1、AEROSPACE STANDARDSCREW, MACHINE STEEL UNS G87400,CADMIUM PLATE, DRILLED, 1 HOLEHEXAGON HEAD, .1640-36 UNJF-3AAS9528Copyright 2016 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic
2、 mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUED2000-08 REAF
3、FIRMED2004-07 REVISED2016-06THIRD ANGLE PROJECTIONCUSTODIAN: E-25REV.BFEDERAL SUPPLY CLASS5305AS9528SHEET 1 OF 2REV.BPROCUREMENT SPECIFICATION: AS7452, SEE NOTE /3/SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengineering sciences. The use of
4、 thisreport isentirelyvoluntary, andits applicability andsuitability for any particularuse, includingany patent infringement arising therefrom,isthe soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,stabilized,orcancelled.SAEinvit
5、es yourwritten comments andsuggestions.SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS9528BRATIONALEADD DIAMETER SYMBOL TO FEATURE CONTROL FRAME FOR STRAIGHTNESS CALLOUT, UPDATE ANSI Y14.5M SYMBOLS AND FORMATTING, RELOCATE W D
6、ATUM AND ADD A TERTIARY DATUM FOR DRILLED HOLE POSITION, ADD NOTE FOR USAGE OF EXISTING INVENTORY, ADD EDGE DISTANCE EXCEPTION FOR HEAD MARKING,FIGURE 1 REDRAWN, GENERAL EDITORIAL UPDATE.NOTICETHE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9528. THIS SA
7、E STANDARD RETAINS THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT.ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF
8、THIS SAE DOCUMENT.FIGURE 1 - SCREWAEROSPACE STANDARDAS9528SHEET 2 OF 2REV.BSCREW, MACHINE STEEL UNS G87400,CADMIUM PLATE, DRILLED, 1 HOLEHEXAGON HEAD, .1640-36 UNJF-3ATABLE 1 - PART NUMBERS AND DIMENSIONSPARTNUMBER L KAPPROXMASSLB/100PARTNUMBER L KAPPROXMASSLB/100MS9528-03MS9528-04MS9528-05MS9528-06
9、MS9528-07MS9528-08MS9528-09MS9528-10MS9528-11MS9528-12MS9528-13MS9528-14MS9528-15.302 - .322.365 - .385.428 - .448.490 - .510.552 - .572.615 - .635.678 - .698.740 - .760.802 - .822.865 - .885.928 - .948.990 - 1.0101.052 - 1.072.062- .082.062- .082.062- .082.062- .082.062- .082.062- .082.062- .110.11
10、2- .172.174- .234.237- .297.300- .360.362- .422.424- .484.43.46.49.53.56.59.62.65.69.72.75.78.81MS9528-16MS9528-17MS9528-18MS9528-19MS9528-20MS9528-21MS9528-22MS9528-23MS9528-24MS9528-25MS9528-26MS9528-27MS9528-281.115 - 1.1351.178 - 1.1981.240 - 1.2601.302 - 1.3221.365 - 1.3851.428 - 1.4481.490 - 1
11、5101.552 - 1.5721.615 - 1.6351.678 - 1.6981.740 - 1.7601.865 - 1.8851.990 - 2.010.487 - .547.550 - .610.612 - .672.674 - .734.737 - .797.800 - .860.862 - .922.924 - .984.987 - 1.0471.050 - 1.1101.112 - 1.1721.237 - 1.2971.362 - 1.425.84.88.91.94.971.001.041.071.101.131.161.231.29NOTES:NOTICETHIS DO
12、CUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE ANY QUESTIONS CONCERNING CADMIUMS USE./1/ FOR PART NUMBERS MS9528-03 THROUGH MS9528-13 DATUM Z SHALL REPLACE DATUM Y.2. MATERIAL: LOW ALLOY STEEL AMS6322 (UNS G87400)./3/ PROCUREMENT SPECIFICAT
13、ION: AS7452, EXCEPT HEAD SHALL BE UPSET.4. FINISH: CADMIUM PLATE PER AMS2400. DIMENSIONS ARE AFTER PLATING.5. MAGNETIC PARTICLE INSPECTION PER ASTM E1444/E1444M.6. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra.7.
14、 BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED.8. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION).9. DIMENSIONS IN INCHES.10. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND
15、 USED UNTIL STOCK IS DEPLETED.11. DO NOT USE UNASSIGNED PART NUMBERS.12. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R
16、) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS.ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION.ASTM IS AN ASTM INTERNATIONAL PUBLICATION.
