1、 AEROSPACE STANDARD BOLT, MACHINE - HEXAGON HEAD, DRILLED 1 HOLE, PD SHANK, BLACK OXIDE, STEEL UNS G87400, 125 KSI MIN, .3750-24 UNJF-3A AS9297Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form
2、 or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:
3、/www.sae.org ISSUED 1999-12REAFFIRMED2004-07REVISED 2015-07THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.B FEDERAL SUPPLY CLASS 5306AS9297 SHEET 1 OF 3 REV. B PROCUREMENT SPECIFICATION: AS7452 /3/SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of tec
4、hnicalandengineering sciences. Theuse ofthisreport is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay be
5、revised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS9297B RATIONALE ADD TO STRAIGHTNESS FEATURE CONTROL FRAME, ADD MARKING EDGE DISTANCE N
6、OTE, UPDATE POSITION FEATURE CONTROL FRAME, UPDATE DRAWING NOTE 4, AND GENERAL EDITORIAL UPDATE. NOTICE THE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9297, NOTICE 1. THIS SAE STANDARD RETAINS THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY D
7、OCUMENT. ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE 1 - BOLT AEROSPACE STANDARD AS9297 SHEET 2 OF 3 REV.
8、 B BOLT, MACHINE - HEXAGON HEAD, DRILLED 1 HOLE, PD SHANK, BLACK OXIDE, STEEL UNS G87400, 125 KSI MIN, .3750-24 UNJF-3A TABLE 1 - PART NUMBERS AND DIMENSIONS PART NUMBER L K APPROX. MASS LB/100 PART NUMBER L K APPROX. MASS LB/100 MS9297-04 .615- .635 .088- .108 3.33 MS9297-31 2.865-2.885 1.815-1.875
9、 9.39 MS9297-05 .678- .698 .088- .108 3.50 MS9297-32 2.990-3.010 1.940-2.000 9.72 MS9297-06 .740- .760 .088- .108 3.67 MS9297-33 3.115-3.135 2.065-2.125 10.06 MS9297-07 .802- .822 .088- .108 3.84 MS9297-34 3.240-3.260 2.190-2.250 10.39 MS9297-08 .865- .885 .088- .108 4.01 MS9297-35 3.365-3.385 2.315
10、2.375 10.73 MS9297-09 .928- .948 .088- .108 4.18 MS9297-36 3.490-3.510 2.440-2.500 11.07 MS9297-10 .990-1.010 .088- .108 4.35 MS9297-37 3.615-3.635 2.565-2.625 11.40 MS9297-11 1.052-1.072 .088- .108 4.51 MS9297-38 3.740-3.760 2.690-2.750 11.74 MS9297-12 1.115-1.135 .088- .125 4.68 MS9297-39 3.865-3
11、885 2.815-2.875 12.07 MS9297-13 1.178-1.198 .128- .188 4.85 MS9297-40 3.990-4.010 2.940-3.000 12.41 MS9297-14 1.240-1.260 .190- .250 5.02 MS9297-41 4.115-4.135 3.065-3.125 12.75 MS9297-15 1.302-1.322 .252- .312 5.19 MS9297-42 4.240-4.260 3.190-3.250 13.08 MS9297-16 1.365-1.385 .315- .375 5.35 MS929
12、7-43 4.365-4.385 3.315-3.375 13.42 MS9297-17 1.428-1.448 .378- .438 5.52 MS9297-44 4.490-4.510 3.440-3.500 13.75 MS9297-18 1.490-1.510 .440- .500 5.69 MS9297-45 4.615-4.635 3.565-3.625 14.09 MS9297-19 1.552-1.572 .502- .562 5.86 MS9297-46 4.740-4.760 3.690-3.750 14.43 MS9297-20 1.615-1.635 .565- .62
13、5 6.03 MS9297-47 4.865-4.885 3.815-3.875 14.75 MS9297-21 1.678-1.698 .628- .688 6.19 MS9297-48 4.990-5.010 3.940-4.000 15.10 MS9297-22 1.740-1.760 .690- .750 6.36 MS9297-49 5.115-5.135 4.065-4.125 15.43 MS9297-23 1.865-1.885 .815- .875 6.70 MS9297-50 5.240-5.260 4.190-4.250 15.77 MS9297-24 1.990-2.0
14、10 .940-1.000 7.03 MS9297-51 5.365-5.385 4.315-4.375 16.11 MS9297-25 2.115-2.135 1.065-1.125 7.37 MS9297-52 5.490-5.510 4.440-4.500 16.44 MS9297-26 2.240-2.260 1.190-1.250 7.71 MS9297-53 5.615-5.635 4.565-4.625 16.78 MS9297-27 2.365-2.385 1.315-1.375 8.04 MS9297-54 5.740-5.760 4.690-4.750 17.11 MS92
15、97-28 2.490-2.510 1.440-1.500 8.38 MS9297-55 5.865-5.885 4.815-4.875 17.45 MS9297-29 2.615-2.635 1.565-1.625 8.71 MS9297-56 5.990-6.010 4.940-5.000 17.79 MS9297-30 2.740-2.760 1.690-1.750 9.05 NOTES: /1/ FOR PARTS NUMBERS MS9297-04 THRU MS9297-21 DATUM Z SHALL REPLACE DATUM Y. 2. MATERIAL: STEEL PER
16、 AMS6322 (UNS G87400). /3/ PROCUREMENT SPECIFICATION: AS7452, EXCEPT HEAD SHALL BE UPSET. 4. HEAD TO SHANK FILLET SHALL BE COLD ROLLED AFTER HEAT TREATMENT. COLD ROLLING SHALL BE SUFFICIENT TO REMOVE ALL VISUAL EVIDENCE OF GRINDING OR TOOL MARKS. 5. FINISH: BLACK OXIDE TREATMENT PER AMS2485. 6. MAGN
17、ETIC PARTICLE INSPECTION PER ASTM E1444/E1444M. 7. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 8. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 9. DIMENSIONS ARE IN INCHES. AEROSPACE STANDARD AS9
18、297 SHEET 3 OF 3 REV. B BOLT, MACHINE - HEXAGON HEAD, DRILLED 1 HOLE, PD SHANK, BLACK OXIDE, STEEL UNS G87400, 125 KSI MIN, .3750-24 UNJF-3A 10. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 11. DO NOT USE UNASSIGNED PART NUMBERS. 12. A CHANGE BAR (l) LOCATED IN THE LEFT MARG
19、IN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.
