1、 AEROSPACE STANDARD FITTING ASSEMBLY, ADAPTER RING LOCKED PORTCONNECTION TO 830 BEAM SEAL 28,000 KPA, METRIC MA2111Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic
2、, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1985-02R
3、EVISED 2006-06 REAFFIRMED 2015-04THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B /5/ REV.C FEDERAL SUPPLY CLASS 4730MA2111 SHEET 1 OF 3 REV. C PROCUREMENT SPECIFICATION: /4/ MA2500 (ISO 7169)SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicala
4、ndengineering sciences. Theuse ofthisreport is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised
5、,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/MA2111C RATIONALE MA2111C HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. I
6、DENTIFICATION LOCATION OPTIONAL /8/ ( ) ( ) ( ) BASIC NO. MA2111 /17/ SIZE CODE (NOMINAL TUBE SIZE) A THREAD PER MA1370 B THREAD PER MA1370 C 0.09D REF E +0.20/0 F +0.15/-0.05G MIN 05 5.0 MJ10 x 1-4g6g MJ6 x 1-4h6h 12.90 4.20- 4.40 2.50 4.50 7.1006 6.0 MJ12 x 1.25-4g6g MJ8 x 1-4h6h 14.75 5.00- 5.20
7、4.40 6.50 9.0508 8.0 MJ14 x 1.5-4g6g MJ10 x 1-4h6h 17.80 6.70- 6.90 6.10 8.50 11.0610 10.0 MJ16 x 1.5-4g6g MJ12 x 1.25-4h6h 19.50 8.70- 8.90 7.70 10.20 12.7812 12.0 MJ18 x 1.5-4g6g MJ14 x 1.5-4h6h 21.00 10.60-10.80 9.00 11.90 14.3814 14.0 MJ20 x 1.5-4g6g MJ16 x 1.5-4h6h 22.60 11.45-11.65 10.70 13.90
8、 16.3616 16.0 MJ22 x 1.5-4g6g MJ18 x 1.5-4h6h 26.40 13.30-13.60 12.50 15.90 18.3718 18.0 MJ24 x 1.5-4g6g MJ20 x 1.5-4h6h 28.00 15.30-15.60 14.20 17.90 20.3720 20.0 MJ27 x 1.5-4g6g MJ22 x 1.5-4h6h 30.20 18.00-18.30 15.90 19.90 22.3822 22.0 MJ30 x 1.5-4g6g MJ24 x 1.5-4h6h 33.70 20.80-21.10 17.65 21.90
9、 24.3525 25.0 MJ33 x 1.5-4g6g MJ27 x 1.5-4h6h 37.00 22.40-22.70 20.20 24.90 27.3528 28.0 MJ36 x 1.5-4g6g MJ30 x 1.5-4h6h 40.95 25.60-25.90 22.80 27.90 30.3732 32.0 MJ39 x 1.5-4g6g MJ33 x 1.5-4h6h 43.00 28.30-28.60 25.40 30.90 33.37FIGURE 1 - ADAPTER, ASSEMBLY TABLE 1 - DIMENSIONS TABLE 1A - A THROUG
10、H G AEROSPACE STANDARD MA2111 SHEET 2 OF 3 REV. C FITTING ASSEMBLY, ADAPTER RING LOCKED PORT CONNECTION TO 830 BEAM SEAL 28,000 KPA, METRIC TABLE 1B - H THROUGH N AND WEIGHTS BASIC NO. MA2111 /17/ SIZE CODE H REF J 0.20K +0.50/0L +0.15/-0.10M 0.4N 0.2WEIGHT KG/EA MAX 05 9.37 16.35 7.95 3.00 11.0 5.3
11、 0.007 06 11.53 18.85 8.60 3.00 13.0 6.1 0.009 08 13.87 21.60 9.30 3.00 15.0 7.0 0.015 10 15.37 21.60 10.00 3.00 15.0 7.0 0.018 12 17.12 21.65 10.65 3.00 15.0 7.0 0.022 14 18.77 21.85 11.30 3.00 15.0 7.0 0.026 16 20.93 21.85 12.00 3.00 15.0 7.0 0.033 18 23.85 22.65 12.70 3.00 15.0 7.0 0.038 20 24.92
12、 23.25 13.35 3.00 15.5 7.0 0.044 22 27.41 23.25 14.00 3.00 15.5 7.0 0.050 25 31.47 23.65 15.05 3.00 15.5 7.0 0.065 28 33.60 23.65 16.05 3.00 15.5 7.0 0.077 32 37.57 23.65 17.05 3.00 15.5 7.0 0.086 NOTES: 1. MATERIAL: a. FITTING: 6AL-4V TITANIUM ALLOY PER AMS 4928, AMS 4965, OR AMS 4967. b. LOCKRING:
13、 A286 CORROSION RESISTANT STEEL PER AMS 5731, AMS 5732, AMS 5734 OR AMS 5737. 2. HEAT TREATMENT: a. FITTING: 900 MPa UTS MIN b. LOCKRING: 34-40 HRC 3. FINISH: a. FITTING: ANODIC TREATMENT PER AMS 2488 TYPE 2 ON ALL SURFACES AND SOLID FILM LUBE PER AS5272, TYPE I ON ALL SURFACES EXCEPT IN THE FLOW HO
14、LE. ALTERNATE FINISH: SOLID FILM LUBE PER AS5272, TYPE I ON ALL SURFACES EXCEPT IN THE FLOW HOLE. b. LOCKRING: PASSIVATE PER AMS 2700. /4/ PROCUREMENT SPECIFICATION: MA2005 (ISO 7169) EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AND ACCREDITED
15、 MANUFACTURER LISTED IN PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED MANUFACTURER LIST (QML) FOR THIS TYPE PRODUCT. THE QML IS AVAILABLE AT . /5/ AECMA INTEREST: FUTURE REVISIONS TO THIS STANDARD SHALL BE COORDINATED WITH AECMA C4 COMMITTEE. AECMA IS ASSOCIATION EUROPEENNE DES CONSTRUCTEURS DE MATER
16、IEL AEROSPATIAL (PARIS, FRANCE). /6/ SEALING SURFACE: NO VISIBLE DEFECTS. TO BE PROTECTED FOR SHIPMENT. /7/ LOCKRING RETAINED ON FITTING BY CONTROLLED INTERFERENCE FIT. LOCKRING EXTERNAL SERRATION DELETED ONE TOOTH FOR METRIC IDENTIFICATION PURPOSE. AEROSPACE STANDARD MA2111 SHEET 3 OF 3 REV. C FITT
17、ING ASSEMBLY, ADAPTER RING LOCKED PORT CONNECTION TO 830 BEAM SEAL 28,000 KPA, METRIC /8/ IDENTIFICATION: a. MARK AT LOCATION(S) SHOWN PER AS478 METHOD 2 OR 15, MANUFACTURERS NAME, TRADEMARK, OR CAGE CODE. b. MARK PER AS478 CLASS 35D, MANUFACTURERS NAME, TRADEMARK OR CAGE CODE AND PART NUMBER. 9. WO
18、RKING PRESSURE: THIS PART IS DESIGNED FOR USE IN 28 000 kPa WORKING PRESSURE SYSTEMS COMPATIBLE WITH TITANIUM. 10. ADAPTERS TO BE INSTALLED PER MA2114 INTO BOSS CAVITIES PER MA2110. 11. INVENTORIED PARTS CONFORMING TO THE PREVIOUS “LETTER CHANGE” MAY BE USED TO DEPLETION. 12. INTERPRETATION OF DRAWI
19、NG PER MAP4296. 13. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 3.2 m Ra AND SEALING SURFACE TO BE 1.6 m Ra. 14. BREAK EDGES 0.08 TO 0.38 UNLESS OTHERWISE SPECIFIED. 15. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 16
20、. DIMENSIONS IN MILLIMETERS. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS 0.13, ANGULAR DIMENSIONS 5. /17/ EXAMPLE OF PART NUMBER: 18. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT.
