1、AEROSPACE STANDARDBOLT, MACHINE STEEL UNS G87400CADMIUM PLATE, DRILLED, 1 HOLEHEXAGON HEAD, 1900-32 UNJF-3AAS9529Copyright 2016 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, m
2、echanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUED1999-12 REAFFIR
3、MED2004-07 REVISED2016-06THIRD ANGLE PROJECTIONCUSTODIAN: E-25REV.BFEDERAL SUPPLY CLASS5306AS9529SHEET 1 OF 3REV.BPROCUREMENT SPECIFICATION: AS7452, SEE NOTE /3/SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengineering sciences. The use of th
4、isreport isentirelyvoluntary, andits applicability andsuitability for any particularuse, includingany patent infringement arising therefrom,is the soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,stabilized,orcancelled.SAEinvites
5、 yourwritten comments andsuggestions.SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS9529BRATIONALEADD DIAMETER SYMBOL TO FEATURE CONTROL FRAME FOR STRAIGHTNESS CALLOUT, UPDATE ANSI Y14.5M SYMBOLS AND FORMATTING, RELOCATE W DAT
6、UM AND ADD A TERTIARY DATUM FOR DRILLED HOLE POSITION, UPDATE COLD ROLLING NOTE, ADD NOTE FOR USAGE OF EXISTING INVENTORY, ADD EDGE DISTANCE EXCEPTION FOR HEAD MARKING, FIGURE 1 REDRAWN, GENERAL EDITORIAL UPDATE.NOTICETHE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY
7、 STANDARD MS9529, AMENDMENT 1 NOTICE 1. THIS SAE STANDARD RETAINS THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT.ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPLS) MAY CONTINUE TO BEMANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY
8、 THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT.FIGURE 1 - BOLTAEROSPACE STANDARDAS9529SHEET 2 OF 3REV.BBOLT, MACHINE STEEL UNS G87400CADMIUM PLATE, DRILLED, 1 HOLEHEXAGON HEAD, 1900-32 UNJF-3ATABLE 1 - PART NUMBERS AND DIMENSIONSDASHNUMBER L KAPPROXMASSLB/100DASHNUMBER L KAPPROXMAS
9、SLB/100MS9529-04MS9529-05MS9529-06MS9529-07MS9529-08MS9529-09MS9529-10MS9529-11MS9529-12MS9529-13MS9529-14MS9529-15MS9529-16MS9529-17MS9529-18MS9529-19MS9529-20MS9529-21MS9529-22MS9529-23.365 - .385.428 - .448.490 - .510.552 - .572.615 - .635.678 - .698.740 - .760.802 - .822.865 - .885.928 - .948.99
10、0 - 1.0101.052 - 1.0721.115 - 1.1351.178 - 1.1981.240 - 1.2601.302 - 1.3221.365 - 1.3851.428 - 1.4481.490 - 1.5101.552 - 1.572.072 - .092.072 - .092.072 - .092.072 - .092.072 - .092.072 - .092.072 - .120.122 - .182.185 - .245.248 - .308.310 - .370.372 - .432.435 - .495.498 - .558.560 - .620.622 - .6
11、82.685 - .745.748 - .808.810 - .870.872 - .932.66.70.74.78.82.86.90.94.981.021.071.111.151.191.231.271.311.351.391.43MS9529-24MS9529-25MS9529-26MS9529-27MS9529-28MS9529-29MS9529-30MS9529-31MS9529-32MS9529-33MS9529-34MS9529-35MS9529-36MS9529-37MS9529-38MS9529-39MS9529-40MS9529-41MS9529-42MS9529-431.6
12、15 - 1.6351.678 - 1.6981.740 - 1.7601.865 - 1.8851.990 - 2.0102.115 - 2.1352.240 - 2.2602.365 - 2.3852.490 - 2.5102.615 - 2.6352.740 - 2.7602.865 - 2.8852.990 - 3.0103.115 - 3.1353.240 - 3.2603.365 - 3.3853.490 - 3.5103.615 - 3.6353.740 - 3.7603.865 - 3.885.935 - .995.998 - 1.0581.060 - 1.1201.185 -
13、 1.2451.310 - 1.3701.435 - 1.4951.560 - 1.6201.685 - 1.7451.810 - 1.8701.935 - 1.9952.060 - 2.1202.185 - 2.2452.310 - 2.3702.435 - 2.4952.560 - 2.6202.685 - 2.7452.810 - 2.8702.935 - 2.9953.060 - 3.1203.185 - 3.2451.471.511.551.631.711.791.871.952.032.112.192.272.352.432.512.592.672.752.832.91NOTICE
14、THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOUHAVE QUESTIONS CONCERNING CADMIUMS USE.NOTES:/1/ FOR PART NUMBERS MS9529-04 THROUGH MS9529-14 DATUM Z SHALL REPLACE DATUM Y.2. MATERIAL: LOW ALLOY STEEL AMS6322 (UNS G87400)./3/ PROCUREMENT SP
15、ECIFICATION: AS7452, EXCEPT HEAD SHALL BE UPSET.4. HEAD TO SHANK FILLET RADIUS: FOR PART NUMBERS MS9529-13 AND LARGER, THE HEAD TO SHANK FILLET SHALL BE COLD ROLLED AFTER HEAT TREATMENT. COLD ROLLING SHALL BE SUFFICIENT TO REMOVE ALL VISUAL EVIDENCE OF GRINDING OR TOOL MARKS.5. FINISH: CADMIUM PLATE
16、 PER AMS2400. DIMENSIONS ARE AFTER PLATING.6. MAGNETIC PARTICLE INSPECTION PER ASTM E1444/E1444M.7. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra.8. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED.9. D
17、IMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION).10. DIMENSIONS IN INCHES.AEROSPACE STANDARDAS9529SHEET 3 OF 3REV.BBOLT, MACHINE STEEL UNS G87400CADMIUM PLATE, DRILLED, 1 HOLEHEXAGON HEAD, 1900-32 UNJF-3A11. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVIS
18、IONS OF THE APPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED12. DO NOT USE UNASSIGNED PART NUMBERS.13. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHA
19、NGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS.ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION.ASTM IS AN ASTM INTERNATIONAL PUBLICATION.
