1、 AEROSPACE STANDARD BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, PD SHANK, CORROSION AND HEAT RESISTANT STEEL, UNS N07001, 165 KSI MIN, .3125-24 UNJF-3AAS9698 Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or
2、transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org S
3、AE WEB ADDRESS: http:/www.sae.org ISSUED 2003-09REVISED 2007-07 THIRD ANGLE PROJECTION CUSTODIAN: SAE E-25 REV. B FEDERAL SUPPLY CLASS5306 AS9698 SHEET 1 OF 3 REV. B SAE TechnicalStandards Board Rules provide that: “This report is published by SAE toadvance thestate of technical andengineering scien
4、ces. Theuse of thisreportis entirely voluntary, andits applicabilityandsuitability forany particularuse,including any patent infringement arising therefrom, is thesole responsibility oftheuser.” SAE reviews each technical report at least every five yearsat which time it may be reaffirmed, revised, o
5、rcancelled.SAE invites yourwritten commentsandsuggestions. RATIONALE REDRAWN TO PROVIDE ALTERNATIVE METHOD OF MANUFACTURER OF THE LIGHTENING HOLE. NOTICE THE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9698A, NOTICE 1. THIS SAE STANDARD RETAINS THE SAME
6、PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE 1
7、 - BOLT Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, PD SHANK, CORROSION AND HEAT RESISTANT STEEL, UNS N07001, 165 KSI MIN,
8、3125-24 UNJF-3A AS9698 REV. B AS9698 SHEET 2 OF 3 REV. B Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, PD SHANK, CORROSION A
9、ND HEAT RESISTANT STEEL, UNS N07001, 165 KSI MIN, .3125-24 UNJF-3A AS9698 REV. B AS9698 SHEET 3 OF 3 REV. B NOTES: 1. FOR PART NUMBERS MS9698-04 THRU MS9698-14 THE THREAD PD (DATUM -Z- ) SHALL REPLACE DATUM -Y- . 2. MATERIAL: CORROSION AND HEAT RESISTANT STEEL PER AMS 5708 (UNS N07001). 3. PROCUREME
10、NT SPECIFICATION: AS7471. 4. FLUORESCENT PENETRANT INSPECTION PER ASTM E 1417. 5. HEAD TO SHANK FILLET SHALL BE COLD ROLLED AFTER HEAT TREATMENT TO REMOVE ALL VISUAL EVIDENCE OF GRINDING OR TOOL MARKS, EXCEPT PART NUMBERS MS9698-14 AND SMALLER. 6. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREME
11、NTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 7. MARK PART NUMBER AND MANUFACTURERS IDENTIFICATION PER AS478 CLASS A, EXCEPT EDGE DISTANCE REQUIREMENTS WAIVED. 8. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 9. DIMENSIONS ARE IN INCHES. 10. DIMENSI
12、ONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION) 11. DO NOT USE UNASSIGNED PART NUMBERS. 12. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THI
13、S DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN AMERICAN SOCIETY FOR TESTING AND MATERIALS PUBLICATION. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
