SIS 16 06 04-1959 Ethylene glycol《乙二醇》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

NF J65-150-1958 SHIPBUILDING SHAFT LINES COUPLINGS FORGED FLANGES FOR ASSEMBLY TO FORGED FLANGES 《造船工业 轴线 联轴节 装配锻接凸缘机的锻接法兰》.pdf

NF J65-155-1958 Shipbuilding Shaft lines Couplings Forged flanges for assembly to taper-bore flanges 《造船工业 轴线 联轴节 装配镗圆锥孔凸缘的锻接法兰》.pdf

NF J65-160-1958 Shipbuilding Shaft lines Couplings Taper bore flanges 《造船工业 轴线 联轴节 镗圆锥孔凸缘》.pdf

NF J65-165-1958 Shipbuilding Shaft lines Couplings Shaft ends keys nuts 《造船工业 轴衬线 联轴器 轴端、键和螺母》.pdf

NF J65-170-1958 SHIPBUILDING SHAFT LINES COUPLINGS MUFF COUPLINGS 《造船工业 轴线 联轴节 套筒联轴节》.pdf

NF J65-175-1958 Shipbuilding Shaft lines Couplings Details of shaft ends keys and assembly bolts for muff couplings 《造船工业 轴线 联轴器 轴端零件、键和MUFF联轴器装配螺栓》.pdf

NF J65-180-1958 Shipbuilding Shaft lines Couplings Taper bore flanges General arrangement Nut locking plates 《造船工业 轴线 联轴节 镗圆锥孔凸缘机 总布局 螺母锁紧板》.pdf

NF J65-199-1995 Small craft with inboard engine Propeller shaft ends and bosses with 1 10 taper 《舱内安装发动机的小艇 锥度为1 10螺旋浆轴端和轴套》.pdf

NF J65-510-1985 Shipbuilding Ship screw propellers Manufacturing tolerances Part 1 propellers of diameter greater than 2 50 M 《造船工业 船用螺旋桨 制造公差 第一部分：直径大于2 5m的螺旋桨》.pdf