1、AEROSPACE STANDARD INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE II, CLASS 1, COMPOSITION A (FOR MIL-DTL-28840 CONNECTORS)AS81969/34Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in
2、any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRES
3、S: http:/www.sae.org ISSUED 2014-07THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5120 AS81969/34SHEET 1 OF 2PROCUREMENT SPECIFICATION: AS81969SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineeringsciences.Th
4、e useofthis reportisentirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, o
5、rcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81969/34RATIONALE AS81969/34 PERMITS THE CANCELLATION AND SUPERSESSION OF MIL-I-81969/34F (EC) WITH THIS DOCUMENT. IT I
6、NCLUDES ENGINEERING POSITION LETTERS, MILITARY SPECIFICATION AMENDMENTS, AND MINOR TECHNICAL CHANGES REQUIRED TO REFLECT THE APPROVED QUALIFIED TOOLS. GOVERNMENT DOCUMENTATION REFERENCES ARE REMOVED. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCTS DESCRIBED HEREIN SHALL CONSIST OF THIS D
7、OCUMENT AND THE LATEST ISSUE OF AS81969. FIGURE 1 - REMOVAL TOOL AEROSPACE STANDARD AS81969/34SHEET 2 OF 2INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE II, CLASS 1, COMPOSITION A (FOR MIL-DTL-28840 CONNECTORS) REQUIREMENTS - ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE
8、LATEST ISSUE OF AS81969. 1. CONFIGURATION a. TOOL CONFIGURATION SHALL BE IN ACCORDANCE WITH FIGURE 1. b. DIMENSIONING AND TOLERANCES IN ACCORDANCE WITH ANSI Y14.5M. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCE IS .05. c. PLUNGER SHALL BE SPRING LOADED WITH A RETRACTION FORCE OF 1.
9、5 POUNDS 1.0 POUNDS. d. TOOL TIP SHALL BE REPLACEABLE (SEE APPLICATION NOTE). e. TOOL TIP .071 GO/ .072 NO-GO SHALL BE APPLICABLE FOR .952 MINIMUM LENGTH (SEE APPLICATION NOTE). f. EACH TOOL SHALL BE FURNISHED WITH A PROBE PROTECTIVE CAP. THE CAP DESIGN, MATERIAL AND COLOR ARE OPTIONAL (SEE APPLICAT
10、ION NOTE). 2. IDENTIFICATION MARKING EACH TOOL SHALL BE LEGIBLY AND PERMANENTLY LASER MARKED ON TOOL HANDLE IN ACCORDANCE WITH MIL-STD-130 (LOCATION OPTIONAL). MARKING SHALL INCLUDE MANUFACTURER NAME OR SYMBOL, MANUFACTURER PART NUMBER, AND SAE PART IDENTIFICATION NUMBER (PIN). SUPPLIER SYMBOL, IF U
11、SED, SHALL BE IN ACCORDANCE WITH AIR1351. 3. MATERIALS a. PROBE SHALL BE 410 OR 420 STAINLESS STEEL HARDENED TO ROCKWELL C48-52 AND FREE FROM NICKS AND BURRS. b. PLUNGER SHALL BE STAINLESS STEEL IN ACCORDANCE WITH AS81969. c. HANDLE AND BODY SHALL BE ALUMINUM ALLOY. HANDLE SHALL BE RED ANODIZED. 4.
12、SAE PART IDENTIFICATION NUMBER (PIN) M81969 /34 -01 I I I I I I_ DASH NUMBER I I_ DETAIL SPECIFICATION NUMBER I_ BASIC SPECIFICATION NUMBER APPLICATION NOTES: 1. TOOL TIP .071 GO/ .072 NO-GO DIMENSIONS MAY BE MEASURE WITH A TEST PIN WITH -.0000 TO +.0002 INCH TOLERANCE FOR A .952 INCH MINIMUM LENGTH
13、 2. THE PROTECTIVE CAP (SEE FIGURE 1) MINIMIZES DAMAGE TO THE TIP AND IMPROVES PERSONNEL SAFETY. IF LOST, CONTACT THE QUALIFIED SUPPLIER FOR REPLACEMENT. 3. TOOL SHALL BE USED TO REMOVE CONTACTS IN MIL-DTL-28840 CONNECTORS. 4. M81969/34 SUPERSEDES MIL-I-81969/34F (EC). THE PART NUMBER REMAINS UNCHA
14、NGED. SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
