1、AEROSPACE STANDARDBOLT, MACHINE HEXAGON HEAD, DRILLED,1 HOLE, FULL SHANK, CRES, UNS S66286,130 KSI MIN, .5000-20 UNJF-3AAS9505Copyright 2016 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means,
2、electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUED19
3、99-04 REAFFIRMED2007-06 REVISED2016-08THIRD ANGLE PROJECTIONCUSTODIAN: E-25REV.BFEDERAL SUPPLY CLASS5306AS9505SHEET 1 OF 3REV.BPROCUREMENT SPECIFICATION: NONESAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengineering sciences. The use of thisr
4、eport isentirelyvoluntary, andits applicability andsuitability for any particularuse, includingany patent infringement arising therefrom,is the soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,stabilized,orcancelled.SAEinvites yo
5、urwritten comments andsuggestions.SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS9505BRATIONALEFIGURE REDRAWN TO CORRECT THREAD SPEC, TABLE REDRAWN FOR CLARITY, NOTE ADDED FOR USE OFSTOCK, D NOTE ADDED FOR ANGULAR TOLERANCE, A
6、ND GENERAL UDATE.NOTICETHE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARDMS9505A, AMENDMENT 1. THIS SAE STANDARD MAY RETAIN THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT.ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPLS) MA
7、Y CONTINUE TO BEMANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT.MARK PART NUMBER ANDMANUFACTURERS IDENTIFICATIONPER AS 478 CLASS A.023 Y.836 MIN.741.752.006.026KL.003 Y.271.291THREADRUNOUT PER AS3062.
8、0303232250.5000 - 20 UNJF - 3A.499.495.006 ZABEARING SURFACEZYSECTION THRUTHREAD PROFILE32 .002 / 1TO .740 -.760 .760 MAX .710 MINSHAPE IN THISAREA OPTIONALARRANGEMENT OPTIONALVIEW AR.020CHAMFER.037- .057 X 45 APPROX PER AS88792502502535 .060 - .070 .090 - .110 85 - 95/1/.191.211BOTH ENDS.023 YFIGUR
9、E 1 BOLTAEROSPACE STANDARDAS9505SHEET 2 OF 3REV.BBOLT, MACHINE HEXAGON HEAD, DRILLED,1 HOLE, FULL SHANK, CRES, UNS S66286,130 KSI MIN, .5000-20 UNJF-3ATABLE 1 PART NUMBERS AND DIMENSIONSPART NO. L KAPPROX.MASSLB/100 PART NO. L KAPPROX.MASSLB/100MS9505-04MS9505-05MS9505-06.802- .822.865- .885.928- .9
10、48.105- .125.105- .125.105- .1258.308.659.00MS9505-31MS9505-32MS9505-333.240- 3.2603.365- 3.3853.490- 3.5101.940- 2.0002.065- 2.1252.190- 2.25021.8322.5223.22MS9505-07MS9505-08MS9505-09.990- 1.0101.052- 1.0721.115- 1.135.105- .125.105- .125.105- .1259.359.7210.04MS9505-34MS9505-35MS9505-363.615- 3.6
11、353.740- 3.7603.865- 3.8852.315- 2.3752.440- 2.5002.565- 2.62523.9124.6025.30MS9505-10MS9505-11MS9505-121.178- 1.1981.240- 1.2601.302- 1.322.105- .125.105- .125.105- .12510.3910.7311.08MS9505-37MS9505-38MS9505-393.990- 4.0104.115- 4.1354.240- 4.2602.690- 2.7502.815- 2.8752.940- 3.00025.9926.6827.38M
12、S9505-13MS9505-14MS9505-151.365- 1.3851.428- 1.4481.490- 1.510.105- .125.128- .188.190- .25011.4311.7812.12MS9505-40MS9505-41MS9505-424.365- 4.3854.490- 4.5104.615- 4.6353.065- 3.1253.190- 3.2503.315- 3.37528.0828.7729.46MS9505-16MS9505-17MS9505-181.552- 1.5721.615- 1.6351.678- 1.698.252- .312.315-
13、375.378- .43812.4812.8713.16MS9505-43MS9505-44MS9505-454.740- 4.7604.865- 4.8854.990- 5.0103.440- 3.5003.565 - 3.6253.690- 3.75030.1530.8431.54MS9505-19MS9505-20MS9505-211.740- 1.7601.865- 1.8851.990- 2010.440- .500.565- .625.690- .75013.5114.2014.89MS9505-46MS9505-47MS9505-485.115 5.1355.240- 5.26
14、05.365- 5.3853.815- 3.8753.940- 4.0004.065- 4.12532.2332.5233.62MS9505-22MS9505-23MS9505-242.115- 2.2352.240- 2.2602.365- 2.385.815- .875.940-1.0001.065-1.12515.5916.2816.97MS9505-49MS9505-50MS9505-515.490- 5.5105.615- 5.6355.740- 5.7604.190- 4.2504.315- 4.3754.440- 4.50034.3135.0135.70MS9505-25MS95
15、05-26MS9505-272.490- 2.5102.615- 2.6352.740- 2.7601.190-1.2501.315-1.3751.440-1.50017.6718.3619.05MS9505-52MS9505-53MS9505-545.865- 5.8855.990- 6.0101.802- 1.8224.565- 4.6254.690- 4.750.502- .56236.3937.0913.85MS9505-28MS9505-29MS9505-302.865- 2.8852.990- 3.0103.115- 3.1351.565-1.6251.690-1.7501.815
16、1.87519.7520.4421.14MS9505-55 1.928- 1.948 .628- .688 14.55NOTES:1. FOR PART NUMBERS MS9505-04 THROUGH MS9505-24 THE THREAD PD (DATUM -Z- ) SHALL REPLACE DATUM -Y- .2. MATERIAL: CORROSION AND HEAT RESISTANT STEEL AMS5731 (UNS S66286).3. PROCUREMENT SPECIFICATION: AS7477.4. FLUORESCENT PENETRANT INS
17、PECTION PER ASTM 1417/E14717M.5. INCOMPLETE THREADS NOT TO ENTER FILLET.6. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra.7. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED.8. DIMENSIONING AND TOLERANCI
18、NG PER ANSI Y14.5M-1982 (ASME PUBLICATION).9. UOS ANGULAR DIMENSIONS 5 DEGREES.10. DIMENSIONS IN INCHES.11. DO NOT USE UNASSIGNED PART NUMBERS.12. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWING OR SPECIFICATIONS MAY BE PROCURED AND USED UNTIL
19、STOCK IS DEPLETED. AEROSPACE STANDARDAS9505SHEET 3 OF 3REV.BBOLT, MACHINE HEXAGON HEAD, DRILLED,1 HOLE, FULL SHANK, CRES, UNS S66286,130 KSI MIN, .5000-20 UNJF-3A13. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL R
20、EVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS.ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION.ASTM IS AN ASTM INTERNATIONAL PUBLICATION.
