1、AEROSPACE STANDARD NUT, PLAIN, HEXAGON - DRILLED, SILVER PLATED - UNS S66286, 130 KSI MIN AS9360Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photo
2、copying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1999-12REAFFIRMED 2007-06 R
3、EVISED 2013-07THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.CFEDERAL SUPPLY CLASS 5310 AS9360SHEET 1 OF 3REV. CSAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits appl
4、icability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsu
5、ggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS9360CRATIONALE REVISE THREAD SPECIFICATION TO AS8879, UPDATE FPI REQUIREMENTS, UPDATE POSITIONAL TOLERANCE ON DRILLED HOLES, FIGURE 1 REDRAWN AND EDITORIAL UPDATE. NOTI
6、CE THE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9360B, NOTICE 1. THIS SAE STANDARD MAY RETAIN THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDA
7、TORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE 1 NUT AEROSPACE STANDARD AS9360SHEET 2 OF 3REV. CNUT, PLAIN, HEXAGON - DRILLED, SILVER PLATED - UNS S66286, 130 KSI MIN TABLE 1A PART NUMBERS AND DIM
8、ENSIONS D, AF, E, F, AB, K, AND L PARTNUMBER DTHREAD AF EMINFMIN AB K LMINMS9360-04 .1120-48 UNJF-3B .243- .251 .268 .240 .112- .132 .126-.146 .240 MS9360-06 .1380-40 UNJF-3B .305- .313 .339 .302 .138- .158 .126-.146 .302 MS9360-08 .1640-36 UNJF-3B .336- .345 .375 .334 .164- .194 .126-.146 .334 MS93
9、60-09 .1900-32 UNJF-3B .367- .376 .410 .365 .190- .220 .146-.166 .365 MS9360-10 .2500-28 UNJF-3B .429- .439 .481 .428 .250- .280 .209-.229 .428 MS9360-11 .3125-24 UNJF-3B .492- .502 .552 .490 .312- .342 .256-.276 .490 MS9360-12 .3750-24 UNJF-3B .553- .564 .623 .552 .375- .405 .318-.338 .552 MS9360-1
10、3 .4375-20 UNJF-3B .679- .690 .765 .678 .438- .468 .365-.385 .678 MS9360-14 .5000-20 UNJF-3B .741- .752 .836 .740 .500- .535 .428-.448 .740 MS9360-15 .5625-18 UNJF-3B .865- .877 .978 .865 .562- .597 .474-.494 .865 MS9360-16 .6250-18 UNJF-3B .928- .940 1.049 .928 .625- .660 .537-.557 .928 MS9360-17 .
11、7500-16 UNJF-3B 1.052-1.064 1.192 1.052 .750- .785 .646-.666 1.052 MS9360-18 .8750-14 UNJF-3B 1.239-1.252 1.405 1.239 .875- .910 .756-.776 1.240 MS9360-19 1.0000-12 UNJF-3B 1.427-1.440 1.619 1.427 1.000-1.035 .865-.885 1.428 TABLE 1B PART NUMBERS AND DIMENSIONS J, P, T, AK, AND APPROX. MASS PARTNUMB
12、ER J P T AK APPROX. MASSLB/100 MS9360-04 .027-.035 .068 .090 .005 .17 MS9360-06 .043-.051 .068 .115 .005 .27 MS9360-08 .043-.051 .068 .135 .005 .32 MS9360-09 .043-.051 .078 .150 .005 .37 MS9360-10 .043-.051 .110 .185 .005 .75 MS9360-11 .043-.051 .133 .215 .005 1.11 MS9360-12 .043-.051 .164 .245 .010
13、 1.63 MS9360-13 .066-.074 .187 .300 .010 2.93 MS9360-14 .066-.074 .219 .335 .010 3.84 MS9360-15 .066-.074 .362 .385 .010 6.04 MS9360-16 .066-.074 .400 .420 .010 7.50 MS9360-17 .066-.074 .485 .490 .010 10.69 MS9360-18 .066-.074 .570 .555 .010 17.50 MS9360-19 .066-.074 .655 .655 .010 26.78 NOTES: 1. M
14、ATERIAL: CORROSION AND HEAT RESISTANT STEEL AMS5732 OR AMS5737 (UNS S66286). 2. SURFACE FINISH: SILVER PLATE PER AMS2410. .0002 TO .0006 THICK ON THREAD AT PD. DIMENSIONS ARE AFTER PLATING. 3. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACE
15、S TO BE 125 MICROINCHES Ra. 4. FLUORESCENT PENETRANT INSPECTION BEFORE PLATING PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MIN AND AS5447. 5. BREAK EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 6. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). AEROSPACE STANDARD AS936
16、0SHEET 3 OF 3REV. CNUT, PLAIN, HEXAGON - DRILLED, SILVER PLATED - UNS S66286, 130 KSI MIN /7/ MARKING: MARK MATERIAL CODE “EH19“ PER AS269 ON -04 THRU -08 AND THE COMPLETE PART NUMBER ON -09 AND LARGER AND MANUFACTURERS IDENTIFICATION IN ACCORDANCE WITH AS478, CLASS C. MULTIPLE MARKING OF BAR STOCK
17、PERMISSIBLE PROVIDED POSITIVE IDENTIFICATION IS SHOWN. DASH NUMBERS MAY APPEAR ON ADJACENT FLATS. PARTS SHALL BE MARKED BEFORE THREADING. 8. DIMENSIONS ARE IN INCHES. 9. DO NOT USE UNASSIGNED PART NUMBERS. 10. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING
18、 AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.
