SIS SS-EN 10 163-1-1992 Delivery requirements for surface condition of hot rolled steel plates wide flats and sections Part 1 General requirements《热轧钢板表面状况的交货要求，宽带钢和部分 第1部分：一般要求》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD WSB-M4D831-A-2009 THERMOPLASTIC POLYURETHANE ELASTOMER (TPUR) 65 DUROMETER D HARDNESS MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《硬度65 D的热塑性聚氨酯弹性体(TPUR)成型料 与标准FOR.pdf

FORD WSB-M4D833-A-2013 ACRYLONITRILE STYRENE ACRYLATE (ASA) MEDIUM HEAT RESISTANT MOLDING COMPOUND EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSB-M4D834-A-2010 POLYPROPYLENE (PP) 15% GLASS SPHERE REINFORCED HEAT STABILIZED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《15%玻璃珠增强的受热稳定的聚丙烯（PP）成型料 与标准FORD WSS-.pdf

FORD WSB-M4D835-A-2010 POLYARYLSULFONE (PAS) MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《聚芳砜（PAS）成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD WSB-M4D840-A4-2006 ACETAL (POM) COPOLYMER COLOR PIGMENTED MOLDING COMPOUND MELT FLOW RATE 1 8 - 4 0 INTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车内部用熔体流动速率为1 8-4 0的乙缩醛共聚物(.pdf

FORD WSB-M4D841-A-2013 POLYPROPYLENE (PP) COPOLYMER 15% MINERAL FILLED COLOR PIGMENTED INTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSB-M4D841-A2-2011 POLYPROPYLENE (PP) COPOLYMER 16% MINERAL FILLED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《16%矿物填充模塑材料聚丙烯(PP)共聚物 与福特WSS-M99P1111-A 一起使用》.pdf

FORD WSB-M4D841-A3-2005 POLYPROPYLENE (PP) COPOLYMER 13% TALC FILLED COLOR PIGMENTED MOLDING COMPOUND INTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车内部用13%滑石粉填充的着色型聚丙烯(PP)共聚物成型料.pdf

FORD WSB-M4D842-A-2010 POLYPROPYLENE (PP) COPOLYMER 26% MINERAL FILLED COLOR PIGMENTED INTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车内部用26%矿物填充的着色型聚丙烯(PP)共聚物成型料 与标准FORD WSS-M9.pdf