1、 AEROSPACE STANDARD CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, NONENVIRONMENTAL, STRAIGHT, SHIELDED TERMINATION, THREADED APAPTER, CATEGORY 7 (FOR MIL-DTL-38999 SERIES I AND II CONNECTORS) AS85049/33Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduce
2、d, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-77
3、6-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2000-05REVISED2012-04REAFFIRMED 2017-05THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.C FEDERAL SUPPLY CLASS 5935 AS85049 SHEET 1 OF 4 REV. C PROCUREMENT SPECIFICATION: AS85049 6$(7HFKQLFDO6WDQGDUGV%RDUG5XOHVSURYLGHWKDW
4、7KLVUHSRUWLVSXEOLVKHGE6$(WRDGYDQFHWKHVWDWHRIWHFKQLFDODQGHQJLneering sciences. The useof this report is entirely voluntary, and its applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,LVWKHVROHUHVSRQVLELOLWRIWKHXVHUSAE reviews eachtechnical reportatle
5、ast every fiveyears at whichtime it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS85049/33C RATIONALE AS85049/33C HAS BEEN REAFFIRMED
6、TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTICE THE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF SAE AS85049. ADAPTER - 1 FIGURE 1 - DIMENSIONS AND CONFIGURATION (SEE TABLE 1) AEROSPACE STANDARD AS85049/33 SHEET 2 OF
7、 4 CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, NONENVIRONMENTAL, STRAIGHT, SHIELDED TERMINATION, THREADED APAPTER, CATEGORY 7 (FOR MIL-DTL-38999 SERIES I AND II CONNECTORS) REV. C FIGURE 2 - DIMENSIONS AND CONFIGURATION (SEE TABLE 2) AEROSPACE STANDARD AS85049/33 SHEET 3 OF 4 CONNECTOR ACCESSORIES
8、 ELECTRICAL, BACKSHELL, NONENVIRONMENTAL, STRAIGHT, SHIELDED TERMINATION, THREADED APAPTER, CATEGORY 7 (FOR MIL-DTL-38999 SERIES I AND II CONNECTORS) REV. C NOTES: 1. DIMENSIONS ARE IN INCHES AND APPLY AFTER PLATING. 2. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY. 3. CRIMP TOOL SHALL
9、BE THOMAS & BETTS INSTALLING HEAD CAT. NO. 13640 OR EQUIVALENT AND INSTALLING DIES. REQUIREMENTS: DESIGN AND CONSTRUCTION: DIMENSIONS AND CONFIGURATION: SEE FIGURES 1 AND 2, AND TABLES 1 AND 2. STRAIGHT ADAPTER (FIGURE 1) MAY BE OF TWO-PIECE CONSTRUCTION. METHOD OF JOINING IS OPTIONAL. INTERFACE DIM
10、ENSIONS SHALL CONFORM TO SAE AS85049, FIGURE 2. THE COUPLING NUT SHALL BE CAPTIVATED TO AND FREE TO ROTATE ON THE BODY. PARTS SUPPLIED TO FIGURE 2 SHALL CONSIST OF A COUPLING NUT AND BODY AS SHOWN, ALONG WITH THE APPROPRIATE AS85049/26-2 SHIELD CRIMP RING FROM TABLE 2. MATERIAL AND FINISH SHALL BE A
11、S SPECIFIED IN TABLE 3. TABLE 1 - SHELL SIZE AND DIMENSIONS (FOR FIGURE 1) ADAPTER SHELL SIZE FITS CONNECTOR SHELL SIZE A MAXIMUM DIAMETER B MAXIMUM DIAMETER C MAXIMUM DIAMETER LS MAXIMUM V THREAD UNEF CLASS 2B SERIES II SERIES I 8 8 9 .594 (15.09) .359 (9.12) .516 (13.11) .844 (21.44) .4375-28 10 1
12、0 11 .719 (18.26) .406 (10.31) .641 (16.28) .969 (24.61) .5625-24 12 12 13 .844 (21.44) .500 (12.70) .766 (19.46) 1.094 (27.79) .6875-24 14 14 15 .969 (24.61) .578 (14.68) .891 (22.63) 1.156 (29.36) .8125-20 16 16 17 1.094 (27.79) .641 (16.28) 1.016 (25.81) 1.219 (30.96) .9375-20 18 18 19 1.219 (30.
13、96) .688 (17.48) 1.141 (28.98) 1.344 (34.14) 1.0625-18 20 20 21 1.344 (34.14) .734 (18.64) 1.265 (32.13) 1.469 (37.31) 1.1875-18 22 22 23 1.469 (37.31) .796 (20.22) 1.391 (35.33) 1.594 (40.49) 1.3125-18 24 24 25 1.594 (40.49) .859 (21.82) 1.516 (38.51) 1.719 (43.66) 1.4375-18 TABLE 2 - SHELL SIZE AN
14、D DIMENSIONS (FOR FIGURE 2) DASH NO. FITS CONNECTOR SHELL SIZE A DIAMETER MAXIMUM B MAXIMUMC MAXIMUM D DIAMETER .010 E .015 AS85049/26-2 RING, SHIELD CRIMP (REF) SEE REQUIREMENTS F MINIMUM SERIES II SERIES I 08 8 9 .75 (19.05) .54 (13.72) 1.14 (28.96) .337 (8,56) .250 (6.35) -8 .285 (7.24) 10 10 11
15、85 (21.59) .54 (13.72) 1.14 (28.96) .488 (12.40) .325 (8.26) -10 .475 (12.07)12 12 13 1.00 (25.40) .54 (13.72) 1.14 (28.96) .500 (12.70) .420 (10.67) -12 .475 (12.07)14 14 15 1.10 (27.94) .54 (13.72) 1.14 (28.96) .620 (15.75) .540 (13.72) -14 .475 (12.07)16 16 17 1.25 (31.75) .54 (13.72) 1.14 (28.9
16、6) .750 (19.05) .670 (17.02) -16 .475 (12.07)18 18 19 1.40 (35.56) .54 (13.72) 1.14 (28.96) .880 (22.35) .789 (20.04) -18 .475 (12.07)20 20 21 1.50 (38.10) .54 (13.72) 1.14 (28.96) 1.000 (25.40) .914 (23.22) -20 .475 (12.07)22 22 23 1.65 (41.91) .54 (13.72) 1.14 (28.96) 1.120 (28.45) 1.039 (26.39) -
17、22 .475 (12.07)24 24 25 1.75 (44.45) .54 (13.72) 1.14 (28.96) 1.192 (30.28) 1.112 (28.24) -24 .475 (12.07)TABLE 3 - MATERIAL AND FINISH FIGURE MATERIAL FINISH 1 COPPER ALLOY 3/ TIN-LEAD SOLDER PLATED 2 ALUMINUM ALLOY IN ACCORDANCE WITH AS85049 1/ N, 2/ W, X, 2/ Z 1/ NOT FOR NAVY USE, RESTRICTED TO A
18、IR FORCE SPACE APPLICATIONS ONLY. 2/ W AND Z FINISH NOT FOR USE IN SPACE APPLICATIONS. ALSO SEE SPECIFICATION NOTES. 3/ NOT FOR USE IN SPACE APPLICATIONS. ALSO SEE APPLICATION NOTE 1. AEROSPACE STANDARD AS85049/33 SHEET 4 OF 4 CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, NONENVIRONMENTAL, STRAIGHT,
19、 SHIELDED TERMINATION, THREADED APAPTER, CATEGORY 7 (FOR MIL-DTL-38999 SERIES I AND II CONNECTORS) REV. C PART NUMBER: SEE EXAMPLE BELOW: FOR FIGURE 1: SEE EXAMPLE BELOW: FOR FIGURE 2: SEE EXAMPLE BELOW: QUALIFICATION: FIGURE 1-SEE SAE AS85049, CATEGORY 7. ACCESSORIES TO BE SUBMITTED FOR QUALIFICATI
20、ON IN ASSEMBLED CONDITION. FIGURE 2-SEE SAE AS85049, CATEGORY 7. SUPERSESSION DATA: APPLICATION NOTES: 1. APPLICATION RESTRICTION: FIGURE 1 CONFIGURATION NOT FOR SPACE APPLICATIONS. AS85049 DOES NOT RESTRICT THE USE OF PURE TIN FINISHES WHICH MAY CAUSE TIN WHISKER GROWTH. FOR MORE INFORMATION ON TIN
21、 WHISKERS, SEE AIR5444. SPECIFICATION NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WH
22、ERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
