1、 AEROSPACE STANDARD CABLE, ELECTRIC, FILTER LINE, COMPONENT WIRE, TIN-COATED COPPER CONDUCTOR, RADIO FREQUENCY, ABSORPTIVE, 150C, 600-VOLT AS85485/9 Copyright 2004 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in an
2、y form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: custsvcsae.org SAE WEB ADDRESS: http:/www.
3、sae.org ISSUED 2004-06THIRD ANGLE PROJECTION CUSTODIAN: SAE AE-8/AE-8D FEDERAL SUPPLY CLASS6145 AS85485/9SHEET 1 OF 4 PROCUREMENT SPECIFICATION: MIL-C-85485SAE TechnicalStandards Board Rules provide that: “This report is published by SAE toadvance thestate of technical andengineering sciences. Theus
4、e of thisreport is entirely voluntary, andits applicabilityandsuitability forany particularuse,including any patent infringement arising therefrom, is thesole responsibility oftheuser.” SAE reviews each technical report at least every five yearsat which time it may be reaffirmed, revised, orcancelle
5、d.SAE invites yourwritten commentsandsuggestions. NOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-C-85485/9A AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE I
6、NITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-C-85485/9A. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS
7、 (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFI
8、CATION OR STANDARD FORMAT. UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS TECH
9、NICAL REPORT. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD CABLE, ELECTRIC, FILTER LINE, COMPONENT WIRE, TIN-COATED COPPER CONDUCTOR, RADIO FREQUENCY, ABSORPTIVE, 150C, 600-VOLT
10、 AS85485/9 AS85485/9SHEET 2 OF 4 FIGURE 1. GENERAL CONFIGURATION TABLE I. CONSTRUCTION DETAILS TABLE II. PERFORMANCE DETAILS Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD CABLE,
11、ELECTRIC, FILTER LINE, COMPONENT WIRE, TIN-COATED COPPER CONDUCTOR, RADIO FREQUENCY, ABSORPTIVE, 150C, 600-VOLT AS85485/9 AS85485/9SHEET 3 OF 4 RATINGS: TEMPERATURE RATING: 150C (302F) MAX CONTINUOUS CONDUCTOR TEMPERATURE. VOLTAGE RATING: 600 VOLTS (RMS) AT SEA LEVEL. ADDITIONAL REQUIREMENTS: ATTENU
12、ATION (INSERTION LOSS): THE WIRE OF THIS SPECIFICATION SHEET, WHEN SHIELDED IN ACCORDANCE WITH M85485/12-*T1*, SHALL MEET THE ATTENUATION REQUIREMENTS OF TABLE III AS SPECIFIED FOR THE APPLICABLE SIZE OF WIRE. BLOCKING: 200 3C (392 5F) FOR 6 HOURS COLOR: PRIMARY INSULATION - NATURAL FILTER LAYER - B
13、LACK PRIMARY JACKET - LIGHT VIOLET COLOR STRIPING DURABILITY: 125 CYCLES (250 STROKES) (MIN), 500 GRAMS WEIGHT. CONCENTRICITY: PRIMARY INSULATION - 50% (MIN); FINISHED WIRE - 70% (MIN). CROSSLINKING PROOF TEST: 7 HOURS AT 300 3C (572 5F). FLAMMABILITY: 3 SECONDS (MAX); 3 INCHES (MAX). HUMIDITY RESIS
14、TANCE: INSULATION RESISTANCE, 5000 MEGOHMS FOR 1000 FEET (MIN). IDENTIFICATION DURABILITY: 125 CYCLES (250 STROKES) (MIN), 500 GRAMS WEIGHT. IMMERSION: DIAMETER INCREASE 5% (MAX); NO CRACKING, NO DIELECTRIC BREAKDOWN. INSULATION ELONGATION AND TENSILE STRENGTH: PRIMARY INSULATION, FILTER LAYER AND P
15、RIMARY JACKET PULLED TOGETHER. ELONGATION, 50% (MIN) TENSILE STRENGTH, 3000 LBF/IN2(MIN) INSULATION FLAWS: PRIMARY INSULATION ONLY SPARK TEST; 1.5 KILOVOLTS (RMS), 60 HZ IMPULSE DIELECTRIC TEST; 6.0 KILOVOLTS (PEAK) FINISHED WIRE SPARK TEST; 3.0 KILOVOLTS (RMS), 60 HZ IMPULSE DIELECTRIC TEST; 8.0 KI
16、LOVOLTS (PEAK) INSULATION RESISTANCE: 5000 MEGOHMS FOR 1000 FEET (MIN) INSULATION THICKNESS: PRIMARY INSULATION 0.002 INCH (MIN) FILTER LAYER; AVERAGE 0.0025 INCH (MIN) PRIMARY JACKET; 0.0035 INCH (MIN) LIFE CYCLE: 168 HOURS AT 200 3C (392 5F) LOW TEMPERATURE-COLD BEND: -65 2C (-85 4F) FOR 4 HOURS S
17、HRINKAGE: 0.125 INCH (MAX) AT 200 3C (392 5F) SMOKE: 200 2C (392 4F); NO VISIBLE SMOKE. SURFACE RESISTANCE: 500 MEGOHM-INCHES (MIN), INITIAL AND FINAL READINGS. THERMAL SHOCK RESISTANCE: OVEN TEMPERATURE, 150 3C (302 5F) MAX. CHANGE IN MEASUREMENT, 0.060 INCH THERMAL STABILITY: 1250 HOURS AT 180 3C
18、(356 5F). THE WIRE OF THIS SPECIFICATION SHEET, WHEN SHIELDED IN ACCORDANCE WITH M85485/12-*T1*, SHALL MEET THE VOLTAGE WITHSTAND (DIELECTRIC) OF 1500 VOLTS (RMS), 60 HZ, AND THE STOP BAND ATTENUATION REQUIREMENTS FOR THE APPLICABLE SIZE OF WIRE AS SPECIFIED IN TABLE III. Copyright SAE International
19、 Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD CABLE, ELECTRIC, FILTER LINE, COMPONENT WIRE, TIN-COATED COPPER CONDUCTOR, RADIO FREQUENCY, ABSORPTIVE, 150C, 600-VOLT AS85485/9 AS85485/9SHEET 4 OF 4 VOLTAGE
20、WITHSTAND (POST-ENVIRONMENTAL): 1500 VOLTS (RMS), 60 HZ WRAP TEST: 6 HOURS AT 200 3C (392 5F); NO CRACKING. TABLE III. ATTENUATION (INSERTION LOSS) FIGURE 2. ATTENUATION (INSERTION LOSS) ENGINEERING REFERENCE CURVE APPLICATION NOTE: COMPONENT WIRE IS AN EFFECTIVE RADIO FREQUENCY ABSORPTIVE WIRE ONLY
21、 WHEN USED AS A COMPONENT IN A SHIELDED CABLE. QUALIFYING ACTIVITY: THE ACTIVITY RESPONSIBLE FOR THIS QUALIFIED PRODUCTS LIST IS THE NAVAL AIR SYSTEMS COMMAND, WASHINGTON, D.C. 20361. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
