1、 AEROSPACE STANDARD SCREW, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, DRILLED, PD SHANK, SILVER PLATED, CORROSION AND HEAT RESISTANT STEEL, UNS S66286, 130 KSI MIN, .1640-36 UNJF-3A AS9573Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored
2、in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Ema
3、il: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2000-08REAFFIRMED2007-06REVISED 2017-10THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.C FEDERAL SUPPLY CLASS 5305 AS9573 SHEET 1 OF 2 REV. C PROCUREMENT SPECIFICATION: AS7477 SAE Technical Standards Board Rules provide that: “This repo
4、rt ispublished by SAEtoadvance thestate of technicalandengineering sciences. Theuse of thisreport is entirely voluntary, andits applicabilityand suitability forany particular use, including any patent infringement arisingtherefrom, isthesole responsibility of theuser.”SAE reviews eachtechnicalreport
5、 at least everyfive years at which timeitmay berevised, reaffirmed, stabilized, orcancelled. SAE invitesyourwrittencomments andsuggestions. SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS9573C RATIONALE NOTE 5 FLUORESCENT PENETRANT INSPECT
6、ION REFERENCE SPEC CORRECTED, TABLE 1 PUT IN LENGTH ORDER FOR MS9573-29 AND MS9573-30. NOTICE THE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9573B. THIS SAE STANDARD MAY RETAIN THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQ
7、UIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPLS) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE 1 - SCREW AEROSPACE STANDARD AS9573 SHEET 2 OF 2 REV. C SCREW, MACH
8、INE - DOUBLE HEXAGON EXTENDED WASHER HEAD, DRILLED, PD SHANK, SILVER PLATED, CORROSION AND HEAT RESISTANT STEEL, UNS S66286, 130 KSI MIN, .1640-36 UNJF-3A TABLE 1 - PART NUMBERS AND DIMENSIONS PART NO. L K APPROX MASS LB/100 PART NO. L K APPROX MASS LB/100 MS9573-02 .240- .260 .062-.082 .420 MS9573-
9、17 1.178-1.198 .550- .610 .878 MS9573-03 .302- .322 .062-.082 .451 MS9573-18 1.240-1.260 .612- .672 .908 MS9573-04 .365- .385 .062-.082 .482 MS9573-19 1.302-1.322 .674- .734 .938 MS9573-05 .428- .448 .062-.082 .513 MS9573-20 1.365-1.385 .737- .797 .969 MS9573-06 .490- .510 .062-.082 .543 MS9573-21 1
10、428-1.448 .800- .860 .999 MS9573-07 .552- .572 .062-.082 .573 MS9573-22 1.490-1.510 .862- .922 1.029 MS9573-08 .615- .635 .062-.082 .604 MS9573-23 1.552-1.572 .924- .984 1.060 MS9573-09 .678- .698 .062-.110 .634 MS9573-24 1.615-1.635 .987-1.047 1.090 MS9573-10 .740- .760 .112-.172 .664 MS9573-25 1.
11、678-1.698 1.050-1.110 1.121 MS9573-11 .802- .822 .174-.234 .695 MS9573-26 1.740-1.760 1.112-1.172 1.151 MS9573-12 .865- .885 .237-.297 .725 MS9573-29 1.802-1.822 1.174-1.234 1.181 MS9573-13 .928- .948 .300-.360 .756 MS9573-27 1.865-1.885 1.237-1.297 1.212 MS9573-14 .990-1.010 .362-.422 .786 MS9573-3
12、0 1.928-1.948 1.300-1.360 1.242 MS9573-15 1.052-1.072 .424-.484 .816 MS9573-28 1.990-2.010 1.362-1.422 1.273 MS9573-16 1.115-1.135 .487-.547 .847 NOTES 1. FOR PART NUMBERS MS9573-02 THROUGH MS9573-12 DATUM Z SHALL REPLACE DATUM Y. 2. MATERIAL: CORROSION AND HEAT RESISTANT STEEL PER AMS5731 (UNS S662
13、86). 3. PROCUREMENT SPECIFICATION: AS7477. 4. FINISH: SILVER PLATE PER AMS2411 .0002 TO .0006 THICK AT THREAD PD. DIMENSIONS SPECIFIED ARE AFTER PLATING. PD MAY BE REDUCED .0012 MAXIMUM BEFORE PLATING. 5. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MINIMUM, BE
14、FORE PLATING. 6. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 7. BREAK EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 8. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 9. DIMENSIONS ARE
15、IN INCHES. 10. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED. 11. DO NOT USE UNASSIGNED PART NUMBERS. 12. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR
16、 THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.
