USED TO REMOVE CONTACTS FOR AS50151, AS345X SERIES CONNECTORS. 2. THIS DOCUMENT SUPERSEDES MS3165A DATED 23 MAY 1973, MIL-C-83723/32 DATED 12 OCTOBER 1971, AND MIL-I-81969/29 DATED 11 JANUARY 1979. SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE O
17、F THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
