SIS SMS-GUIDE 14-1991 《一般公差》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD WSK-M4D800-A-2010 POLYETHYLENE (PE) HIGH DENSITY HIGH MELT FLOW RATE LOW IMPACT MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《高密度高熔体流速低抗冲聚乙烯（PE）成型料 与标准FORD WSS-M99P.pdf

FORD WSK-M4D801-A-2010 POLYAMIDE (PA) 12 RIGID HEAT STABILIZED 12% GRAPHITE FILLED MOLDING AND EXTRUSION COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《12%石墨填充的受热稳定的刚性聚酰胺12模塑和挤塑成型.pdf

FORD WSK-M4D802-A-2010 POLYAMIDE (PA) 12 SEMI-FLEXIBLE HEAT STABILIZED MOLDING AND EXTRUSION COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《半柔性、受热稳定的聚酰胺12模塑和挤塑成型料 与标准FORD WSS-M99.pdf

FORD WSK-M4D804-A-2006 POLYAMIDE (PA) 6 HEAT STABILIZED IMPACT MODIFIED BLOW MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《受热稳定的聚酰胺6冲击改性吹塑成型料 与标准FORD WSS-M99P1111-A一起使用 .pdf

FORD WSK-M4D805-A-2013 POLYVINYL CHLORIDE (PVC) FOAM CLOSED CELL TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSK-M4D806-A-2008 ABS MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《丙烯腈-丁二烯-苯乙烯共聚物(ABS)成型料 与标准FORD WSS-M99P1111-A一起使用 [使用 FORD ESB-M4D483-A1 FORD ESB-M4D483-A1 FOR.pdf

FORD WSK-M4D807-A2-2006 POLYPHENYLENE SULFIDE (PPS) 40 % GLASS FIBER REINFORCED SELF-EXTINGUISHING MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《40%玻璃纤维增强的聚苯硫醚(PPS)自熄灭型成型.pdf

FORD WSK-M4D808-A-2006 POLYPHENYLENE SULFIDE (PPS) 45% GLASS FIBER REINFORCED SELF EXTINGUISHING MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《45%玻璃纤维增强的聚苯硫醚(PPS)自熄型成型料 .pdf

FORD WSK-M4D811-A-2010 POLYAMIDE (PA) 46 HEAT STABILIZED OIL IMPREGNATED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《油浸渍、受热稳定的聚酰胺46成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf