1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA
2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any
3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-23267-2 SANS 60745-2-1:2009Edition 2.1IEC 60745-2-1:2008Edition 2.1 SOUTH AFRICAN NATIONAL STANDARD Hand-held motor-operated electric tool
4、s Safety Part 2-1: Particular requirements for drills and impact drills This national standard is the identical implementation of IEC 60745-2-1:2008 and is adopted with the permission of the International Electrotechnical Commission. WARNING Can only be used in conjunction with SANS 60745-1. Publish
5、ed by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 60745-2-1:2009 Edition 2.1 IEC 60745-2-1:2008 Edition 2.1 Table of changes Change No. Date Scope IEC amdt 1 2008 Amended to change the scope, to
6、 make editorial changes to the copy, to add new drill safety warnings, to replace the existing text on the endurance requirements for impact drills, their components and construction, and to amend the text of annexes K and L. National foreword This South African standard was approved by National Com
7、mittee SABS TC 72, Safety of electrical appliances and electronic equipment, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This SANS document, by reference, forms part of the Compulsory specification for electrical and electronic a
8、pparatus, as published by Government Notice No. R. 89 (Government Gazette 31844) of 6 February 2009. This SANS document was published in October 2009. This SANS document supersedes SANS 60745-2-1:2004 (edition 2). IEC 60745-2-1Edition 2.1 2008-07INTERNATIONAL STANDARD NORME INTERNATIONALEHand-held m
9、otor-operated electric tools Safety Part 2-1: Particular requirements for drills and impact drills Outils lectroportatifs moteur Scurit Partie 2-1: Rgles particulires pour perceuses et perceuses percussion INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE CCICS 25.
10、140.20; 25.140.30 PRICE CODECODE PRIXISBN 2-8318-9865-X Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale SANS 60745-2-1:2009This s tandard may only be used and printed by approved subscription and freemailing clients
11、of the SABS . 2 60745-2-1 IEC:2003+A1:2008 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS SAFETY Part 2-1: Particular requirements for drills and impact drills FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standar
12、dization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes Inter
13、national Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate
14、 in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between t
15、he two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications ha
16、ve the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any mis
17、interpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding nati
18、onal or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition
19、 of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct
20、 or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensabl
21、e for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60745-2-1 has
22、 been prepared by subcommittee 61F: Safety of hand-held, motor-operated electric tools, of IEC technical committee 61: Safety of household and similar electrical appliances. This consolidated version of IEC 60745-2-1 consists of the second edition (2003) documents 61F/451/FDIS and 61F/471/RVD and it
23、s amendment 1 (2008) documents 61F/731/FDIS and 61F/751/RVD. The technical content is therefore identical to the base edition and its amendment and has been prepared for user convenience. It bears the edition number 2.1. A vertical line in the margin shows where the base publication has been modifie
24、d by amendment 1. The French version of this standard has not been voted upon. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. SANS 60745-2-1:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .60745-2-1 I
25、EC:2003+A1:2008 3 This part 2-1 is to be used in conjunction with the third edition of IEC 60745-1. When this standard states “addition”, “modification” or “replacement”, the relevant text in part 1 is to be adapted accordingly. With amendment 1, this Part 2 is established on the basis of the fourth
26、 edition (2006) of IEC 60745-1, Hand-held motor-operated electric tools Safety Part 1: General requirements. Main changes include editorial modifications to match with the fourth edition of IEC 60745-1 and the addition of a new safety warning to Clause 8: Marking and instructions. NOTE in this stand
27、ard, the following print types are used: requirements: in roman type; test specifications: in italic type; notes: in smaller roman type. IEC 60745 consists of the following parts, under the general title Hand-held motor-operated electric tools Safety: Part 1: General requirements Part 2-1: Particula
28、r requirements for drills and impact drills Part 2-2: Particular requirements for screwdrivers and impact wrenches Part 2-3: Particular requirements for grinders, polishers and disk-type sanders Part 2-4: Particular requirements for sanders and polishers other than disk type Part 2-5: Particular req
29、uirements for circular saws and circular knives Part 2-6: Particular requirements for hammers Part 2-7: Particular requirements for spray guns for non-flammable liquids Part 2-8: Particular requirements for shears and nibblers Part 2-9: Particular requirements for tappers Part 2-11: Particular requi
30、rements for reciprocating saws (jig and sabre saws) Part 2-12: Particular requirements for concrete vibrators Part 2-13: Particular requirements for chain saws Part 2-14: Particular requirements for planers Part 2-15: Particular requirements for hedge trimmers and grass shears Part 2-16: Particular
31、requirements for tackers Part 2-17: Particular requirements for routers and trimmers Part 2-18: Particular requirements for strapping tools Part 2-19: Particular requirements for jointers Part 2-20: Particular requirements for band saws Part 2-21: Particular requirements for drain cleaners The commi
32、ttee has decided that the contents of the base publication and its amendments will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdr
33、awn, replaced by a revised edition, or amended. SANS 60745-2-1:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS . 4 60745-2-1 IEC:2003+A1:2008 HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS SAFETY Part 2-1: Particular requirements for drills and i
34、mpact drills 1 Scope This clause of Part 1 is applicable, except as follows: Addition: This standard applies to drills and impact drills. 2 Normative references This clause of Part 1 is applicable. 3 Terms and definitions This clause of Part 1 is applicable, except as follows: Additional definitions
35、: 3.101 drill tool specifically designed to bore holes in various materials such as metal, plastics, wood, etc. 3.102 impact drill drill specifically designed to bore holes in concrete, stone and other materials. It is similar, in appearance and construction, to a drill, but has a built-in percussio
36、n system which gives an axial percussion movement to rotating output spindle It may have a device for rendering the percussion system inoperative, so that it may be used as a conventional drill. 4 General requirements This clause of Part 1 is applicable. 5 General conditions for the tests This claus
37、e of Part 1 is applicable, except as follows: 5.5 Addition: For drills which have both a mechanical means of setting different ranges of speed and an electronic means of setting the speed within a given range, the mechanical device is adjusted to the lowest range possible and the electronic device i
38、s adjusted to the highest setting within the given range. SANS 60745-2-1:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .60745-2-1 IEC:2003+A1:2008 5 6 Void 7 Classification This clause of Part 1 is applicable. 8 Marking and instructions
39、This clause of Part 1 is applicable, except as follows: 8.1 Addition: Drills and impact drills shall be marked with the following: rated no-load speed in revolutions per minute; maximum capacity, in millimetres, of the chuck. 8.12.1.1 Addition: Drill safety warnings Wear ear protectors when impact d
40、rilling. Exposure to noise can cause hearing loss. NOTE The above warning applies only to impact drills and may be omitted for drills other than impact drills. Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury. Hold power tool by insulated gripping surface
41、s, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a “live“ wire may make exposed metal parts of the power tool “live“ and could give the operator an electric shock. 9 Protection against access to live parts This clause
42、 of Part 1 is applicable. 10 Starting This clause of Part 1 is applicable. 11 Input and current This clause of Part 1 is applicable. 12 Heating This clause of Part 1 is applicable, except as follows: 12.2 Addition: Tools are operated continuously with the impact mechanism, if any, disengaged, while
43、the torque applied to the spindle is 80 % of the torque necessary to attain rated input or rated current. SANS 60745-2-1:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS . 6 60745-2-1 IEC:2003+A1:2008 12.3 Addition: The temperature-rise lim
44、it specified for the external enclosure does not apply to the enclosure of the impact mechanism. 13 Leakage current This clause of Part 1 is applicable. 14 Moisture resistance This clause of Part 1 is applicable. 15 Electric strength This clause of Part 1 is applicable. 16 Overload protection of tra
45、nsformers and associated circuits This clause of Part 1 is applicable. 17 Endurance This clause of Part 1 is applicable, except as follows: 17.2 Replacement for impact drills: Impact drills are operated with no load and, if the impact mechanism can be engaged and disengaged at will, the impact mecha
46、nism shall remain disengaged, for 12 h at supply voltage equal to 1,1 times rated voltage and then for 12 h at a supply voltage equal to 0,9 times rated voltage. The speed is adjusted to the highest value of the highest range. Each cycle of operation comprises an “on” period of 100 s and an “off” pe
47、riod of 20 s, the off periods being included in the specified operating time. During the test, the tool is placed in three different positions, the operating time, at each voltage, being approximately 4 h for each position. During this test, replacement of the carbon brushes is allowed, and the tool
48、 is oiled and greased as in normal use. The tool may be switched on and off by means of a switch other than that incorporated in the tool. The impact drills are then mounted vertically in a test apparatus as shown in Figure 101 and are operated at rated voltage or at the mean value of the rated volt
49、age range, for four periods of 6 h each, the interval between these periods being at least 30 min; if the impact mechanism can be engaged and disengaged at will, the impact mechanism shall remain engaged. During these tests, the impact drills are operated intermittently, each cycle comprising a period of operation of 30 s and a rest period of 90 s during which the tool remains switched off. During the tests, an axial force, just enough to ensure steady operation of the impact mechanism
