1、 6$(7HFKQLFDO6WDQGDUGV%RDUG5XOHVSURYLGHWKDW7KLVUHSRUWLVSXEOLVKHGE6$(WRDGYDQFHWKHVWDWHRIWHFKQLFDODQGHQJLneering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particulDUXVHLQFOXGLQJDQSDWHQWLQIULQJHPHQWDULVLQJWKHUHIURPLVWKHVROHUHVSRQVLELOLWRIWKHX
2、VHU SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a r
3、etrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: Cu
4、stomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/J1835_201401 SURFACE VEHICLE RECOMMENDED PRACTICE J1835 JAN2014 Issued 1990-03 Revised 2014-01 Superseding J1835 MAY2004 Fas
5、tener Hardware for Wheels for Demountable Rims RATIONALE This document is being updated to current standards and to correct some tables to prepare this document to be stabilized at a later date. 1. SCOPE This SAE Recommended Practice establishes the mounting hardware to be used with demountable rims
6、 wheels for demountable rims, rim spacers designed for 28 degrees bevel mounting systems, and intended for use on commercial vehicles. The dimensions given are those necessary to maintain serviceability and interchangeability of mounting hardware. This document is divided into two sections. Section
7、 1 establishes the practice for new designs for mounting hardware. Section 2 records information on current mounting hardware. Special and less common applications are not covered in this document. 2. REFERENCES 2.1 Applicable Documents The following publications form a part of this specification to
8、 the extent specified herein. Unless otherwise indicated, the latest issue of SAE publications shall apply. 2.1.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org
9、 SAE J393 Nomenclature - Wheels, Hubs, and Rims for Commercial Vehicles SAE J851 Dimensions - Wheels for Demountable Rims, Demountable Rims, and Spacer Bands - Truck and Bus 3. DEFINITIONS A detailed listing of basic nomenclature is contained in SAE J393. Figures 1 through 8 and Tables 1 through 3,
10、 introduce, illustrate, and specify additional nomenclature and definitions. All dimensions are in inches unless otherwise specified. Single clamps are rim clamps with one hole and double clamps are rim clamps with two holes. SAE J1835 Revised JAN2014 Page 2 of 7 4. SECTION 1 - MOUNTING HARDWARE DIM
11、ENSIONS (RECOMMENDED PRACTICE) 4.1 Rim Clamp Nut FIGURE 1 - RIM CLAMP NUT 4.2 Rim Clamp Stud Standout FIGURE 2 - RIM CLAMP STUD STANDOUT SAE J1835 Revised JAN2014 Page 3 of 7 4.3 Rim Clamp Dimensions 4.3.1 Dual Mounting 4.3.1.1 Dual Assembly FIGURE 3 - DUAL ASSEMBLY, DROP CENTER RIMS SHOWN TABLE 1 -
12、 DIMENSIONS FOR SINGLE CLAMPS (DUAL MOUNTING), REFER TO FIGURE 3 (A) Spacer Width +0.060 0.047 (B) Rim Clamp Toe Length 0.05 (C) Spoke Length 0.06 (D) Rim Bevel Intersection (28 degrees Layout Line) 0.040 (E) 28 degrees Bevel Layout Diameter (Nominal Wheel Diameter) (F) Outside Diameter (Reference)
13、3.380 1.84 6.56 1.762 15, 20, 22, 24 E .635 3.620 1.59 6.56 1.762 15, 20, 22, 24 E 0.635 4.000 1.21 6.56 1.762 15, 20, 22, 24 E 0.635 3.620 1.84 6.81 1.762 20, 22, 24 E .635 4.000 1.46 6.81 1.762 20, 22, 24 E 0.635 4.250 1.21 6.81 1.762 20, 22, 24 E 0.635 3.620 1.59 6.81 2.000 20,24 E .719 4.000 1.2
14、1 6.81 2.000 20,24 E .719 TABLE 2 - DIMENSIONS FOR DOUBLE CLAMPS (DUAL MOUNTING), REFER TO FIGURE 3 (A) Spacer Width +0.060 0.047 (B) Rim Clamp Toe Length 0.05 (C) Spoke Length 0.06 (D) Rim Bevel Intersection (28 degrees Layout Line) 0.040 (E) 28 degrees Bevel Layout Diameter (Nominal Wheel Diameter
15、) (G) Rim Clamp Diameter 0.03 (H) Hole Spread 0.01 (J) Rim Clamp Height 0.03 (F) Outside Diameter (Reference) 4.000 1.21 6.56 1.762 15 13.54 4.50 1.82 E .635 4.000 1.21 6.56 1.762 20 18.54 6.81 2.42 E .635 4.000 1.21 6.56 1.762 22 20.54 8.91 2.42 E .635 3.380 1.84 6.56 1.762 15 13.54 4.50 1.82 E .63
16、5 3.380 1.84 6.56 1.762 20 18.54 6.81 2.42 E .635 3.380 1.84 6.56 1.762 22 20.54 8.91 2.42 E .635 SAE J1835 Revised JAN2014 Page 4 of 7 4.3.1.2 Single Clamps FIGURE 4 - SINGLE CLAMPS 4.3.1.3 Double Clamps FIGURE 5 - DOUBLE CLAMPS SAE J1835 Revised JAN2014 Page 5 of 7 4.3.2 Single Mounting 4.3.2.1 Si
17、ngle Assembly FIGURE 6 - SINGLE ASSEMBLY, DROP CENTER RIM SHOWN TABLE 3 - DIMENSIONS FOR SINGLE CLAMPS (SINGLE MOUNTING), REFER TO FIGURE 6 (E) 28 degrees Bevel Layout Diameter (Nominal Wheel Diameter) (D) Rim Bevel Intersection (28 degrees Layout Line 0.040) (K) Rim Clamp Offset 0.03 (L) Bevel Leng
18、th 0.06 (F) Outside Diameter (Reference) 20 1.762 0.46 0.60 E .635 22 1.762 0.46 0.60 E .635 24 1.762 0.46 0.60 E 0.635 20 2.000 0.63 0.60 E .719 24 2.000 0.63 0.60 E .719 4.3.2.2 Single Clamps FIGURE 7 - SINGLE CLAMPS SAE J1835 Revised JAN2014 Page 6 of 7 5. SECTION 2 - MOUNTING HARDWARE DIMENSIONS
19、 (CURRENT PRACTICE) 5.1 Single Clamps FIGURE 8 - SINGLE CLAMPS TABLE 4 - DIMENSION FOR SINGLE CLAMPS (DUAL MOUNTING), REFER TO FIGURE 8 (A) Spacer Width +0.060 0.047 (B) Rim Clamp Toe Length 0.13 (C) Spoke Length 0.06 (E) 28 degrees Bevel Layout Diameter (Nominal Wheel Diameter) (D) Rim Bevel Inters
20、ection (28 degrees Layout Line) 0.040 (F) Outside Diameter (Reference) 3.380 1.86 6.56 15, 20, 22, 24 1.762 E 0.635 3.620 1.56 6.56 15, 20, 22, 24 1.762 E 0.635 4.000 1.25 6.56 15, 20, 22, 24 1.762 E 0.635 3.620 1.82 6.81 20, 22, 24 1.762 E 0.635 4.000 1.48 6.81 20, 22, 24 1.762 E 0.635 3.620 1.59 6
21、81 20, 24 2.000 E 0.719 4.000 1.21 6.81 20, 24 2.000 E 0.719 3.380 2.30 6.94 20, 22, 24 1.762 E 0.635 3.620 2.05 6.94 20, 22, 24 1.762 E 0.635 4.000 1.67 6.94 20, 22, 24 1.762 E 0.635 4.250 1.42 6.94 20, 22, 24 1.762 E 0.635 3.620 2.03 7.03 20, 22, 24 1.762 E 0.635 4.000 1.72 7.03 20, 22, 24 1.762
22、E 0.635 4.250 1.47 7.03 20, 22, 24 1.762 E 0.635 4.500 1.22 7.03 20, 22, 24 1.762 E 0.635 3.380 2.36 7.06 20, 22, 24 1.762 E 0.635 3.620 2.06 7.06 20, 22, 24 1.762 E 0.635 4.000 1.75 7.06 20, 22, 24 1.762 E 0.635 4.250 1.50 7.06 20, 22, 24 1.762 E 0.635 4.500 1.25 7.06 20, 22, 24 1.762 E 0.635 SAE J
23、1835 Revised JAN2014 Page 7 of 7 6. NOTES 6.1 Marginal Indicia A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the do
24、cument title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. PREPARED BY THE SAE TRUCK AND BUS WHEEL COMMITTEE OF THE SAE TRUCK AND BUS BRAKE AND STABILITY CONTROL STEERING COMMITTEE
