1、 AEROSPACE STANDARD BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, CORROSION AND HEAT RESISTANT STEEL, UNS S66286, UTS 130 KSI MIN, .3750-24 UNJF-3AAS9559Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmi
2、tted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE W
3、EB ADDRESS: http:/www.sae.org ISSUED 1999-04REVISED 2013-01THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.D FEDERAL SUPPLY CLASS 5306 AS9559 SHEET 1 OF 3 REV. D PROCUREMENT SPECIFICATION: AS7477SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technic
4、alandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay ber
5、eaffirmed, revised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS9559D RATIONALE WRONG THREAD DESIGNATION CORRECTED IN FIGURE 1. NOTICE THE INITIAL SAE PUBLICATION
6、 OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9559E, AMENDMENT 2. THIS SAE STANDARD MAY RETAIN THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQ
7、UIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE 1 - BOLT AEROSPACE STANDARD AS9559 SHEET 2 OF 3 REV. D BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, CORROSION AND HEAT RESISTANT STEEL, UNS S66286, UTS 130 KSI MIN, .37
8、50-24 UNJF-3A TABLE 1 - PART NUMBERS AND DIMENSIONS PART NUMBER L K APPROX MASS LBF/100 PART NUMBER L K APPROX MASS LBF/100 MS9559-03 . 552 - .572 .088 - .108 3.26 MS9559-31 2.865 - 2.885 1.815 - 1.875 9.46 MS9559-04 .615 - .635 .088 - .108 3.42 MS9559-32 2.990 - 3.010 1.940 - 2.000 9.80 MS9559-05 .
9、678 - .698 .088 - .108 3.58 MS9559-33 3.115 - 3.135 2.065 - 2.125 10.13 MS9559-06 .740 - .760 .088 - .108 3.74 MS9559-34 3.240 - 3.260 2.190 - 2.250 10.47 MS9559-07 .802 - .822 .088 - .108 3.90 MS9559-35 3.365 - 3.835 2.315 - 2.375 10.80 MS9559-08 .865 - .885 .088 - .108 4.07 MS9559-36 3.490 - 3.510
10、 2.440 - 2.500 11.14 MS9559-09 .928 - .948 .088 - .108 4.24 MS9559-37 3.615 - 3.635 2.565 - 2.625 11.47 MS9559-10 .990 - 1.010 .088 - .108 4.41 MS9559-38 3.740 - 3.760 2.690 - 2.750 11.80 MS9559-11 1.052 - 1.072 .088 - .108 4.58 MS9559-39 3.865 - 3.885 2.815 - 2.875 12.14 MS9559-12 1.115 - 1.135 .08
11、8 - .125 4.75 MS9559-40 3.990 - 4.010 2.940 - 3.000 12.47 MS9559-13 1.178 - 1.198 .128 - .188 4.91 MS9559-41 4.115 - 4.135 3.065 - 3.125 12.80 MS9559-14 1.240 - 1.260 .190 - .250 5.08 MS9559-42 4.240 - 4.260 3.190 - 3.250 13.13 MS9559-15 1.302 - 1.322 .252 - .312 5.25 MS9559-43 4.365 - 4.385 3.315 -
12、 3.375 13.46 MS9559-16 1.365 - 1.385 .315 - .375 5.43 MS9559-44 4.490 - 4.510 3.440 - 3.500 13.89 MS9559-17 1.428 -1.448 .378 - .438 5.60 MS9559-45 4.615 - 4.635 3.565 - 3.625 14.23 MS9559-18 1.490 - 1.510 .440 - .500 5.76 MS9559-46 4.740 - 4.760 3.690 - 3.750 14.56 MS9559-19 1.552 - 1.572 .502 - .5
13、62 5.93 MS9559-47 4.865 - 4.885 3.815 - 3.875 14.89 MS9559-20 1.615 - 1.635 .565 - .625 6.10 MS9559-48 4.990 - 5.010 3.940 - 4.000 15.23 . MS9559-21 1.678 - 1.698 .628 - .688 6.27 MS9559-49 5.115 -5.135 4.065 - 4.125 15.57 MS9559-22 1.740 - 1.760 .690 - .750 6.44 MS9559-50 5.240 - 5.260 4.190 - 4.25
14、0 15.90 MS9559-57 1.802 - 1.822 .752 - .812 6.61 MS9559-51 5.365 - 5.385 4.315 - 4.375 16.23 MS9559-23 1.865 - 1.885 .815 - .875 6.77 MS9559-52 5.490 - 5.510 4.440 - 4.500 16.58 MS9559-58 1.928 - 1.948 .878 - .938 6.94 MS9559-53 5.615 -5.635 4.565 - 4.625 16.89 MS9559-24 1.990 - 2.010 .940 - 1.000 7
15、11 MS9559-54 5.740 - 5.760 4.690 - 4.750 17.23 MS9559-25 2.115 - 2.135 1.065 - 1.125 7.44 MS9559-55 5.865 - 5.885 4.815 - 4.875 17.57 MS9559-26 2.240 - 2.260 1.190 - 1.250 7.78 MS9559-56 5.990 - 6.010 4.940 - 5.000 17.91 MS9559-27 2.365 - 2.385 1.315 - 1.375 8.11 MS9559-28 2.490 - 2.510 1.440 - 1.5
16、00 8.44 MS9559-29 2.615 - 2.635 1.565 - 1.625 8.78 MS9559-30 2.740 - 2.760 1.690 - 1.750 9.12 DASH NUMBERS 57 AND 58 ARE IN LENGTH ORDER AEROSPACE STANDARD AS9559 SHEET 3 OF 3 REV. D BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, CORROSION AND HEAT RESISTANT STEEL, UNS S66286, UTS 130 KSI MIN,
17、 .3750-24 UNJF-3A NOTES: 1. FOR PART NUMBERS MS9559-03 THRU MS9559-18 THE THREAD PD (DATUM -Z- ) SHALL REPLACE DATUM -Y- . 2. MATERIAL: CORROSION AND HEAT RESISTANT STEEL PER AMS5731 (UNS S66286). 3. PROCUREMENT SPECIFICATION: AS7477. 4. HEAD TO SHANK FILLET: HEAD TO SHANK FILLET SHALL BE ROLLED AFT
18、ER HEAT TREATMENT TO REMOVE ALL EVIDENCE OF GRINDING OR TOOL MARKS EXCEPT PART NUMBER MS9559-14 AND SMALLER DO NOT REQUIRE FILLET ROLLING. 5. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417, TYPE 1, SENSITIVITY LEVEL 2. 6. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLES
19、S OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 7. BREAK EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 8. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 9. DIMENSIONS IN INCHES. 10. DO NOT USE UNASSIGNED PART NUMBERS. 11. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN
20、 IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.
