1、AEROSPACE STANDARD WASHER, KEY - 270 DEG, LOCKING, CRES, UNS S32100 AS9582Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or
2、 otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1998-11REAFFIRMED 2007-06 REVISED 2014-04THIRD AN
3、GLE PROJECTION CUSTODIAN: E-25 REV.CFEDERAL SUPPLY CLASS 5310 AS9582SHEET 1 OF 3REV. CPROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineeringsciences.The useofthis reportisentirelyvoluntary, andits
4、applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments an
5、dsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS9582CRATIONALE DIMENSION N CORRECTED. NOW SHOWING DIMENSIONED TO CORRECT SURFACE. NOTICE THE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MI
6、LITARY STANDARD MS9582B, NOTICE 1. THIS SAE STANDARD MAY RETAIN THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY
7、THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. H BV.010 AVRAD MBOTH SIDES.020.030RNTSEE NOTE 3PDELENGTH BEFOREBENDINGRAD LBOTH SIDESRADIUS TO BLEND2 PLACESJBEFORE BENDINGGRAD KDIRECTION OF GRAINS.060.040RR.010.020.005WITHIN DTO INTERSECTION 10 - 2063FIGURE 1 - WASHER AEROSPACE STAN
8、DARD AS9582SHEET 2 OF 3REV. CWASHER, KEY - 270 DEG, LOCKING, CRES, UNS S32100 TABLE 1 - DIMENSIONS TABLE 1 - DIMENSIONS (CONTINUED) NOTES: 1. MATERIAL: CORROSION RESISTANT STEEL AMS5510 (UNS S32100). 2. HEAT TREATMENT: FORMED WASHERS SHALL BE STRESS RELIEVED AT 1600 F 25 F FOR 30 MINUTES IN A PROTEC
9、TIVE ATMOSPHERE FOLLOWED BY AIR COOL. 3. DIMENSION “T“ SHALL BE OF UNIFORM THICKNESS WITHIN .002. 4. REMOVE BURRS AND SHARP EDGES. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 6. IDENTIFICATION: MARK PART NU
10、MBER AND MANUFACTURERS IDENTIFICATION ON CONTAINER. 7. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 8. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED. AEROSPACE STANDARD AS9582SHEET 3 OF 3REV. CWASHER, KEY - 270 DEG, LOCKING, CRES, UNS S32100 9. DO NOT USE UNASSIGNED PART
11、NUMBERS. 10. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION.
