搜索
麦多课文库
收藏
下载资源
加入VIP,免费下载
SIS SMS 1361-1950 《仪器,螺纹,螺纹公差最小和最大,参考螺纹,磨损最大,标准内直径超过18至180》.pdf
上传人:
explodesoak291
文档编号:1037948
上传时间:2019-03-24
格式:PDF
页数:1
大小:36.45KB
下载
相关
举报
第1页 / 共1页
亲,该文档总共1页,全部预览完了,如果喜欢就下载吧!
资源描述
展开
阅读全文
相关资源
IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf
IRS 70712-2018 Rail defects.pdf
IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf
IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf
IESNA TM-23-2017 Lighting Control Protocols.pdf
IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf
ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf
ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf
ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf
ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf
猜你喜欢
GOST 20692-2003 Roller bits Specifications《牙轮钻头 型式及基本尺寸》.pdf
GOST 20693-1975 Hign-voltage kenotrons Terms and definitions《高压整流二极管 术语和定义》.pdf
GOST 20694-1975 Twist drills with straight shanks for hard to machine materials Short series Construction and dimensions《难加工材料加工用圆柱柄麻花钻 短型 结构及尺寸》.pdf
GOST 20695-1975 Twist drills with straight shanks for hard to machine materials Middle series Construction and dimensions《难加工材料加工用圆柱柄麻花钻 中型 结构及尺寸》.pdf
GOST 20696-1975 Twist drills with taper shanks for hard to machine materials Short series Construction and dimensions《难加工材料加工用锥柄麻花钻 短型 结构及尺寸》.pdf
GOST 20697-1975 Twist drills with taper shanks for hard to machine materials Middle series Construction and dimensions《难加工材料加工用锥柄麻花钻 中型 结构及尺寸》.pdf
GOST 20698-1975 Twist drills for hard to machine materials Specifications《难加工材料加工用麻花钻 技术要求》.pdf
GOST 20706-1975 Microtalc for cable industry Specifications《电缆工业用细滑石粉 技术条件》.pdf
GOST 20715-1975 Polyamid industrial fabrics for wedge belts Specifications《三角皮带用的聚酰胺织物 技术条件》.pdf
相关搜索
SISSMS13611950
仪器
螺纹
公差
最小
最大
参考
磨损
标准
直径
超过
18
180
PDF
当前位置:
首页
>
标准规范
>
国际标准
>
其他
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:
苏ICP备17064731号-1
登录
首页
资源分类
专题
通知公告