1、AEROSPACE STANDARD BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, DRILLED, PD SHANK, AMS4967 (TI 6AL-4V), .1900-32 UNJF-3A AS9759Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by a
2、ny means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae
3、org ISSUED 2000-08REAFFIRMED2005-05REVISED 2014-08THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.AFEDERAL SUPPLY CLASS 5306 AS9759SHEET 1 OF 2REV. APROCUREMENT SPECIFICATION: AS7461SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandenginee
4、ringsciences.The useofthis reportisentirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed
5、 stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS9759ARATIONALE GENERAL REVISION. REVISE LIGHTENING HOLE CONFIGURATION (ADD SECTION VIEW) TO ALLOW OPTION
6、AL SHAPE AT BOTTOM OF HOLE, ADD EXCEPTION TO EDGE DISTANCE REQUIREMENTS FOR HEAD MARKING, UPDATE THREAD SPECIFICATION TO AS8879, UPDATE SURFACE FINISH REQUIREMENTS, ADD AS3062 AND DELETE NOTE ON FILLET FOR INCOMPLETE THREAD REQUIREMENTS, ADD DATUM REQUIREMENTS FOR -03 THRU -14 LENGTHS (NEW NOTE 1),
7、UPDATE DIMENSIONING AND TOLERANCING TO ANSI Y14.5M-1982, DELETE .015 MAX RADIUS AT BASE OF WRENCH PAD, DELETE HARDNESS NOTE, AND FIGURE 1 REDRAWN. NOTICE THE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9759, NOTICE 1. THIS SAE STANDARD MAY RETAIN THE SAM
8、E PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE
9、 1 - BOLT AEROSPACE STANDARD AS9759SHEET 2 OF 2REV. ABOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, DRILLED, PD SHANK AMS4967 (TI 6AL-4V), .1900-32 UNJF-3ATABLE 1 PART NUMBERS AND DIMENSIONS PARTNUMBER L K APPROX WEIGHT LB/100 PARTNUMBER L K APPROX WEIGHT LB/100 MS9759-03 .302- .322 .072-.092
10、384 MS9759-24 1.615-1.635 .935- .995 .857 MS9759-04 .365- .385 .072-.092 .407 MS9759-25 1.678-1.698 .998-1.058 .880 MS9759-05 .428- .448 .072-.092 .430 MS9759-26 1.740-1.760 1.060-1.120 .902 MS9759-06 .490- .510 .072-.092 .452 MS9759-27 1.802-1.822 1.122-1.182 .924 MS9759-07 .552- .572 .072-.092 .4
11、74 MS9759-28 1.865-1.885 1.185-1.245 .947 MS9759-08 .615- .635 .072-.092 .497 MS9759-29 1.990-2.010 1.310-1.370 .992 MS9759-09 .678- .698 .072-.092 .520 MS9759-30 2.115-2.135 1.435-1.495 1.037 MS9759-10 .740- .760 .072-.120 .542 MS9759-31 2.240-2.260 1.560-1.620 1.082 MS9759-11 .802- .822 .122-.182
12、564 MS9759-32 2.365-2.385 1.685-1.740 1.127 MS9759-12 .865- .885 .185-.245 .587 MS9759-33 2.490-2.510 1.810-1.870 1.172 MS9759-13 .928- .948 .248-.308 .610 MS9759-34 2.615-2.635 1.935-1.995 1.217 MS9759-14 .990-1.010 .310-.370 .632 MS9759-35 2.740-2.760 2.060-2.120 1.262 MS9759-15 1.052-1.072 .372-
13、432 .654 MS9759-36 2.865-2.885 2.185-2.245 1.307 MS9759-16 1.115-1.135 .435-.495 .677 MS9759-37 2.990-3.010 2.310-2.370 1.352 MS9759-17 1.178-1.198 .498-.558 .700 MS9759-38 3.115-3.135 2.435-2.495 1.397 MS9759-18 1.240-1.260 .560-.620 .722 MS9759-39 3.240-3.260 2.560-2.620 1.442 MS9759-19 1.302-1.3
14、22 .622-.682 .744 MS9759-40 3.365-3.385 2.685-2.745 1.487 MS9759-20 1.365-1.385 .685-.745 .767 MS9759-41 3.490-3.510 2.810-2.870 1.532 MS9759-21 1.428-1.448 .748-.808 .790 MS9759-42 3.615-3.635 2.935-2.995 1.577 MS9759-22 1.490-1.510 .810-.870 .812 MS9759-43 3.740-3.760 3.060-3.120 1.622 MS9759-23 1
15、552-1.572 .872-.932 .834 MS9759-44 3.865-3.885 3.185-3.245 1.667 NOTES: 1. FOR PART NUMBERS MS9759-03 THRU MS9759-14 DATUM Z SHALL REPLACE DATUM Y.2. PROCUREMENT SPECIFICATION: AS7461. 3. MATERIAL: AMS4967 (TITANIUM ALLOY 6AL-4V, COMPOSITION SIMILAR TO UNS R56400). 4. FLUORESCENT PENETRANT INSPECTI
16、ON PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MIN 5. SURFACE TEXTURE SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra EXCEPT UPSET HEAD. 6. BREAK SHARP EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONS IN INCHES.
17、8. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 9. DO NOT USE UNASSIGNED PART NUMBERS. 10. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE
18、OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.
