1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA
2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any
3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-23556-7 SANS 20474-5:2010Edition 1ISO 20474-5:2008Edition 1SOUTH AFRICAN NATIONAL STANDARD Earth-moving machinery Safety Part 5: Requireme
4、nts for hydraulic excavators This national standard is the identical implementation of ISO 20474-5:2008, and is adopted with the permission of the International Organization for Standardization. Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001Tel: +27
5、12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 20474-5:2010 Edition 1 ISO 20474-5:2008 Edition 1 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee SABS TC 1034, Agricultural, earth-moving, forestry and construction equi
6、pment and machinery, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in January 2010. Reference numberISO 20474-5:2008(E)ISO 2008INTERNATIONAL STANDARD ISO20474-5First edition2008-12-15Earth-moving ma
7、chinery Safety Part 5: Requirements for hydraulic excavators Engins de terrassement Scurit Partie 5: Exigences applicables aux pelles hydrauliques SANS 20474-5:2010This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 20474-5:2008(E) PDF discla
8、imer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties ac
9、cept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the
10、 file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTEC
11、TED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs mem
12、ber body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2008 All rights reservedSANS 20474-5:2010This s tandard may only be used and printed b
13、y approved subscription and freemailing clients of the SABS .ISO 20474-5:2008(E) ISO 2008 All rights reserved iiiContents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references . 1 3 Terms and definitions. 2 4 Safety requirements and/or protective measures . 3 4.1 General. 3 4.2 Access .
14、 3 4.3 Operators station . 3 4.4 Controls for driving and steering 4 4.5 Swing brakes. 4 4.6 Stability and safety devices. 4 4.7 Parking brake for compact crawler excavators. 5 4.8 Specific requirements for walking excavators 5 5 Verification of safety requirements and/or protective measures 9 6 Inf
15、ormation for use . 9 Annex A (informative) Illustrations. 10 Bibliography . 12 SANS 20474-5:2010This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 20474-5:2008(E) iv ISO 2008 All rights reservedForeword ISO (the International Organization fo
16、r Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the
17、 right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Internati
18、onal Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication
19、as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
20、ISO 20474-5 was prepared by Technical Committee ISO/TC 127, Earth-moving machinery, Subcommittee SC 2, Safety, ergonomics and general requirements. ISO 20474 consists of the following parts, under the general title Earth-moving machinery Safety: Part 1: General requirements Part 2: Requirements for
21、tractor-dozers Part 3: Requirements for loaders Part 4: Requirements for backhoe loaders Part 5: Requirements for hydraulic excavators Part 6: Requirements for dumpers Part 7: Requirements for scrapers Part 8: Requirements for graders Part 9: Requirements for pipelayers Part 10: Requirements for tre
22、nchers Part 11: Requirements for earth and landfill compactors Part 12: Requirements for cable excavators Part 13: Requirements for rollers Part 14: Information on national and regional provisions Technical Specification SANS 20474-5:2010This s tandard may only be used and printed by approved subscr
23、iption and freemailing clients of the SABS .ISO 20474-5:2008(E) ISO 2008 All rights reserved vIntroduction This document is a type-C standard as stated in ISO 12100. The machinery concerned and the extent to which hazards, hazardous situations or hazardous events are covered are indicated in the Sco
24、pe of this document. When requirements of this type-C standard are different from those stated in type-A or B standards, the requirements of this type-C standard take precedence over the requirements of the other standards for machines that have been designed and built according to the requirements
25、of this type-C standard. Provisions that are applicable for Australia, the EU, Japan or the USA, and which are mandatory for compliance with specific governmental laws, directives or regulations in force in the particular country or region, are given in ISO/TS 20474-14. NOTE Other countries or regio
26、ns may also have regional requirements. SANS 20474-5:2010This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .SANS 20474-5:2010This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .INTERNATIONAL
27、STANDARD ISO 20474-5:2008(E) ISO 2008 All rights reserved 1Earth-moving machinery Safety Part 5: Requirements for hydraulic excavators 1 Scope This part of ISO 20474 gives the safety requirements specific to hydraulic excavators as defined in ISO 6165. It is intended to be used in conjunction with I
28、SO 20474-1, which specifies general safety requirements common to earth-moving machine families, and with ISO/TS 20474-14, which gives information on provisions that are mandatory in particular countries or regions. The specific requirements given in this part of ISO 20474 take precedence over the g
29、eneral requirements of ISO 20474-1. This part of ISO 20474 deals with all significant hazards, hazardous situations and events relevant to the earth-moving machinery within its Scope when used as intended or under conditions of misuse reasonably foreseeable by the manufacturer (see also ISO/TS 20474
30、-14). It specifies the appropriate technical measures for eliminating or reducing risks arising from significant hazards, hazardous situations or events during commissioning, operation and maintenance. It is not applicable to machines manufactured before the date of its publication. 2 Normative refe
31、rences The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3449:2005, Earth-moving machinery Fall
32、ing-object protective structures Laboratory tests and performance requirements ISO 3471, Earth-moving machinery Roll-over protective structures Laboratory tests and performance requirements ISO 6016, Earth-moving machinery Methods of measuring the masses of whole machines, their equipment and compon
33、ents ISO 6165, Earth-moving machinery Basic types Identification and terms and definitions ISO 6683, Earth-moving machinery Seat belts and seat belt anchorages Performance requirements and tests ISO 7135, Earth-moving machinery Hydraulic excavators Terminology and commercial specifications ISO 7451,
34、 Earth-moving machinery Volumetric ratings for hoe-type and grab-type buckets of hydraulic excavators and backhoe loaders ISO 7546, Earth-moving machinery Loader and front loading excavator buckets Volumetric ratings SANS 20474-5:2010This s tandard may only be used and printed by approved subscripti
35、on and freemailing clients of the SABS .ISO 20474-5:2008(E) 2 ISO 2008 All rights reservedISO 8084, Machinery for forestry Operator protective structures Laboratory tests and performance requirements ISO 10262, Earth-moving machinery Hydraulic excavators Laboratory tests and performance requirements
36、 for operator protective guards ISO 10567:2007, Earth-moving machinery Hydraulic excavators Lift capacity ISO 12117, Earth-moving machinery Tip-over protection structure (TOPS) for compact excavators Laboratory tests and performance requirements ISO 20474-1:2008, Earth-moving machinery Safety Part 1
37、: General requirements 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 20474-1 and ISO 7135, and the following, apply. 3.1 hydraulic excavator self-propelled machine on crawlers, wheels or legs, having an upper structure normally capable of a 360 swi
38、ng with mounted equipment, primarily designed for excavating with bucket, without moving the undercarriage during the work cycle NOTE 1 An excavator work cycle normally comprises excavating, elevating, swinging and discharging of material (see ISO 6165). NOTE 2 Hydraulic excavators may also be used
39、for material handling/transportation. 3.1.1 minimal swing radius excavator MSRX excavator for operation in confined space having an upper structure with a short swing radius (equipment and attachment swing within 120 % of the width of the undercarriage) 3.1.2 compact excavator excavator and minimal
40、swing radius excavator (3.1.1) with an operating mass in accordance with ISO 6016 of less than or equal to 6 000 kg 3.2 walking excavator excavator with three or more supporting legs which may be articulated, telescopic or both and which can be fitted with wheels NOTE For information on regional pro
41、visions, see ISO/TS 20474-14. SANS 20474-5:2010This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 20474-5:2008(E) ISO 2008 All rights reserved 34 Safety requirements and/or protective measures 4.1 General Hydraulic excavators shall comply wi
42、th the safety requirements and/or protective measures of ISO 20474-1, in as far as those are not modified by the specific requirements of this clause. 4.2 Access ISO 20474-1:2008, 4.2, shall apply. 4.3 Operators station 4.3.1 Minimum space envelope ISO 20474-1:2008, 4.3.1.2, shall apply. For mandato
43、ry national and/or regional provisions, see ISO/TS 20474-14. 4.3.2 Operators protection 4.3.2.1 Operators protective guard For mandatory national and/or regional provisions, see ISO/TS 20474-14. 4.3.2.2 Roll over protective structures (ROPS) and tip-over protective structures (TOPS) ISO 20474-1:2008
44、, 4.3.3, shall apply only to walking excavators (see 4.8.3). Compact excavators having an operating mass greater than 1 000 kg shall be fitted with a TOPS according to ISO 12117. For mandatory national and/or regional provisions, see ISO/TS 20474-14. 4.3.2.3 Protection for log application The excava
45、tor shall be equipped with a front protection and, if a relevant hazard exists, with a top protection, according to ISO 10262 and ISO 8084, as applicable. 4.3.3 Operators seat 4.3.3.1 Seat adjustment for compact excavators ISO 20474-1:2008, 4.4.1.3, shall apply only to excavators with an operating m
46、ass according to ISO 6016 of less than 3 000 kg. 4.3.3.2 Vibration For mandatory national and/or regional provisions, see ISO/TS 20474-14. 4.3.4 Rear window ISO 20474-1:2008, 4.3.2.9, shall apply except that the rear window of the excavator does not need to be equipped with window wipers, washers an
47、d defrosters. SANS 20474-5:2010This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 20474-5:2008(E) 4 ISO 2008 All rights reserved4.4 Controls for driving and steering ISO 20474-1:2008, 4.5.1 d) and 4.6.1, shall apply with the following additi
48、on: the movements of the controls for driving and steering do not need to correspond to the intended direction of movement if the upper structure is not in the normal driving direction. For mandatory national and/or regional provisions, see ISO/TS 20474-14. 4.5 Swing brakes For mandatory national an
49、d/or regional provisions, see ISO/TS 20474-14. 4.6 Stability and safety devices 4.6.1 General ISO 20474-1:2008, 4.11, shall apply with the additions given in 4.6.2 to 4.6.4. NOTE All rated capacities as defined hereafter are based on tests and/or calculations of machines on a level and firm supporting surface. The mass of the load, its density and the location of its centre of gravity, as well as the mass of the attachment and the attachment bracket,
