1、 AEROSPACE STANDARD INSULATION SLEEVING, ELECTRICAL, SHRINKABLE WITHOUT HEAT, CHLOROSULFONATED POLYETHYLENE FLEXIBLE AS85080/4Copyright 2012 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means,
2、 electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSU
3、ED 2004-04STABILIZED 2012-03 THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8D REV.A FEDERAL SUPPLY CLASS 5970 AS85080/4REV. A PROCUREMENT SPECIFICATION: MIL-I-85080SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. The
4、use ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized
5、 orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS85080/4A RATIONALE THIS DOCUMENT HAS BEEN DETERMINED TO CONTAIN BASIC AND STABLE TECHNOLOGY WHICH IS NOT DYNAMIC IN
6、NATURE. DESIGN AUTHORITIES MAY DETERMINE THAT THIS DOCUMENT IS NO LONGER TO BE USED FOR NEW DESIGN. THE PRODUCT IS NOT RECOMMENDED FOR AIRCRAFT APPLICATIONS (SEE AS50881). STABILIZED NOTICE THIS DOCUMENT HAS BEEN DECLARED “STABILIZED” BY THE AE-8D COMMITTEE AND WILL NO LONGER BE SUBJECTED TO PERIODI
7、C REVIEWS FOR CURRENCY. USERS ARE RESPONSIBLE FOR VERIFYING REFERENCES AND CONTINUED SUITABILITY OF TECHNICAL REQUIREMENTS. NEWER TECHNOLOGY MAY EXIST. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,
8、NOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-I-85080/4(AS), NOTICE 1 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS I
9、NTENDED TO REPLACE MIL-I-85080/4(AS), NOTICE 1. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING T
10、O ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORM
11、AT. UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS TECHNICAL REPORT. AEROSPACE
12、 STANDARD AS85080/4SHEET 1 OF 3 REV. A INSULATION SLEEVING, ELECTRICAL, SHRINKABLE WITHOUT HEAT, CHLOROSULFONATED POLYETHYLENE FLEXIBLE Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STAND
13、ARD AS85080/4SHEET 2 OF 3 REV. A INSULATION SLEEVING, ELECTRICAL, SHRINKABLE WITHOUT HEAT, CHLOROSULFONATED POLYETHYLENE FLEXIBLE REQUIREMENTS: CONTINUOUS OPERATING TEMPERATURE RANGE: -35C (-31F) TO +150C (+302F). MODE OF SHRINKAGE: THE HEATLESS SHRINK SLEEVING SHALL RECOVER TO A PREDETERMINED DIAME
14、TER UPON EXPOSURE TO THE ATMOSPHERE. NO EXTERNAL SOURCES OF HEAT ARE REQUIRED. COLOR: THE SLEEVING SHALL BE FURNISHED IN A BLACK COLOR THAT CONFORMS TO THE REQUIREMENTS OF CLASS II OF MIL-STD-104. OTHER COLORS ARE AVAILABLE. LONGITUDINAL CHANGE: 10 PERCENT. MILITARY PART NUMBER: THE MILITARY PART NU
15、MBER SHALL CONSIST OF THE BASIC NUMBER OF THIS SPECIFICATION SHEET AND DASH NUMBERS AS SHOWN BELOW: M85080/4 - X XX - X | | | | _ COLOR CODE DESIGNATOR (SEE 1.2.2) | | | | | | _ SIZE IDENTIFIER (TABLE I) | | | |_ CLASS (WHERE NO CLASSES ARE | SPECIFIED, THE NUMERIC “0“ | SHALL BE USED) | | _ SPECIFI
16、CATION SHEET EXAMPLE: BLACK, 0.672 INCH AS SUPPLIED I.D. SLEEVING SHALL BE IDENTIFIED AS M85080/4-005-0. TABLE I. DIMENSIONS (INCHES) 1/ AFTER UNRESTRICTED SHRINKAGE MILITARY PART NUMBER 2/ AS SUPPLIED I.D. MIN 3/ I.D. MAX WALL THICKNESS 4/ M85080/4-001-0 M85080/4-002-0 M85080/4-003-0 M85080/4-004-0
17、 M85080/4-005-0 M85080/4-006-0 M85080/4-007-0 M85080/4-008-0 M85080/4-009-0 M85080/4-010-0 M85080/4-011-0 M85080/4-012-0 M85080/4-013-0 .170 .252 .338 .506 .672 .843 1.012 1.181 1.350 1.688 2.025 2.363 2.700 .125 .187 .250 .375 .500 .625 .750 .875 1.000 1.250 1.500 1.750 2.000 .062 .062 .062 .062 .0
18、62 .062 .062 .062 .062 .062 .062 .062 .062 1/ DIAMETER LIMITS FOR OBJECT TO BE ENCLOSED SHOULD BE IN ACCORDANCE WITH THE RECOMMENDATIONS OF THE MANUFACTURER. 2/ THE COLOR CODE IDENTIFIED IS THE STANDARD ACQUISITION COLOR. 3/ THE INNER DIAMETER OF THE SLEEVE MAY BE MECHANICALLY EXPANDED 2X THE RECOVE
19、RED INSIDE DIAMETER WHEN IN THE AS-SUPPLIED CONDITION. THE MANUFACTURER SHOULD BE CONSULTED FOR SPECIAL APPLICATIONS AND RECOMMENDATIONS. 4/ WALL SHRINKAGE WILL BE LESS IF SHRINKAGE IS RESTRICTED. UNRESTRICTED SHRINKAGE: 4.6.3.13; 23 1C (73.4 2F) FOR 24 HOURS. Copyright SAE International Provided by
20、 IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS85080/4SHEET 3 OF 3REV. AINSULATION SLEEVING, ELECTRICAL, SHRINKABLE WITHOUT HEAT, CHLOROSULFONATED POLYETHYLENE FLEXIBLE TABLE II. PROPERTIES AFTER UNRESTRICTED SHRINKA
21、GE. PROPERTY REQUIREMENT TEST CONDITION RESTRICTED SHRINKAGE VOLTAGE WITHSTAND DIELECTRIC STRENGTH, VOLTS PER MIL MIN VOLUME RESISTIVITY, OHM-CM, MIN WATER ABSORPTION, % MAX FUNGUS RESISTANCE LOW TEMPERATURE FLEX HEAT SHOCK PROPERTIES AFTER HEAT RESISTANCE TEST: TENSILE STRENGTH, PSI, MIN ULTIMATE E
22、LONGATION, %, MIN CORROSION PROPERTIES AFTER FLUID RESISTANCE TEST: TENSILE STRENGTH, PSI, MIN ULTIMATE ELONGATION, %, MIN ODOR TENSILE STRESS, AT 200% ELONGATION, PSI, MAX TENSILE STRENGTH, PSI, MIN ULTIMATE ELONGATION, %, MIN FLAMMABILITY NO CRACKS PASS50010111.0NON NUTRIENT NO CRACKING NO CRACKS,
23、 FLOWING OR DRIPPING 600300NO CORROSION OR PITTING 1000400NO OBJECTION- ABLE ODOR 500500200SELF EXTINGUISHING; ONE MINUTE MAX. NO MORE THAN 25% OF IN- DICATOR FLAG BURNED. 4.6.3.24.6.64.6.2; ASTM D 876 4.6.2; ASTM D 876 4.6.2; ASTM D 570, PAR 6.1 4.6.2; ASTM G 21 4.6.6; -35 2C (-31 2F) 4.6.7; 150 1C
24、 (302 2F) 4.6.8; 100 1C (212 2F) FOR 96 HOURS. 4.6.94.6.104.6.114.6.2 ASTM D 412 4.6.13 ASTM D 638 SPEED D 4.6.13 ASTM D 638 SPEED D 4.6.14.1SHELF LIFE (AS SUPPLIED): TEST METHOD 4.6.16. MIL-I-85080/4(AS) IS INACTIVE FOR NEW DESIGN AND IS NO LONGER USED, EXCEPT FOR REPLACEMENT PURPOSES. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
