1、 AEROSPACE STANDARD BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, DRILLED, PD SHANK, SILVER PLATED, CORROSION AND HEAT RESISTANT STEEL, UNS S66286, 130KSI MIN, .3125-24 UNJF-3A AS9576Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in
2、 a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email
3、: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1999-08REVISED 2017-10THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.D FEDERAL SUPPLY CLASS 5306 AS9576 SHEET 1 OF 3 REV. D PROCUREMENT SPECIFICATION: AS7477 SAE Technical Standards Board Rules provide that: “This report ispublished by S
4、AEtoadvance thestate of technicalandengineering sciences. Theuse of thisreport is entirely voluntary, andits applicabilityand suitability forany particular use, including any patent infringement arisingtherefrom, isthesole responsibility of theuser.”SAE reviews eachtechnicalreport at least everyfive
5、 years at which timeitmay berevised, reaffirmed, stabilized, orcancelled. SAE invitesyourwrittencomments andsuggestions. SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS9576D RATIONALE NOTE 5 FLUORESCENT PENETRANT INSPECTION REFERENCE SPEC
6、CORRECTED, TABLE 1 PUT IN LENGTH ORDER FOR MS9576-59 AND MS9576-60. NOTICE THE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9576D, AMENDMENT 1, NOTICE 1. THIS SAE STANDARD MAY RETAIN THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY
7、 REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPLS) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE 1 - BOLT AEROSPACE STANDARD AS9576 SHEET 2 OF 3 REV. D BOLT, MA
8、CHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, DRILLED, PD SHANK, SILVER PLATED, CORROSION AND HEAT RESISTANT STEEL, UNS S66286, 130KSI MIN, .3125-24 UNJF-3A TABLE 1 - PART NUMBERS AND DIMENSIONS PART NO. L K APPROX MASS LB/100 PART NO. L K APPROX MASS LB/100 MS9576-04 .490- .510 .088- .108 2.06 MS957
9、6-32 2.740-2.760 1.815-1.875 6.13 MS9576-05 .552- .572 .088- .108 2.17 MS9576-33 2.865-2.885 1.940-2.000 6.36 MS9576-06 .615- .635 .088- .108 2.28 MS9576-34 2.990-3.010 2.065-2.125 6.58 MS9576-07 .678- .698 .088- .108 2.39 MS9576-35 3.115-3.135 2.190-2.250 6.80 MS9576-08 .740- .760 .088- .108 2.51 M
10、S9576-36 3.240-3.260 2.315-2.375 7.03 MS9576-09 .802- .822 .088- .108 2.62 MS9576-37 3.365-3.385 2.440-2.500 7.27 MS9576-10 .865- .885 .088- .108 2.73 MS9576-38 3.490-3.510 2.565-2.625 7.50 MS9576-11 .928- .948 .088- .108 2.85 MS9576-39 3.615-3.635 2.690-2.750 7.73 MS9576-12 .990-1.010 .088- .125 2.
11、96 MS9576-40 3.740-3.760 2.815-2.875 7.95 MS9576-13 1.052-1.072 .128- .188 3.07 MS9576-41 3.865-3.885 2.940-3.000 8.17 MS9576-14 1.115-1.135 .190- .250 3.19 MS9576-42 3.990-4.010 3.065-3.125 8.40 MS9576-15 1.178-1.198 .252- .312 3.30 MS9576-43 4.115-4.135 3.190-3.250 8.63 MS9576-16 1.240-1.260 .315-
12、 .375 3.41 MS9576-44 4.240-4.260 3.315-3.375 8.86 MS9576-17 1.302-1.322 .378- .438 3.52 MS9576-45 4.365-4.385 3.440-3.500 9.08 MS9576-18 1.365-1.385 .440- .500 3.64 MS9576-46 4.490-4.510 3.565-3.625 9.30 MS9576-19 1.428-1.448 .502- .562 3.75 MS9576-47 4.615-4.635 3.690-3.750 9.52 MS9576-20 1.490-1.5
13、10 .565- .625 3.87 MS9576-48 4.740-4.760 3.815-3.875 9.74 MS9576-21 1.552-1.572 .628- .688 3.98 MS9576-49 4.865-4.885 3.940-4.000 9.95 MS9576-22 1.615-1.635 .690- .750 4.10 MS9576-50 4.990-5.010 4.065-4.125 10.17 MS9576-23 1.678-1.698 .752- .812 4.22 MS9576-51 5.115-5.135 4.190-4.250 10.40 MS9574-24
14、 1.740-1.760 .815- .875 4.33 MS9576-52 5.240-5.260 4.315-4.375 10.63 MS9576-59 1.802-1.822 .878- .938 4.44 MS9576-53 5.365-5.385 4.440-4.500 10.86 MS9576-25 1.865-1.885 .940-1.000 4.55 MS9576-54 5.490-5.510 4.565-4.625 11.10 MS9576-60 1.928-1.948 1.002-1.062 4.66 MS9576-55 5.615-5.635 4.690-4.750 11
15、.33 MS9576-26 1.990-2.010 1.065-1.125 4.77 MS9576-56 5.740-5.760 4.815-4.875 11.56 MS9576-27 2.115-2.135 1.190-1.250 5.00 MS9576-57 5.865-5.885 4.940-5.000 11.78 MS9576-28 2.240-2.260 1.315-1.375 5.23 MS9576-58 5.990-6.010 5.065-5.125 12.00 MS9576-29 2.365-2.385 1.440-1.500 5.45 MS9576-30 2.490-2.51
16、0 1.565-1.625 5.67 MS9576-31 2.615-2.635 1.690-1.750 5.90 NOTES 1. FOR PART NUMBERS MS9576-04 THROUGH MS9576-16 DATUM Z SHALL REPLACE DATUM Y. 2. MATERIAL: CORROSION AND HEAT RESISTANT STEEL PER AMS5731 (UNS S66286). 3. PROCUREMENT SPECIFICATION: AS7477. 4. FINISH: SILVER PLATE PER AMS2411 .0002 TO
17、.0006 THICK AT THREAD PD. DIMENSIONS SPECIFIED ARE AFTER PLATING. PD MAY BE REDUCED .0012 MAXIMUM BEFORE PLATING. 5. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MINIMUM, BEFORE PLATING. 6. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1.
18、 UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 7. BREAK EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 8. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 9. DIMENSIONS ARE IN INCHES. AEROSPACE STANDARD AS9576 SHEET 3 OF 3 REV. D BOLT, MACHINE - DOUBLE HEXAGON
19、EXTENDED WASHER HEAD, DRILLED, PD SHANK, SILVER PLATED, CORROSION AND HEAT RESISTANT STEEL, UNS S66286, 130KSI MIN, .3125-24 UNJF-3A 10. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DE
20、PLETED. 11. DO NOT USE UNASSIGNED PART NUMBERS. 12. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT
21、OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.
