1、AEROSPACE STANDARD BEARING, FIBER REINFORCED PLASTIC, SLEEVE, FLANGED, SELF-LUBRICATING, +250 F AS85560/2Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanic
2、al, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2004-11REVISED 201
3、3-01THIRD ANGLE PROJECTION CUSTODIAN: AIRFRAME CONTROL BEARINGS GROUP REV.BFEDERAL SUPPLY CLASS 3120 REV. BPROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is e
4、ntirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwri
5、ttencomments andsuggestions. AS85560/2SHEET 1 OF 3SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS85560/2BRATIONALE AS85560/2B WAS CREATED IN ASSOCIATION WITH THE FIVE YEAR DOCUMENT REVIEW TO UPDATE NUMBER FORMATTING IN ACCORDA
6、NCE WITH THE SAE TECHNICAL REPORT STYLE MANUAL. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF: SAE AS85560. NOTE FOR DETAIL A: OPTIONAL LINER TRIMMING METHOD: CHAMFERED EDGES PERMITTED. FIGURE 1 AEROSPACE STANDARD A
7、S85560/2SHEET 2 OF 3REV. BBEARING, FIBER REINFORCED PLASTIC, SLEEVE, FLANGED, SELF-LUBRICATING, +250 F TABLE 1 - DIMENSIONS PART NO.-XX NOMINAL BORE SIZE B DIA. +.0000 .0010 D DIA. +.0005 .0005 F+.000 .005 H DIA. +.000 .020 M85560/204 1/4 .2515 .3760 .0625 .750 M85560/205 5/16 .3140 .4386 .0625 .812
8、 M85560/206 3/8 .3765 .5012 .0625 .875 M85560/207 7/16 .4390 .5638 .0625 .937 M85560/208 1/2 .5015 .6265 .0625 1.000 M85560/209 9/16 .5640 .6892 .0625 1.125 M85560/210 5/8 .6265 .8142 .0625 1.250 M85560/211 11/16 .6890 .8767 .0625 1.375 M85560/212 3/4 .7515 .9393 .0625 1.500 M85560/214 7/8 .8765 1.0
9、645 .0625 1.625 M85560/216 1 1.0015 1.1898 .0625 1.750 M85560/218 1-1/8 1.1265 1.3148 .0937 1.875 M85560/220 1-1/4 1.2515 1.4398 .0937 2.000 M85560/222 1-3/8 1.3765 1.5648 .0937 2.125 M85560/224 1-1/2 1.5015 1.7523 .0937 2.250 M85560/226 1-5/8 1.6265 1.8773 .0937 2.375 M85560/228 1-3/4 1.7515 2.0023
10、 .0937 2.500 M85560/232 2 2.0015 2.2523 .0937 2.750 MATERIAL: COMPOSITE: GLASS OR ARAMID FIBERS IN RESIN MATRIX. SELF-LUBRICATING SURFACE: TETRAFLUOROETHYLENE PER AS85560. SURFACE TEXTURE: UNLESS OTHERWISE SPECIFIED, SMOOTH MACHINE FINISH 125 MICROINCH Ra MAXIMUM ON OD, 250 MICROINCH Ra MAXIMUM ON A
11、LL OTHER SURFACES IN ACCORDANCE WITH ASME B46.1. SURFACE TEXTURE OF SELF-LUBRICATING SURFACE IS NOT SPECIFIED. TEMPERATURE RANGE: 65 TO +250 F. BREAK SHARP EDGES AND CORNERS AND REMOVE ALL BURRS AND SLIVERS. UNLESS OTHERWISE SPECIFIED, DIMENSIONS IN INCHES. MARKING: FOR DASH NO. 08 AND LARGER, THE P
12、ART NUMBER FROM TABLE 1 SHALL BE MARKED ON THE PART. SMALLER SIZES SHOULD BE IDENTIFIED WITH A TAG OR ON THE BAG. NOTES: 1. EXAMPLE OF PART NUMBER: M85560/2 -04 -008 = .250 IN BORE DIAMETER BY .250 IN LONG LENGTH CODE IN ACCORDANCE WITH TABLE 2 (USE ONLY ASSIGNED LENGTH CODES SHOWN IN TABLE 2) BORE
13、DIAMETER CODE IN ACCORDANCE WITH TABLE 1 (USE ONLY ASSIGNED BORE CODES SHOWN IN TABLE 1) BASIC PART NUMBER AEROSPACE STANDARD AS85560/2SHEET 3 OF 3REV. BBEARING, FIBER REINFORCED PLASTIC, SLEEVE, FLANGED, SELF-LUBRICATING, +250 F 2. IN THE EVENT OF A CONFLICT BETWEEN THE TEXT OF THIS STANDARD AND TH
14、E REFERENCED CITED HEREIN, THE TEXT OF THIS STANDARD SHALL TAKE PRECEDENCE. 3. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON THE DATE OF INVITATION FOR BID AND FORM A PART OF THIS STANDARD TO THE EXTENT SPECIFIED HEREIN. 4. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE
15、 OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN OR
16、IGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. LOAD RATINGS: RADIAL STATIC LIMIT LOAD = 50 000 x B x (L + F .13) POUND DYNAMIC RADIAL LOAD = 25 000 x B x (L + F .13) POUND TABLE 2 - LENGTH CODES PART NO. NOMINAL SIZE LENGTH L + .000/ -.010 1/4 9/32 5/16 11/32 3/8 7/16 1/2
17、 9/16 5/8 11/16 3/4 7/8 M85560/2-04 1/4 008 009 010 011 012 014 M85560/2-05 5/16 008 009 010 011 012 014 016 018 M85560/2-06 3/8 008 009 010 011 012 014 016 018 020 022 M85560/2-07 5/16 008 009 010 011 012 014 016 018 020 022 024 028 M85560/2-08 1/2 008 009 010 011 012 014 016 018 020 022 024 028 M8
18、5560/2-09 7/16 008 009 010 011 012 014 016 018 020 022 024 028 M85560/2-10 5/8 008 009 010 011 012 014 016 018 020 022 024 028 M85560/2-11 11/16 008 009 010 011 012 014 016 018 020 022 024 028 M85560/2-12 3/4 008 009 010 011 012 014 016 018 020 022 024 028 M85560/2-14 7/8 008 009 010 011 012 014 016
19、 018 020 022 024 028 M85560/2-16 1 008 009 010 011 012 014 016 018 020 022 024 028 M85560/2-18 1 1/8 010 011 012 014 016 018 020 022 024 028 M85560/2-20 1 1/4 012 014 016 018 020 022 024 028 M85560/2-22 1 3/8 012 014 016 018 020 022 024 028 M85560/2-24 1 1/2 012 014 016 018 020 022 024 028 M85560/2-
20、26 1 5/8 016 018 020 022 024 028 M85560/2-28 1 3/4 016 018 020 022 024 028 M85560/2-32 2 016 018 020 022 024 028 PART NO. NORMAL SIZE LENGTH L + .000/ -.010 1 1 1/8 1 1/4 1 3/8 1 1/2 1 5/8 1 3/4 1 7/8 2 2 1/8 2 1/4 2 3/8 2 1/2 2 3/4 3 M8560/2-04 1/4 M8560/2-05 5/16 M8560/2-06 3/8 M8560/2-07 3/16 M85
21、60/2-08 1/2 M85560/2-09 9/16 032 036 M85560/2-10 5/8 032 036 040 044 M85560/2-11 11/16 032 036 040 044 048 052 M85560/2-12 3/4 032 036 040 044 048 052 M85560/2-14 7/8 032 036 040 044 048 052 M85560/2-16 1 032 036 040 044 048 052 056 060 M85560/2-18 1 1/8 032 036 040 044 048 052 056 060 M85560/2-20 1
22、 1/4 032 036 040 044 048 052 056 060 064 068 M85560/2-22 1 3/8 032 036 040 044 048 052 056 060 064 068 M85560/2-24 1 1/2 032 036 040 044 048 052 056 060 064 068 072 076 080 088 M85560/2-26 1 5/8 032 036 040 044 048 052 056 060 064 068 072 076 080 088 096M85560/2-28 1 3/4 032 036 040 044 048 052 056 060 064 068 072 076 080 088 096M85560/2-32 2 032 036 040 044 048 052 056 060 064 068 072 076 080 088 096
