1、 AEROSPACE STANDARD REMOVAL TOOLS, CONNECTOR, ELECTRICAL CONTACT, (TYPE CR CONNECTOR) TYPE II, CLASS 1, COMPOSITION AAS81969/6Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means,
2、 electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSU
3、ED 2015-06THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS AS81969/6 SHEET 1 OF 2 PROCUREMENT SPECIFICATION: AS81969SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport is entir
4、elyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yo
5、urwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81969/6 RATIONALE THIS DETAIL SPECIFICATION SHEET IS REQUIRED TO ALLOW THE CANCELLATION AND SUPERSESSION OF MIL-I-81969/6 WITH THIS DOCUMENT, TO
6、IMPROVE DRAWING LEGIBILITY, TO UPDATE QUALIFICATION INFORMATION, TO REMOVE GOVERNMENT JARGON, AND TO UPDATE REFERENCES. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81969. FIGURE 1 - TOOL CONFIGURATION AND DIMENS
7、IONS AEROSPACE STANDARD AS81969/6 SHEET 2 OF 2 REMOVAL TOOLS, CONNECTOR, ELECTRICAL CONTACT, (TYPE CR CONNECTOR) TYPE II, CLASS 1, COMPOSITION A TABLE 1 - METRIC EQUIVALENTS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS .001 0.025 .030 0.762 .400 10.16 .002 0.051 .050 1.27 .418 10.62 .003
8、 0.762 .052 1.32 .425 10.80 .004 0.102 .062 1.57 3.000 76.20.006 0.152 .076 1.93 4.250 107.95 .010 0.254 .109 2.77 .020 0.508 .175 4.44 REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81969. 1. DESIGN: THE TOOL SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1. DI
9、MENSIONS ARE IN INCHES. METRIC EQUIVALENTS IN TABLE 1 ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MILLIMETERS. UNLESS OTHERWISE SPECIFIED, TOLERANCE IS .005 INCH (0.13 MILLIMETERS). 2. COMPONENTS: THE PROBE AND PLUNGER SHALL BE PERMANENTLY ATTACHED TO THE BODY OF THE TOOL,
10、THEREFORE THE TOOL IS NON-REPAIRABLE. 3. MATERIAL: CORROSION RESISTANT STEEL IN ACCORDANCE WITH AS81969. 4. FINISH: BLACKENED 5. PART NUMBER/MARKING: M81969/6-01 EACH TOOL SHALL BE LEGIBLY AND PERMANENTLY MARKED ON THE HANDLE WITH THE MANUFACTURERS IDENTIFICATION AND PART NUMBER IN ACCORDANCE WITH M
11、IL-STD-130. MANUFACTURER SYMBOL, IF USED, SHALL BE IN ACCORDANCE WITH AIR1351. 6. QUALIFICATION: QUALIFICATION SHALL BE IN ACCORDANCE WITH AS81969 WITH THE FOLLOWING EXCEPTIONS: ROTATION - NOT APPLICABLE THRUST - NOT APPLICABLE IMPACT STRENGTH - NOT APPLICABLE ALTERNATIVE QUALIFICATION REQUIREMENTS
12、SUCH AS CERTIFICATION, FIRST ARTICLE OR QC TESTING MAY BE IMPOSED BY THE QUALIFYING ACTIVITY (QA). THE QA SHALL SUBMIT A WRITTEN REQUEST TO THE AE-8C2 COMMITTEE FOR REVIEW AND APPROVAL OF THE ALTERNATIVE QUALIFICATION TESTING PROGRAM PRIOR TO IMPLEMENTATION OF THE REQUIREMENT. APPLICATION NOTES: 1.
13、THIS TOOL SHALL BE USED TO REMOVE CONTACTS CONFORMING TO MIL-DTL-21097/16 AND /17 WHEN ASSEMBLED IN CONNECTORS CONFORMING TO MIL-DTL-21097/13. 2. THIS DOCUMENT SUPERSEDES MIL I-81969/6B DATED 2 OCTOBER 1980 AND MIL-C-21097/18C DATED 10 OCTOBER 1972. SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED I
14、N THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
