SIS 15 51 53-1974 Determination of dropping point of lubricating grease《润滑脂滴点的测定》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

SANS 1700-2-5-2003 Fasteners Part 2 Screw threads Section 5 ISO general purpose metric screw threads - Tolerances - Principles and basic data《紧固件 第2部分：螺纹 第5节：ISO一般用途米制螺纹 公差 原则和基本数据.pdf

SANS 1700-2-7-2003 Fasteners Part 2 Screw threads Section 7 ISO general purpose metric screw threads - Tolerances - Deviations for constructional screw threads《扣件 第2部分：螺纹 第7节：ISO普通.pdf

SANS 1700-2-9-1996 Fasteners Part 2 Screw threads Section 9 ISO general-purpose metric screw threads - Gauges and gauging《紧固件 第2部分 螺纹 第9子部分 ISO普通公制螺纹 量规和测量》.pdf

SANS 1700-3-1-1996 Fasteners Part 3 Forms dimensions and designations Section 1 Bolts screws studs and nuts - Symbols and designations of dimensions《紧固件 第3部分：形式，尺寸和名称 第1部分：螺栓，螺柱和螺母.pdf

SANS 1700-3-10-1996 Fasteners Part 3 Forms dimensions and designations Section 10 Bolts screws and studs - Split pin holes and wire holes《紧固件 第3部分：形式，尺寸和名称 第10部分：螺栓，螺钉和双头螺柱 开口销孔和穿丝.pdf

SANS 1700-3-11-1996 Fasteners Part 3 Forms dimensions and designations Section 11 Countersunk head screws - Head configuration and gauging《紧固件 第3部分：形式，尺寸和名称 第11部分：沉头螺钉的头形和测量》.pdf

SANS 1700-3-12-1996 Fasteners Part 3 Forms dimensions and designations Section 12 Countersunk flat head screws - Penetration depth of cross recesses《紧固件 第3部分 形状、尺寸和命名 第12子部分 埋头螺钉 十.pdf

SANS 1700-3-13-1996 Fasteners Part 3 Forms dimensions and designations Section 13 Designation system for fasteners《紧固件 第3部分：形式，尺寸和名称 第13部分：紧固件的名称与符号体系》.pdf

SANS 1700-3-2-1996 Fasteners Part 3 Forms dimensions and designations Section 2 Hexagon products - Widths across flats《紧固件 第3部分：形式，尺寸和名称 第2部分：六角产品 对边宽度》.pdf