1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA
2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any
3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-19239-6 SANS 1129:2008Edition 1.4Any reference to SABS 1129 is deemedto be a reference to this standard(Government Notice No. 1373 of 8 No
4、vember 2002)SOUTH AFRICAN NATIONAL STANDARD Steel door frames Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 1129:2008 Edition 1.4 Table of changes Change No. Date Scope Amdt 1 1983 Sc
5、ope not available. Amdt 2 1998 Amended to add an optional dimension to door frame profiles. Amdt 3 2002 Amended to include the dimensions for hinges, to alter the thicknesses for double rebate door frames for half-brick walls and to update applicable standards. Amdt 4 2008 Amended to change the desi
6、gnation of SABS standards to SANS standards, and to update referenced standards. Acknowledgement The SABS Standards Division wishes to acknowledge the valuable assistance derived from the British Standards Institution. Foreword This South African standard was approved by National Committee SABS TC 1
7、077, Engineering materials Ferrous metals, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This document was published in December 2008. This document supersedes SABS 1129:2002 (edition 1.3). A vertical line in the margin shows where
8、 the text has been technically modified by amendment No. 4. SANS 1129:2008 Edition 1.4 1 Contents Page Acknowledgement Foreword 1 Scope . 3 2 Definitions 3 3 Requirements . 4 4 Packing and marking . 10 5 Sampling and compliance with the specification . 10 6 Inspection . 11 6.1 Inspection. 11 6.2 Squ
9、areness 11 6.3 Straightness . 11 Figures 1-7 11-17 Appendix A Applicable standards . 18 Appendix B Notes to purchasers. 19 Appendix C Notes on fixing and subsequent painting of steel door frames 20 SANS 1129:2008 Edition 1.4 2 This page is intentionally left blank SANS 1129:2008 Edition 1.4 3 Steel
10、door frames 1 Scope 1.1 This specification covers steel door frames (with or without fanlight frames) for walk-through doors. NOTE a) The standards referred to in the specification are listed in appendix A. b) Requirements that must be specified by the purchaser are listed in appendix B. c) Notes on
11、 the fixing of a door frame and its subsequent painting are given in appendix C. 2 Definitions 2.1 For the purposes of this specification the following definitions shall apply: acceptable acceptable to the authority administering this standard, or to the parties concluding the purchase contract, as
12、relevant Amdt 3 co-ordinating dimension a dimension of a component that determines the co-ordination of one component with another and with the spaces in buildings and in which allowances for positional and manufacturing tolerances are included defective a door frame that fails in one or more respec
13、ts to comply with the relevant requirements of the specification door frame a frame that incorporates or does not incorporate (as relevant) a fanlight frame (see figures 2 and 3) functional height of a non-modular door frame the vertical distance between the finished floor height and the inside surf
14、ace of the rebate in the head member, i.e. the rebate height less 22 mm left-hand door a single leaf door that is such that, when the door opens towards the observer, the hinges are on the left-hand rebate of the door frame as seen by the observer (see figure 5) SANS 1129:2008 Edition 1.4 4 lot not
15、less than 10 and not more than 150 assembled door frames of the same type, materials, dimensions, construction, and (when relevant) handing, from one manufacturer, submitted at any one time for inspection rebate height the vertical distance between the lower end of the jambs and the inside surface o
16、f the rebate in the head member (see figures 1, 2 and 3) NOTE The rebate height includes the “building-in” dimension. rebate width the horizontal distance between the inside surfaces of the rebates of a) in the case of door frames for single leaf doors, the hinge jamb and lock jamb; and b) in the ca
17、se of door frames for double leaf doors, the two hinge jambs (see figures 1 and 2) right-hand door a single leaf door that is such that, when the door opens towards the observer, the hinges are on the right-hand rebate of the door frame as seen by the observer (see figure 5) size designation: modula
18、r steel door frames the combination of the co-ordinating nominal width and height, in millimetres (e.g. 900 2 400) non-modular steel door frames the combination of the rebate width and the nominal functional height, in millimetres (e.g. 813 2 032) 3 Requirements 3.1 Type Door frames shall be of one
19、of the following types, as specified by the purchaser: a) Type 1A. Single leaf doors without fanlight. b) Type 1B. Single leaf doors with fanlight. c) Type 2A. Double leaf doors without fanlight. d) Type 2B. Double leaf doors with fanlight. 3.2 Materials All materials shall be of acceptable quality.
20、 The material of the components shall be as follows: a) Door frames, base ties, and fixing lugs. Mild steel. b) Lock strike plates. Mild steel, an 18/8 (AISI Type 304) stainless steel, an aluminium alloy, or, if so specified by the purchaser, brass. SANS 1129:2008 Edition 1.4 5 c) Shock absorbers. R
21、ubber or other acceptable material. d) Hinges. Steel or brass, as specified by the purchaser. 3.3 Dimensions, squareness and straightness 3.3.1 Rebate height and width The rebate height and rebate width of door frames shall conform to the values given in table 1 or table 1A, appropriate to the size
22、designation. Table 1 Heights and widths: Modular door frames 1 2 3 4 5 6 7 Type No. Height Co-ordinating nominal width mm mm 700 800 900 1 300 1 700 Rebate width mm* Co-ordinating nominal dimension Rebate* 616 716 816 1 216 1 616 2 100 2 080 1A 1A 1A 2A 2A 2 400 2 380 1B 1B 1B 2B 2B 2 600 2 580 1B 1
23、B 1B 2B 2B * Subject to a tolerance of 12+mm. Table 1A Heights and widths*: Non-modular door frames 1 2 3 Height mm Rebate width Functional Rebate mm 1 981 2 003 762 2 032 2 054 686, 762, 813, 1 359, 1 511, or 1 613 * All dimensions are subject to a tolerance of 12+mm. 3.3.2 Fanlight height In door
24、frames of types 1B and 2B the vertical distance between the inside surfaces of the upper rebate in the transom and the rebate in the head member shall, subject to a tolerance of 12+mm, be as follows: a) Door frames of co-ordinating height 2 400 mm: 268 mm. b) Door frames of co-ordinating height 2 60
25、0 mm: 468 mm. c) Non-modular door frames: 305 mm. SANS 1129:2008 Edition 1.4 6 3.3.3 Cross-section profile and dimensions The profile and dimensions of the cross-section of the jambs and head members of door frames shall be as given in figures 4(a), 4(b), 4(c), and 4(d) appropriate to the type of pr
26、ofile (i.e. with a single or a double rebate) and the type of wall (i.e. half brick or one brick) specified by the purchaser. The profile and dimensions of the cross-section of transoms for frames of types 1B and 2B shall be as given in figure 4(e). 3.3.4 Hinges The dimensions of hinges shall confor
27、m to the values given below. Amdt 3 a) Steel hinges (see table 2) Amdt 3 1) On hinge jambs: type No. 1A/308. 2) On transoms or head members, as relevant: type No. 1A/306. b) Brass hinges (see table 3) Amdt 3 1) On hinge jambs: type No. 1A/2105. 2) On transoms or head members, as relevant: type No. 1
28、A/2104. Table 2 Dimensions and weights of narrow steel butt hinges Amdt 3 (Third angle projection) Narrow steel butt hinge with riveted pin Narrow steel butt hinge with loose headed pin 1 2 3 4 5 6 7 8 Length of joint Open width over flaps Diameterof pin Material thicknessA B C D Weight per gross pa
29、irs mm mm mm Holes countersunk for screw gauge No. kg BS type reference No. mm Min. Max. Min. Min. min. Number of screw holes in each hinge Min. 1A/306 76,2 + 0,19 0,51 48,4 50,8 4,19 1,63 7 6 19,05 1A/308 101,6 + 0,19 0,66 70,0 73,0 5,89 1,91 8 8 43,55 Amdt 3SANS 1129:2008 Edition 1.4 7 Table 3 Dim
30、ensions and weights of brass butt hinges Amdt 3 Third angle projection 1 2 3 4 5 6 7 8 Length of joint Width when open Diameter of pin Material thicknessA B C D Weight per dozen pairs mm mm Holes countersunkfor screw gauge No. kg BS type reference No. mm mm Min. Min. min. Number of screw holes in ea
31、ch hinge Min. 1A/2104 76,2 41,3 3,10 2,03 8 6 1,59 1A/2105 101,6 60,3 3,91 2,70 10 8 4,25 Amdt 33.3.5 Squareness Any out-of-squareness measured in accordance with 6.2, shall not exceed 2,0 mm per metre of the average length of the diagonals. 3.3.6 Straightness Any concavity or convexity of a member
32、of a door frame, determined in accordance with 6.3, shall not exceed 1,5 mm per metre of length of the member. 3.4 Construction 3.4.1 Door frames a) Door frames shall be made of pressed or roll-formed sheet. Jambs and head members shall have a nominal thickness of, in the case of double rebate profi
33、les for one brick wall (i.e. 230 mm width), at least 1,20 mm and in the case of single rebate profiles for one brick wall, at least 1,60 mm. Amdt 3 SANS 1129:2008 Edition 1.4 8 For half brick walls of thickness ranging from 90 mm to 150 mm (width), single rebate profiles shall be of thickness at lea
34、st 1,20 mm and double rebate profiles shall be of thickness 1,0 mm. Amdt 3 Transoms shall have nominal thicknesses equal to the thicknesses specified for each door jamb as indicated above. Amdt 3 b) Base ties shall be of equal angle section with a leg length of 16 1 mm. They shall be so located that
35、 the bottom of the legs is flush with the lower ends of the jambs (see figure 2). c) Fanlight frames shall be suitable for fixed or opening type fanlights, as specified by the purchaser. In the case of opening type fanlights the fanlight shall be bottom or top hung, as specified by the purchaser (se
36、e figures 3 and 6), and holes, of the size, and located as specified by the purchaser, shall be provided for the attachment of an opening device. In the case of fixed type fanlights, and if so specified by the purchaser, acceptable means for fixing the glazing in position shall be provided. 3.4.2 Fi
37、ttings a) Fixing lugs. Each jamb shall be provided with, in the cases of types 1A and 2A door frames, at least three, and in the cases of types 1B and 2B door frames, at least four fixing lugs. Fixing lugs shall have a nominal thickness and a nominal width of at least 1,20 mm and 25 mm respectively,
38、 and a length such as to have an outstand of at least 150 mm (see figures 2 and 3). Fixing lugs shall be welded centrally to the well of the profiles or, if so specified by the purchaser, shall be supplied loose and shall have an acceptable cross-member (head) for locating the lug between the inner
39、faces of the sides of the profile of each jamb. b) Hinges. Each hinge jamb of a door frame and each transom or head member (as relevant) of a frame for an opening type fanlight shall be fitted with two or (if so specified by the purchaser) more butt hinges. The distances between the transverse centr
40、e-lines of the uppermost and lowest hinges on a hinge jamb and the inside surface of the head member or the transom (as relevant) shall be 200 1 mm and 1 800 1 mm respectively (see figure 2) and, when relevant, additional hinges shall be so positioned that they are equidistant from each other. In th
41、e cases of door frames of types 1A and 1B the hinge jamb shall be suitable for a right-hand door or a left-hand door, as specified by the purchaser (see figure 5). Steel hinges shall be welded or screwed to the door frames (as specified by the purchaser) and brass hinges shall be screwed to the door
42、 frames (see figures 5 and 6). In the case of hinges that are screwed, each hinge shall be screwed to a mild steel reinforcing plate of nominal thickness at least 2,0 mm and of width and length greater than those of the leaf of the hinge. The leaf of each hinge that is attached by welding and each r
43、einforcing plate for hinges attached by screws shall be securely welded to the back surface of the hinge jamb, transom, or head member, as relevant. c) Lock strike plates. The lock jamb of each door frame of type 1A or 1B shall be fitted with an adjustable lock strike plate of nominal thickness at l
44、east 1,20 mm, and suitable for a lock or a latch that complies with the requirements of SANS 4 for the type of lock/latch specified by the purchaser. The lock strike plate shall be screwed in position and shall be capable of being adjusted through a horizontal distance of at least 5 mm. The vertical
45、 distance between the transverse centre-line of the lock strike plate and the lower end of the jamb shall be not less than 1 150 mm and not more than 1 200 mm (see figure 2). SANS 1129:2008 Edition 1.4 9 d) Shock absorbers. Each lock jamb of door frames of types 1A and 1B shall have two shock absorb
46、ers, inserted in holes in the 12 mm wide face of the rebate and positioned at approximately the same level as the midpoints of the uppermost and lowest hinges (see figure 2). 3.5 Welded joints The welding of all welded joints shall be such that it is acceptable. The profiles of the welds shall merge
47、 smoothly into the adjacent surfaces of the parent metal without excessive undercut or overlap. The weld faces shall be reasonably uniform and free from excessive porosity, cavities, and trapped slag and, in the case of surfaces that will be exposed in service, shall have been finished flush with th
48、e parent metal. In butt welds there shall be adequate root penetration. All weld metal, heat affected zones, and the adjacent parent metal shall be free from cracks. 3.6 Finish of steel surfaces NOTE Fittings of a material other than mild steel need not have a coating of any type. 3.6.1 General The
49、surfaces of all components of door frames and fittings (other than lock strike plates) that are made of mild steel shall have a painted, galvanized, or sprayed zinc or aluminium coating that complies with the requirements given in 3.6.2-3.6.4 relevant to the type of coating specified by the purchaser. All surfaces shall, before coating, be clean and free from weld spatter, loose scale, flux, grease, oil, and other foreign matter. In the case of stainless steel lock strike plates, the exposed surfaces shall have a bright polished or a matt finish, as specified by
