1、 METRIC AEROSPACE STANDARD (R) FITTING END, 24 CONE, DESIGN STANDARD, METRIC MA2095 Copyright 2004 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, rec
2、ording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: custsvcsae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1985-10REAFFIRMED 2001-12REVISED 2004-08 THIRD ANG
3、LE PROJECTION CUSTODIAN: SAE G-3/G-3B REV. C FEDERAL SUPPLY CLASS4730 MA2095 SHEET 1 OF 3 REV.C PROCUREMENT SPECIFICATION: NONE /2/SAE TechnicalStandards Board Rules provide that: “This report is published by SAE toadvance thestate of technical andengineering sciences. Theuse of thisreport is entire
4、ly voluntary, andits applicabilityandsuitability forany particularuse,including any patent infringement arising therefrom, is thesole responsibility oftheuser.” SAE reviews each technical report at least every five yearsat which time it may be reaffirmed, revised, orcancelled.SAE invites yourwritten
5、 commentsandsuggestions. FIGURE 1 - FITTING END DESIGN, STYLE G FIGURE 2 - FITTING END DESIGN, STYLE E SAME AS STYLE G EXCEPT AS SHOWN Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-METRIC AEROSPACE
6、 STANDARD (R) FITTING END, 24 CONE, DESIGN STANDARD, METRIC MA2095 REV. C MA2095 SHEET 2 OF 3 REV.C TABLE 1 - DIMENSIONS BASIC NO. MA2095 /11/ SIZE CODE (NOMINAL TUBE SIZE DN) /1/ T THREAD PER MA1370 (ISO 5855-3) 4g6g B 0 0.5 C D E 05 5 MJ 10 X 1 8.6 4.3 8.5 6.5 06 6 MJ 12 X 1.25 10.2 5.3 10.1 7.5 0
7、8 8 MJ 14 X 1.5 11.9 7.1 11.8 9.5 10 10 MJ 16 X 1.5 13.9 9.1 13.8 11.5 12 12 MJ 18 X 1.5 15.9 10.9 15.8 13.5 14 14 MJ 20 X 1.5 17.9 12.5 17.8 15.5 16 16 MJ 22 X 1.5 19.9 14.5 19.8 17.5 20 20 MJ 27 X 1.5 24.9 18.1 24.8 21.5 25 25 MJ 33 X 1.5 30.9 22.5 30.8 26.6 32 32 MJ 42 X 2 39.3 29.3 39.2 33.7 40
8、40 MJ 50 X 2 47.3 37.3 47.2 41.7 TABLE 1A - DIMENSIONS BASIC NO. MA2095 /11/ SIZE CODE G 0.05 L 0.2 M 0.2 R S 0.10 U V Z 0.12 AA 0.076 05 5.31 2.2 9.0 0.7 0.40 0.13 0.13-0.25 4.30 5.80 06 6.31 2.7 10.0 0.9 0.50 0.13 0.25-0.40 4.80 6.30 08 8.31 3.2 11.0 1.0 0.55 0.25 0.25-0.40 4.80 6.30 10 10.31 3.2
9、12.0 1.0 0.55 0.25 0.25-0.40 4.80 6.30 12 12.31 3.2 12.0 1.0 0.55 0.25 0.25-0.40 4.90 7.30 14 14.31 3.2 12.0 1.0 0.55 0.25 0.25-0.40 4.90 7.30 16 16.31 3.2 12.0 1.0 0.55 0.25 0.25-0.40 4.90 7.30 20 20.33 3.2 12.0 1.0 0.55 0.25 0.25-0.40 4.90 7.30 25 25.33 3.2 13.0 1.0 0.55 0.40 0.50-0.70 4.90 7.30 3
10、2 32.35 4.2 14.0 1.3 0.70 0.40 0.50-0.70 5.40 7.80 40 40.35 4.2 14.0 1.3 0.70 0.40 0.50-0.70 5.40 7.80 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-METRIC AEROSPACE STANDARD (R) FITTING END, 24 CO
11、NE, DESIGN STANDARD, METRIC MA2095 REV. C MA2095 SHEET 3 OF 3 REV.C NOTES: /1/ DN = NOMINAL TUBE OUTSIDE DIAMETER. /2/ THIS FITTING END IS INTENDED FOR USE WITH 24 CONE FITTINGS PER MA2005 (ISO 7169). 3. THREAD GAGING SHALL BE PER MA1566. 4. INTERPRETATION OF DRAWING PER MAP4296. 5. THE CHANGE BAR (
12、 l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. 6. INVENTORIED
13、PARTS WITH FITTING ENDS CONFORMING ONLY TO THE PREVIOUS REVISION “A“ OF THIS STANDARD MAY BE USED TO DEPLETION. FITTING ENDS CONFORMING TO PREVIOUS REVISION “N/C“ OR “B“ MUST NOT BE USED. 7. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED
14、SURFACES TO BE 3.2 m Ra. 8. BREAK EDGES PER 0.07 MAXIMUM UNLESS OTHERWISE SPECIFIED. 9. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 10. DIMENSIONS IN MILLIMETERS. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS 0.1, ANGULAR DIMENSIONS 030. /11/ EXAMPLE OF DRAWING CALLOUT: a. TABULATED PART DRAWING: FITTING END PER MA2095 b. INDIVIDUAL PART DRAWING: Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
