1、AEROSPACE STANDARD INFLATOR ASSEMBLY KIT AS85352/1Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the
2、prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2002-02REAFFIRMED 2007-12 STABILIZED 2013-10 THIRD ANGLE PROJECTION CUSTO
3、DIAN: A-5 REV.AFEDERAL SUPPLY CLASS 4920 AS85352/1REV. APROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitabi
4、lity forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values
5、 your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS85352/1ARATIONALE NEED TO OPEN A PROJECT TO PLACE ON A 28 DAY BALLOT FOR STABILIZATION. NEITHER A-5 NOR AGE-2C PLANS TO MAINTAIN THIS DOCUMENT. STABILIZED NOTICE THIS DOCUMENT HAS BEEN DECL
6、ARED “STABILIZED“ BY THE SAE A-5 AEROSPACE LANDING GEAR SYSTEMS COMMITTEE AND WILL NO LONGER BE SUBJECTED TO PERIODIC REVIEWS FOR CURRENCY. USERS ARE RESPONSIBLE FOR VERIFYING REFERENCES AND CONTINUED SUITABILITY OF TECHNICAL REQUIREMENTS. NEWER TECHNOLOGY MAY EXIST. Copyright SAE International Prov
7、ided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS85352/1 SHEET 1 OF 2 REV. A INFLATOR ASSEMBLY KIT NOTICETHIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-I-85352/1A AND CONTAINS ONLY MI
8、NOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-I-85352/1A. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED.THE ORIGINAL MIL
9、ITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNM
10、ENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY
11、FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,
12、AEROSPACE STANDARD AS85352/1 SHEET 2 OF 2 REV. A INFLATOR ASSEMBLY KIT THIS SPECIFICATION IS APPROVED FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE.THE REQUIREMENTS FOR ACQUIRING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE ISSUE OF THE FOL
13、LOWING SPECIFICATION LISTED IN THAT ISSUE OF THE DEPARTMENT OF DEFENSE INDEX OF SPECIFICATIONS AND STANDARDS (DODISS) SPECIFIED IN THE SOLICITATION: MIL-I-85352.FIGURE 1. INFLATOR ASSEMBLY KITREQUIREMENTS:INFLATOR ASSEMBLY KIT: THE INFLATOR ASSEMBLY KIT SHALL CONSIST OF THE INFLATOR ASSEMBLY SHOWN W
14、ITH BOTH SIZE 1 AND SIZE 2 GAGE ELEMENTS, THE SERVICE HOSE/TIRE VALVE ADAPTER ASSEMBLY, AND THE INFLATOR ASSEMBLY CARRYING CASE.PART NUMBER: PART NUMBERS SHALL CONSIST OF THE FOLLOWING:(IN SEQUENCE)1. THE LETTER “M”2. THE GENERAL SPECIFICATION NUMBER3. A SLASH, AND SLASH NUMBER OF THIS SPECIFICATION SHEETEXAMPLE:M85352/1Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
